Model: alderlea t4, t4 classic series - c alderlea t4 important: keep these instructions for future reference. Installation and operating instructions - australia safety notice if this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Co...
?pacific energy fireplace products ltd. Note: we strongly r e c o m m e n d t h at smoke detectors be installed. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to curing of stove paint or fumes caused by accidentally leaving...
?pacific energy fireplace products ltd. 3 010515-20 alt4 safety and maintenance 1. Burn only dry, well seasoned wood. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you f...
?pacific energy fireplace products ltd. 4 010515-20 alt4 check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (see website for descriptions and more detail) weekly: - firebrick - visual, for cracking. - door gasket - sagging, placement,...
?pacific energy fireplace products ltd. 5 010515-20 alt4 creosote formation and need for removal when wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow b...
Fig #1 appliance dimensions outside air opening dimensions 660mm 527mm 146mm 714mm ©pacific energy fireplace products ltd. 105mm outside air inlet 9.5mm 59mm 105mm outside air inlet 32mm 105mm outside air inlet 79mm cl cl cl cl cl cl we recommend that our woodburning hearth products be installed and...
?pacific energy fireplace products ltd. Do not connect this unit to a chimney flue serving another appliance. 7 010515-20 alt4 installation warning: under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It may be fired only after the stove is installed properly....
Fig #2 single wall connector 375mm 350mm 527mm 660mm 250mm 250mm 570mm minimum clearances to combustibles fig #2a single wall connector with shield 250mm 350mm 400mm 660mm 200mm 200mm 520mm minimum clearances to combustibles ©pacific energy fireplace products ltd. Fig #3 non-combustible floor protec...
?pacific energy fireplace products ltd. Chimney and connector warning: install chimney and all components of chimney system according to chimney manufacturer’s instructions. Connect to a listed chimney complying with the requirements of as/nzs2918/2001 and a chimney suitable for use with solid fuel ...
?pacific energy fireplace products ltd. 10 010515-20 alt4 this package contains 12 full-size firebricks, as well as 2 various cut bricks. With the heater in the upright position, install firebricks as follows: 1. Install 4 full-size firebricks against the rear wall. 2. Install the side firebricks, 2...
?pacific energy fireplace products ltd. Intake or combustion air can be supplied to the stove in one of two ways. Consult your local build- ing codes before proceeding. 1. Outside air supply - (necessary for mobile home installation, optional for residential installa- tion.) to draw outside air thro...
?pacific energy fireplace products ltd. 12 010515-20 alt4 operation caution: never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or "freshen up" a fire in this heater. Keep all such liquids well away from the heater while it is in use. Caution...
?pacific energy fireplace products ltd. 13 010515-20 alt4 how to test your wood add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more than one side within one minute. It is damp if it turns black and lights within three minutes. If it sizzle...
?pacific energy fireplace products ltd. 14 010515-20 alt4 restarting after extended or overnight burns 1. Open door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of embers, close door. 2. Adjust air control to high (left position) and in just a few minut...
?pacific energy fireplace products ltd. 15 010515-20 alt4 chimney connector pipe should be disconnected from stove to clean and inspect. Only if this is not possible should you remove baffle assembly. Do not operate with baffle assembly or insulation removed. Removal remove retaining pin located at ...
?pacific energy fireplace products ltd. 16 010515-20 alt4 problem cause cure glass is dirty 1. Wood is wet • use dry wood 2. Turning down air control • do not turn down until or damper too soon a) there is a good bed of coals b) the wood is charred 3. Draft too low • improper chimney height and / or...
?pacific energy fireplace products ltd. All other parts not included in above kits are not sold separately right and left are determined when facing the front of the stove #1 baffle kit ................................................... Vist.Bafkit #2 brick rails set ..................................
?pacific energy fireplace products ltd. 18 010515-20 alt4.
?pacific energy fireplace products ltd. Compliance plate location rear view 19 010515-20 alt4 compliance plate alderea t4 c when tested in accordance with: as/nzs 4012:1999 & as/nzs4013:1999 hcmg/13/047a 30/sept/2013 freeestanding tested by: hrl technology pty ltd tramway road, morwell, victoria max...
?pacific energy fireplace products ltd. Pacific energy fireplace products ltd. Web site: www.Pacificenergy.Net 2975 allenby rd., duncan, bc v9l 6v8 printed in canada.
