1. DL manuals
  2. Packard Bell
  3. Laptop
  4. EasyNote DT85
  5. Service Manual

Packard Bell EasyNote DT85 Service Manual

Summary of EasyNote DT85

  • Page 1

    Easynote dt85 service guide.

  • Page 2

    Revision history please refer to the table below for the updates made on the easynote dt85 service guide. Service guide files and updates are available on the acer/csd web. For more information, refer to http://csd.Acer.Com.Tw copyright © 2009 packard bell is a registered trademark of packard bell b...

  • Page 3

    Contents i chapter 1: system specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Contents ii creating the crisis recovery disk . . . . . . . . . . . . . . . . . . . . 41 performing a bios recovery . . . . . . . . . . . . . . . . . . . . . . . . 41 running the flash utility: . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 clearing a bios password . . . . . . . . . . . . ...

  • Page 5

    Iii www.Packardbell.Com replacing the lcd assembly lid . . . . . . . . . . . . . . . . . . . . . . . . 134 chapter 4: troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 diagnosing problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 s...

  • Page 6

    Contents iv appendix c: online support information . . . . . . . . . . . . . . . . . . . . . . . . 195 online support information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196.

  • Page 7: •

    Chapter1 1 system specifications • preface • features • system block diagram • hardware specifications • notebook product tour • keyboard • touchpad • webcam.

  • Page 8

    Chapter 1: system specifications 2 preface conventions the following conventions are used in this manual: general information before using this information and the product it supports, read the following general information. • this service guide provides you with all technical information relating t...

  • Page 9

    Www.Packardbell.Com 3 features platform • intel ® – processor: intel core™2 duo processor (2.0–2.4 ghz or above) with 1066/800 mhz fsb – core logic: intel gm45 (north bridge) + intel ich9m (south bridge) • wireless: intel wifi link 5100 a/b/g/n, lite-on atheris b/g/n system memory • two dimm slots s...

  • Page 10

    Chapter 1: system specifications 4 input devices • 99-,100-, or 103-key keyboard, 2.5 mm (minimum) key travel • function keys, system keys, navigation keys, fn key, windows key, application key, arrow keys, and a separate numeric keypad • touchpad pointing device • capacitive hotkeys audio • 2.1 ste...

  • Page 11

    Www.Packardbell.Com 5 security • kensington lock • bios-based user, supervisor, and hdd passwords physical specifications • dimensions: 441.1 × 300 × 40.2/44.2 mm (17.37 × 11.81 × 1.58/1.74 in) • weight: 4.1 kg. (9.04 lbs.) environment • temperature – operating: 32 to 90 °f (0 to 35 °c) – non-operat...

  • Page 12

    Chapter 1: system specifications 6 system block diagram.

  • Page 13

    Www.Packardbell.Com 7 hardware specifications processor controllers item specification type intel core 2 duo, pentium dual-core, celeron mobile processor processor package socket-p, µfcpga processor core voltage 1.0375v to 1.3v core logic intel gm45 + ich9m item intel platform core logic intel gm45 ...

  • Page 14

    Chapter 1: system specifications 8 bios memory item specification bios vendor phoenix bios version v1.01 bios rom type 3v bios rom size 16 mb bios package 8-sop supported protocols acpi 1.0b/2.0/3.0 compliance, pci 2.2, system/hdd password security control, int 13h extenstions, pnp bios 1.0a smbios ...

  • Page 15

    Www.Packardbell.Com 9 hard drive optical drive item specification model seagate st9160310as toshiba mk1655gsx hitachi hts543216l9a30 0 western digital wd1600bevt-22z ct0 seagate st9250315as and st9250320as toshiba mk2555gsx hitachi hts545025b9a300 western digital wd2500bevt-22zct 0 seagate st9320320...

  • Page 16

    Chapter 1: system specifications 10 lcd transfer rate sustained: • with cd: max 3.6 mbytes/sec • with dvd: max 10.08 mbytes/sec sustained: • with cd: max 3.6 mbytes/sec • with dvd: max 10.8 mbytes/sec • with bd: max 11 mbytes/sec buffer memory 2 mb • for cd/dvd: 2 mb • for bd: 4.5 mb interface sata ...

  • Page 17

    Www.Packardbell.Com 11 audio video display mode normally white brightness (nits) 250 / 220 luminance uniformity 1.25 max. Contrast ratio 400–500 typical response time (ms) 8 nominal input voltage +3.3 v viewing angle horizontal: right/left vertical: upper/lower 45/45 15/35 temperature (°c) operating...

  • Page 18

    Chapter 1: system specifications 12 features • intel gen 5.0 integrated graphics engine with ten, fully-programmable cores • supports hdmi/dvi, dp, tv-out, lvds, crt and sdvo • intel ® dynamic video memory technology (intel® dvmt 5.0) • video capture via x1 concurrent pci express port • pavp (protec...

  • Page 19

    Www.Packardbell.Com 13 keyboard pointing device memory card reader item specification controller winbond wpc773 type 99- ,100 or 103-key, 2.5 mm (minimum) key travel key types function keys, system keys, navigation keys, fn key, windows key, application key, arrow keys, and separate numeric keypad c...

  • Page 20

    Chapter 1: system specifications 14 wired lan wireless lan bluetooth item specification chipset broadcom bcm5784 data throughput 10/100/1000 mbps lan connector type rj45 lan connector location left side features • integrated 10/10/1000 base-t transceiver • pci v2.2 compliant • wake on lan support me...

  • Page 21

    Www.Packardbell.Com 15 usb buttons/indicators/ports webcam item specification chipset • intel ich9m usb compliancy level 2.0 ohci usb 1.1 and usb 2.0 host controller number of usb ports 4 location • two on the left side • two on the right side item specification buttons • power button • capacitive h...

  • Page 22

    Chapter 1: system specifications 16 cooling fan battery ac adapter processor temperature (°c) fan speed (rpm) acoustic level (dba) 45-50 0-3000 29 55-66 0-3300 33 68-74 3300-3800 38 78-83 3800-4100 40 86-91 4100-4800 40 note: throttling 50%: % is controlled by operating system. Temperature point is ...

  • Page 23

    Www.Packardbell.Com 17 power management acpi mode description g3 mechanical off - all devices in the system are turned off completely. No electrical current is running through the system. Except for the real-time clock, power consumption is zero. The machine can be worked on without damaging the har...

  • Page 24

    Chapter 1: system specifications 18 notebook product tour front view note: 1. Charging: the light shows amber when the battery is charging. 2. Fully charged: the light shows green when in ac mode. Important case color may vary from that shown in the pictures. # icon item description 1 5-in-1 card re...

  • Page 25

    Www.Packardbell.Com 19 left view # icon item description 1 dc-in jack connects to an ac adapter. 2 hdmi out jack (optional) hdmi plug an hdmi device, such as a high definition television, into this optional jack. 3 external display (vga) port connects to a display device (e.G., external monitor, lcd...

  • Page 26

    Chapter 1: system specifications 20 right view rear view # icon item description 1 usb 2.0 ports connects to usb 2.0 devices (e.G., usb mouse, usb camera). 2 optical drive internal optical drive; accepts cds or dvds. 3 optical disk access indicator lights up when the optical drive is active. 4 optic...

  • Page 27

    Www.Packardbell.Com 21 top view note: the lcd and the keyboard are separate pictures and were joined together for better clarification. 11.

  • Page 28

    Chapter 1: system specifications 22 # icon item description 1 power button / indicator turns the computer on and off. / indicates the computer's power status. 2 touchpad toggle turns the internal touchpad on and off. Backup key launches acer backup management for three-step data backup. Acer powersm...

  • Page 29

    Www.Packardbell.Com 23 bottom view # icon item description 1 subwoofer emits low frequency sound output. 2 bottom cover houses the memory, hard drive, cpu, and wlan card. 3 battery release latch releases the batter for removal. 4 battery bay houses the computer’s battery pack. 5 battery lock locks t...

  • Page 30

    Chapter 1: system specifications 24 keyboard your notebook features a full-size keyboard that functions the same as a desktop computer keyboard. Many of the keys have been assigned alternate functions, including shortcut keys for windows and function keys for specific system operations. Key types th...

  • Page 31

    Www.Packardbell.Com 25 system key combinations when you press the f n key and a system key at the same time, your notebook performs the action identified by the text or icon on the key. Press and hold f n , then press this system key... To... Turn the capacitive touch key leds on or off. Enter sleep...

  • Page 32

    Chapter 1: system specifications 26 touchpad when you move your finger on the touchpad, the pointer (arrow) on the screen moves in the same direction. You can use the scroll zone to scroll through documents. Use of the scroll zone may vary from program to program. You can use the left and right butt...

  • Page 33

    Www.Packardbell.Com 27 webcam you can use the optional webcam with many of the available internet chat programs to add video and audio to your chat session. In addition, by using the software included with the webcam, you can take pictures or create video clips. Start a program or open a file or fol...

  • Page 34

    Chapter 1: system specifications 28.

  • Page 35: •

    Chapter2 29 system utilities • bios setup utility • bios recovery • clearing a bios password • unlocking the hard drive.

  • Page 36

    Chapter 2: system utilities 30 bios setup utility the bios setup utility is a hardware configuration program built into the notebook’s bios (basic input/output system). The notebook was shipped already properly configured and optimized. However, if the user encounters configuration problems, you may...

  • Page 37

    Www.Packardbell.Com 31 navigating the bios setup utility use the keys listed in the legend bar on the bottom of the setup screen to work your way through the various menu and submenu screens. To use the bios setup utility: • to choose a menu, use the left ← and right → arrow keys. • to choose an ite...

  • Page 38

    Chapter 2: system utilities 32 information the information menu displays a summary of your computer hardware information. These information are necessary for troubleshooting and may be required when asking for technical support. Parameter description cpu type displays the processor model and speed. ...

  • Page 39

    Www.Packardbell.Com 33 main use the main menu to set the system time and date, and other basic options. Manufacturer name displays the name of the computer manufacturer. Uuid number displays the computer’s uuid (universally unique identifier). Uuid is an identifier standard used in software construc...

  • Page 40

    Chapter 2: system utilities 34 quiet boot enables or disables the quiet boot function. When enabled, bios setup is in graphical mode and displays only the computer brand logo during post and while booting. When disabled, bios setup is in conventional text mode and displays the system summary screen....

  • Page 41

    Www.Packardbell.Com 35 security use the security menu option to set system passwords to protect your computer from unauthorized use. . Parameter description option supervisor password is displays the supervisor password status. Clear set user password is displays the user password status. Clear set ...

  • Page 42

    Chapter 2: system utilities 36 setting a password note the following reminders before you define a system password: • the maximum length of password contains 8 alphanumeric characters. • system passwords are case-insensitive. • when typing the password, only shaded blocks representing each typed cha...

  • Page 43

    Www.Packardbell.Com 37 to set a supervisor password: 1 press ↑ or ↓ to highlight set supervisor password , then press enter . The set supervisor password box opens. 2 type a password, then press enter . 3 retype the password to verify the first entry, then press enter . You will be prompted to save ...

  • Page 44

    Chapter 2: system utilities 38 5 press enter . A dialog box will appear confirming that changes have been made. 6 press f10 to save the password and close the setup utility or you can proceed to setting a user password. Removing a password to remove a password: 1 press ↑ or ↓ to highlight the set su...

  • Page 45

    Www.Packardbell.Com 39 boot use the boot menu to set the preferred drive sequence in which the setup utility attempts to boot the operating system. To set boot drive sequence: 1 press ↑ or ↓ to highlight a bootable device. 2 press f5 or f6 to move the selected device up or down the boot sequence. 3 ...

  • Page 46

    Chapter 2: system utilities 40 exit the exit menu screen lists options for quitting from the setup utility. Option description exit saving changes saves changes made and closes the setup utility. Keyboard shortcut: f10 exit discarding changes discards changes made and closes the setup utility. Load ...

  • Page 47

    Www.Packardbell.Com 41 bios recovery an interruption during a bios flash procedure (e.G. A power outage) can corrupt the bios code, which will cause the system to go into an unbootable state. You need to access and execute the boot block program to reboot the computer and recover the regular bios co...

  • Page 48

    Chapter 2: system utilities 42 running the flash utility: to run the flash utility: 1 rename the bios file as “xxxxxxx.Fd”. 2 copy the “xxxxxxx.Fd” file to a bootable usb device containing the crisis recovery disk files. 3 turn off the computer. 4 insert the usb device containing the renamed bios fi...

  • Page 49

    Www.Packardbell.Com 43 clearing a bios password to clear a lost bios password (user or supervisor password) you need to short the clear password hardware gap g35 located near the lcd connector on the system board. Hw default setting function gap open (normal) short to clear the user and supervisor p...

  • Page 50

    Chapter 2: system utilities 44 to clear a bios password: 1 turn off the notebook and unplug all the peripherals connected to it. 2 complete the steps in “removing the battery” on page 54 . 3 complete the steps in “removing the bay cover” on page 55 . 4 5 use an electrical conductivity tool to short ...

  • Page 51

    Www.Packardbell.Com 45 unlocking the hard drive to regain access to your computer if you lose the hdd password, you need to generate a master password and unlock the hard drive. To unlock a hard drive: 1 open the computer in a dos environment. 2 type the following command: a\> unlock6 xxxxx 00 3 pre...

  • Page 52

    Chapter 2: system utilities 46.

  • Page 53: •

    Chapter3 47 replacing notebook components • preventing static electricity discharge • preparing the work space • required tools • preparing the notebook • removing the battery • removing the bay cover • adding or replacing memory modules • replacing the wireless card • replacing the hard drive 1 • r...

  • Page 54

    Chapter 3: replacing notebook components 48 preventing static electricity discharge the components inside your notebook are extremely sensitive to static electricity, also known as electrostatic discharge (esd). Before performing maintenance on the notebook, follow these guidelines: • avoid static-c...

  • Page 55

    Www.Packardbell.Com 49 preparing the work space before performing maintenance on the notebook, make sure that your work space and the notebook are correctly prepared. • wear a grounding (esd) wrist strap, and use a grounded or dissipative work mat. • use a sturdy table. Make sure that the table top ...

  • Page 56

    Chapter 3: replacing notebook components 50 required tools to disassemble the notebook, you need the following tools: • wrist grounding strap (for esd prevention) • conductive mat (for esd prevention) v • flat screwdriver v • phillips screwdriver v • non-marring plastic scribe v.

  • Page 57

    Www.Packardbell.Com 51 preparing the notebook to prepare the notebook for maintenance: 1 make sure that the optical disc drive is empty. 2 turn off the notebook. 3 c lose the lcd panel. 4 disconnect the ac adapter. 5 disconnect the network cable and all peripheral devices connected to the notebook. ...

  • Page 58

    Chapter 3: replacing notebook components 52 b pull the express card out of its slot. 7 make sure there is no memory card on the card reader slot. To remove a memory card: a push against the card, as if you were pushing it further into the slot, letting the card spring out.

  • Page 59

    Www.Packardbell.Com 53 b pull the memory card out of its slot..

  • Page 60

    Chapter 3: replacing notebook components 54 removing the battery to remove the battery: 1 turn the notebook over so the base is facing up. 2 slide the battery lock to the unlocked position (1); slide the battery latch (2), then remove the battery out of the notebook (3). Note the battery has been hi...

  • Page 61

    Www.Packardbell.Com 55 removing the bay cover to remove or replace components located on the lower bay, you need to remove the bay cover first. Tools you need to complete this task: to remove the bay cover: 1 complete the steps in “preparing the notebook” on page 51 . 2 turn the notebook over so the...

  • Page 62

    Chapter 3: replacing notebook components 56 4 insert a non-marring plastic scribe on the cover’s notch to release the cover from the computer, and then remove the cover..

  • Page 63

    Www.Packardbell.Com 57 adding or replacing memory modules tools you need to complete this task: to add or replace memory modules: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing the bay cover” on page 55 . 3 if you are replacing a memory module, go to ...

  • Page 64

    Chapter 3: replacing notebook components 58 replacing the wireless card tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (wireless card) to replace the wireless card: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing...

  • Page 65

    Www.Packardbell.Com 59 4 unplug the antenna cables. Note which color cable corresponds to each of the connectors. 5 move the antenna cables away from the wireless card screw. 6 remove the screw securing the wireless card. Important the number of antenna cables varies depending on the type of wireles...

  • Page 66

    Chapter 3: replacing notebook components 60 7 pull the card out of the slot. 8 insert the new wireless card at a 30° angle into the empty mini card slot. The card is keyed so it can only be inserted in one direction. If the card does not fit, make sure that the notch in the card lines up with the ta...

  • Page 67

    Www.Packardbell.Com 61 replacing the hard drive 1 tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (hard drive 1) • 4 chrome m3×3 (hard drive bracket) to replace the hard drive: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps i...

  • Page 68

    Chapter 3: replacing notebook components 62 4 grasp the black mylar tab and use it to disengage the hard drive from its connector, and then remove the drive from its bay. 5 if your new hard drive already includes the hard drive bracket, go to step 9 . If you need to use the bracket from the old hard...

  • Page 69

    Www.Packardbell.Com 63 7 remove the hard drive from the bracket. 8 place the bracket on the new drive and secure it with the screws removed in step 6 . 9 slide the new hard drive into the hard drive bay and make sure it’s properly engaged to the connector. 10 secure the new drive to the system board...

  • Page 70

    Chapter 3: replacing notebook components 64 replacing the hard drive 2 tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (hard drive 2) • 4 chrome m3×3 (hard drive bracket) to replace the hard drive 2: 1 complete the steps in “preparing the notebook” on page 51 ....

  • Page 71

    Www.Packardbell.Com 65 3 remove the hard drive screw. 4 grasp the black mylar tab and use it to disengage the hard drive from its connector, and then remove the drive from its bay. 5 if your new hard drive already includes the hard drive bracket, go to step 9 . If you need to use the bracket from th...

  • Page 72

    Chapter 3: replacing notebook components 66 6 remove the screws that secure the hard drive bracket. 7 remove the hard drive from the bracket. 8 place the bracket on the new drive and secure it with the screws removed in step 6 . 9 slide the new hard drive into the hard drive bay and make sure it’s p...

  • Page 73

    Www.Packardbell.Com 67 replacing the optical drive tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (optical drive) • 1 chrome m2×4 (optical drive bracket) to replace the optical drive: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the...

  • Page 74

    Chapter 3: replacing notebook components 68 4 use the non-marring plastic scribe to carefully push the optical drive out of the drive bay, and then slide the drive out. 5 if your new optical drive already has it’s own bracket and bezel, go to step 10 . If you need to use the bracket and bezel from t...

  • Page 75

    Www.Packardbell.Com 69 7 detach the bracket from the drive. 8 attach the bezel to the new optical drive. 9 attach the bracket to the new optical drive and secure it with the screw removed in step 6 . 10 slide the new optical drive into the drive bay and make sure it’s properly engaged to the odd1 co...

  • Page 76

    Chapter 3: replacing notebook components 70 replacing the thermal module note: the thermal module in this sample is for the discrete model. For the uma model, the thermal module have four captive screws. Tools you need to complete this task: to replace the thermal module: 1 complete the steps in “pr...

  • Page 77

    Www.Packardbell.Com 71 4 loosen the spring-loaded captive screws securing thermal module. Follow the screw sequence indicated on the below images. 5 remove the thermal module from the system board. 1 2 3 4 5 6 7 8.

  • Page 78

    Chapter 3: replacing notebook components 72 6 lay the thermal module down in an upright position to avoid tainting your work space with thermal grease. 7 remove the barcode sticker on top of the processor. 8 moisten a soft cloth with isopropyl alcohol and clean the processor die to remove any therma...

  • Page 79

    Www.Packardbell.Com 73 replacing the cpu tools you need to complete this task: to replace the cpu: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing the bay cover” on page 55 . 3 remove the thermal module by following the instructions in “replacing the t...

  • Page 80

    Chapter 3: replacing notebook components 74 6 remove the old processor from the system board. 7 install the new processor onto the system board making sure that pin 1 on the processor (indicated by the silk-screened arrow on the corner of the processor) aligns with pin 1 on the processor socket (ind...

  • Page 81

    Www.Packardbell.Com 75 replacing the vga board (for discrete models) tools you need to complete this task: screws removed during this task: • 2 black m2×4 (vga board) to replace the vga board (for discrete models): 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in...

  • Page 82

    Chapter 3: replacing notebook components 76 5 remove the vga board. 6 install the vga board, then replace the screws removed in step 4 . 7 remove any thermal grease residue from the cooling assembly using a soft cloth and isopropyl alcohol. 8 place new thermal grease on the vga chip on the vga board...

  • Page 83

    Www.Packardbell.Com 77 replacing the keyboard tools you need to complete this task: to replace the keyboard: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing the battery” on page 54 . 3 turn the notebook over and open the lcd panel to its fully extended...

  • Page 84

    Chapter 3: replacing notebook components 78 6 disconnect the keyboard cable and remove the old keyboard. 7 connect the cable from the new keyboard into the connector. 8 insert the tabs on the front edge of the keyboard into the slots under the palm rest. You may need to press down on the keyboard ke...

  • Page 85

    Www.Packardbell.Com 79 replacing the keyboard cover tools you need to complete this task: to replace the keyboard cover: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing the battery” on page 54 . 3 remove the keyboard by following the steps in “replacin...

  • Page 86

    Chapter 3: replacing notebook components 80 the left and right media boards are glued to the keyboard cover. 6 use the plastic scribe to carefully pry loose the middle cover from the latches securing it. Then remove it from the system. 7 replace the new keyboard cover and carefully push down on all ...

  • Page 87

    Www.Packardbell.Com 81 replacing the power button board tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (power button board) to replace the power button board: 1 complete the steps in “preparing the notebook” on page 51 . 2 complete the steps in “removing the b...

  • Page 88

    Chapter 3: replacing notebook components 82 6 carefully remove the power button board and turn in over to access the cable. 7 disconnect the cable from the power button board and remove it from the system. 8 reconnect the cable to the new power button board and replace it back to the system. 9 repla...

  • Page 89

    Www.Packardbell.Com 83 replacing the lcd panel assembly tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) to replace the lcd panel assembly: 1 complete the steps in “preparing the notebook” on...

  • Page 90

    Chapter 3: replacing notebook components 84 8 remove the tape securing the lcd and microphone cables. 9 disconnect the lcd and microphone cables from their system board connectors. 10 if the notebook has a wireless card installed, note the antenna cable routing for later reference and then release t...

  • Page 91

    Www.Packardbell.Com 85 11 pull the antenna cables from underneath the computer and release them from the latches. 12 remove the top hinge screws securing the lcd assembly. 13 lift the lcd panel assembly up and away from the notebook..

  • Page 92

    Chapter 3: replacing notebook components 86 14 position the new lcd panel assembly on the notebook, and then secure it with the hinge screws removed in step 12 . 15 if the notebook has a wireless card installed, proceed to step 17 to arrange the antenna cables. 16 if there’s no wireless card install...

  • Page 93

    Www.Packardbell.Com 87 replacing the palm rest tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) to replace th...

  • Page 94

    Chapter 3: replacing notebook components 88 9 remove the 3 screws securing the palm rest to the base side. 10 disconnect the dc-in cable from the system and release the cable from the latches. 11 disconnect the left speaker cable from rear2 connector and release it from the latch..

  • Page 95

    Www.Packardbell.Com 89 12 disconnect the touchpad board and touchpad button board cables from tp335 and fp2 connectors. 13 carefully pry loose the palm rest from the system and lift the palm rest from the system. 14 place the new palm rest assembly on top of the base enclosure and press it down on a...

  • Page 96

    Chapter 3: replacing notebook components 90 replacing the touchpad board tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest...

  • Page 97

    Www.Packardbell.Com 91 9 remove the touchpad board cable from the palm rest. 10 note the orientation of the touchpad board for later reference in installing the new touchpad board..

  • Page 98

    Chapter 3: replacing notebook components 92 11 insert a small flat-blade screwdriver or non-marring scribe between the touchpad board and the palm rest’s underside, and carefully pry the board loose. 12 remove the touchpad board from the palm rest. 13 observing the same orientation as the old touchp...

  • Page 99

    Www.Packardbell.Com 93 18 reinstall the keyboard by following the instructions in “replacing the keyboard” on page 77 . 19 if you have disconnected any wireless antennas, reconnect them now. 20 replace the bay cover, then tighten the cover screws. 21 reinstall the battery..

  • Page 100

    Chapter 3: replacing notebook components 94 replacing the touchpad button board tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (pa...

  • Page 101

    Www.Packardbell.Com 95 8 disconnect the cable from the touchpad button board connector. 9 remove the touchpad button board from the palm rest. 10 replace the new touchpad button board on the palm rest. 11 connect the cable to the touchpad button board connector. 12 replace the screws that was remove...

  • Page 102

    Chapter 3: replacing notebook components 96 replacing the usb board tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - to...

  • Page 103

    Www.Packardbell.Com 97 7 disconnect the usb board cable from the usbcn1 on the system board and release the cable from the latch. 8 remove the usb board screw. 9 release from latch and remove the usb board from the base enclosure..

  • Page 104

    Chapter 3: replacing notebook components 98 10 place the new usb board in the base enclosure; fix it to the latch and secure it with the screw removed in step 8 . 11 connect the usb board cable to the new usbcn1 on the system board. 12 reinstall the palm rest by following the instructions in “replac...

  • Page 105

    Www.Packardbell.Com 99 replacing the bluetooth module tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) to rep...

  • Page 106

    Chapter 3: replacing notebook components 100 8 the bluetooth module is glued to the system board. Carefully pry loose the bluetooth module from the system board using a flat blade screw driver or a plastic scribe. 9 secure the new bluetooth module on the system board and connect the bluetooth cable ...

  • Page 107

    Www.Packardbell.Com 101 replacing the modem board tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) • 2 chrome...

  • Page 108

    Chapter 3: replacing notebook components 102 8 carefully lift up the modem board to remove it from the port on the system board; then turn it over to access the cable. 9 disconnect the cable from the modem board. 10 connect the cable to the new modem board and connect it to the port on the system bo...

  • Page 109

    Www.Packardbell.Com 103 replacing the coin-cell battery tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) to r...

  • Page 110

    Chapter 3: replacing notebook components 104 8 gently push down the new coin-cell battery to latch it into the system board. 9 reinstall the palm rest by following the instructions in “replacing the palm rest” on page 87 . 10 reinstall the lcd panel assembly by following the instructions in “replaci...

  • Page 111

    Www.Packardbell.Com 105 replacing the dc-in cable tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) to replace...

  • Page 112

    Chapter 3: replacing notebook components 106 9 reinstall the palm rest by following the instructions in “replacing the palm rest” on page 87 . 10 reinstall the lcd panel assembly by following the instructions in “replacing the lcd panel assembly” on page 83 . 11 reinstall the keyboard cover by follo...

  • Page 113

    Www.Packardbell.Com 107 replacing the system board tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (wireless card) • 1 chrome m2×4 (hard drive 1) • 1 chrome m2×4 (hard drive 2) • 1 chrome m2×4 (optical drive) • 2 black m2x4 (optional vga card) • 1 chrome m2x4 (...

  • Page 114

    Chapter 3: replacing notebook components 108 9 remove the cpu by following the instructions in “replacing the cpu” on page 73 . 10 if the system comes with a vga board, remove the vga board by following the instructions in “replacing the vga board (for discrete models)” on page 75 . 11 remove the ke...

  • Page 115

    Www.Packardbell.Com 109 21 remove the one screw securing the system board to the base panel. 22 carefully lift the right side of the system board and slide it out of the base panel. 23 replace the new system board into the base panel. 24 secure the new system board with the screws that was remove in...

  • Page 116

    Chapter 3: replacing notebook components 110 29 reconnect the usb board cable by following the instructions in “replacing the usb board” on page 96 . 30 replace the palm rest by following the instructions in “replacing the palm rest” on page 87 . 31 replace the lcd panel assembly by following the in...

  • Page 117

    Www.Packardbell.Com 111 replacing the left and right speakers tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (wireless card) • 1 chrome m2×4 (hard drive 1) • 1 chrome m2×4 (hard drive 2) • 1 chrome m2×4 (optical drive) • 2 black m2x4 (optional vga card) • 1 ch...

  • Page 118

    Chapter 3: replacing notebook components 112 4 remove the any adhesive tapes securing the speaker cables. 5 remove the 3 screws securing the left and right speaker to the base panel. 6 replace the new left and right speakers to the base panel. 7 secure the left and right speaker with the 3 screws th...

  • Page 119

    Www.Packardbell.Com 113 8 replace the system board by following steps 23 to 44 in “replacing the system board” on page 107 . 9 replace the bay cover, then tighten the cover screws. 10 reinstall the battery..

  • Page 120

    Chapter 3: replacing notebook components 114 replacing the subwoofer tools you need to complete this task: screws removed during this task: • 1 chrome m2×4 (wireless card) • 1 chrome m2×4 (hard drive 1) • 1 chrome m2×4 (hard drive 2) • 1 chrome m2×4 (optical drive) • 2 black m2x4 (optional vga card)...

  • Page 121

    Www.Packardbell.Com 115 4 remove the 2 screws securing the subwoofer to the base panel. 5 lift to remove the subwoofer from the base panel. 6 replace the new subwoofer on the base panel. 7 secure the new subwoofer with the 2 screws that was remove on step 4 . 8 replace the system board by following ...

  • Page 122

    Chapter 3: replacing notebook components 116 replacing the lcd front panel tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 black m2.5×8 (palm rest - base side) • 3 black m2.5×8 (palm re...

  • Page 123

    Www.Packardbell.Com 117 note: the lcd front panel is glued to the lcd panel by a double-sided adhesive tape. When replacing back the lcd front panel, don’t forget to replace the double-sided adhesive tape that might be destroyed while removing the it. 7 turn over the lcd front panel as shown. 8 remo...

  • Page 124

    Chapter 3: replacing notebook components 118 16 reinstall the battery..

  • Page 125

    Www.Packardbell.Com 119 replacing the inverter board tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) • 1 chr...

  • Page 126

    Chapter 3: replacing notebook components 120 8 turn over the inverter board to access the cables. 9 disconnect the cables from the inverter board. 10 connect the cables that was remove in step 9 to the new inverter board. 11 turn over the inverter board and secure it to the lcd panel lid with the sc...

  • Page 127

    Www.Packardbell.Com 121 replacing the lcd tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8 (palm rest - top side) • 1 chrome m2×3 (i...

  • Page 128

    Chapter 3: replacing notebook components 122 8 disconnect the cable from the webcam. 9 remove the 8 screws from the left and right hinges on the lcd. 10 remove the adhesive tape near the webcam area..

  • Page 129

    Www.Packardbell.Com 123 11 remove the lcd from the lcd assembly lid. 12 remove the 6 screws from the left and right lcd panel hinge brackets to remove it. 13 lay the lcd on its front to access the lcd cable..

  • Page 130

    Chapter 3: replacing notebook components 124 14 detach the portion of the lcd cable that is glued to the lcd panel. 15 detach the adhesive tape near the lcd cable connector. 16 disconnect the lcd cable from the connector..

  • Page 131

    Www.Packardbell.Com 125 17 connect the lcd cable to the connector on the new lcd panel and replace the tapes that might be destroyed when removing the lcd cable. 18 turn the lcd on its back and secure the left and right lcd bracket with that screws that were removed in step 12 . 19 place the new lcd...

  • Page 132

    Chapter 3: replacing notebook components 126 replacing the lcd panel hinge brackets tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8...

  • Page 133

    Www.Packardbell.Com 127 11 replace the inverter board by following the instructions in “replacing the inverter board” on page 119 . 12 replace the lcd front panel by following the instructions in “replacing the lcd front panel” on page 116. 13 reinstall the lcd panel assembly by following the instru...

  • Page 134

    Chapter 3: replacing notebook components 128 replacing the microphone tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8 (palm rest - ...

  • Page 135

    Www.Packardbell.Com 129 9 replace the new microphone into the lcd front panel. 10 replace the lcd front panel by following the instructions in “replacing the lcd front panel” on page 116. 11 reinstall the lcd panel assembly by following the instructions in “replacing the lcd panel assembly” on page ...

  • Page 136

    Chapter 3: replacing notebook components 130 replacing the webcam tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8 (palm rest - top ...

  • Page 137

    Www.Packardbell.Com 131 9 reconnect the cable to the webcam. 10 replace the lcd front panel by following the instructions in “replacing the lcd front panel” on page 116. 11 reinstall the lcd panel assembly by following the instructions in “replacing the lcd panel assembly” on page 83 . 12 reinstall ...

  • Page 138

    Chapter 3: replacing notebook components 132 replacing the antennas tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest - base side) • 3 black m2.5×8 (palm rest - to...

  • Page 139

    Www.Packardbell.Com 133 9 release the antenna cables from the aluminium adhesive tapes securing them and then carefully pry loose the left and right antennas. 10 secure the new antenna on the lcd assembly lid and route their cables underneath the adhesive tabs. 11 replace the lcd front panel by foll...

  • Page 140

    Chapter 3: replacing notebook components 134 replacing the lcd assembly lid tools you need to complete this task: tools you need to complete this task: screws removed during this task: • 2 black m2.5×8 (lcd panel hinges - bottom) • 2 black m2.5×8 (lcd panel hinges - top) • 13 m2.5×8 black (palm rest...

  • Page 141

    Www.Packardbell.Com 135 8 remove the lcd by following the instructions in step 8 to step 12 in “replacing the lcd” on page 121 . 9 place the lcd on the new lcd assembly lid and follow the instruction in “replacing the lcd” on page 121 to secure the lcd. 10 replace the lcd front panel by following th...

  • Page 142

    Chapter 3: replacing notebook components 136.

  • Page 143: •

    Chapter4 137 troubleshooting • diagnosing problems • system test procedures • power-on self-test (post) error message • index of error messages • phoenix bios beep codes • symptom-to-fru error messages • intermittent problems • undetermined problems.

  • Page 144

    Chapter 4: troubleshooting 138 diagnosing problems use the following procedure as a guide for diagnosing notebook problems. 1 obtain the failing symptoms in as much detail as possible. 2 verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the sam...

  • Page 145

    Www.Packardbell.Com 139 system test procedures testing the optical drive use the following procedure to isolate a problem in an optical drive controller, driver, or drive. To test the optical drive: 1 boot from the diagnostics diskette and start the diagnostics program. 2 run the cd-rom test and see...

  • Page 146

    Chapter 4: troubleshooting 140 testing the memory memory errors can stop your programs, show error messages on the screen, or hang the system. To test the memory: 1 boot from the diagnostics diskette and start the diagnostics program. 2 run the memory test and see if the test completes successfully....

  • Page 147

    Www.Packardbell.Com 141 • if the voltage is not correct, replace the power adapter. • if the voltage is within the range, do the following: – replace the system board. – if the problem is not corrected, see “undetermined problems” on page 157 . – if the power-on indicator does not light up, check th...

  • Page 148

    Chapter 4: troubleshooting 142 testing the touchpad if the touchpad doesn’t work, do the following actions one at a time to correct the problem. To test the touchpad: 1 reconnect the touchpad cables. 2 replace the touchpad. 3 replace the system board. After you use the touchpad, the pointer may drif...

  • Page 149

    Www.Packardbell.Com 143 power-on self-test (post) error message the post error message index lists the error message and their possible causes. The most likely cause is listed first. This index can also help you determine the next possible fru to be replaced when servicing a notebook. If the symptom...

  • Page 150

    Chapter 4: troubleshooting 144 index of error messages error codes error messages error codes error messages 006 equipment configuration error causes: 1. Cpu bios update code mismatch 2. Ide primary channel master drive error (the causes are shown before “equipment configuration error”) 010 memory e...

  • Page 151

    Www.Packardbell.Com 145 system battery is dead - replace and run setup test or replace the cmos battery, run the bios setup utility to reconfigure system time, then reboot the system. System cmos checksum bad - default configuration used test or replace the cmos battery, run the bios setup utility t...

  • Page 152

    Chapter 4: troubleshooting 146 no-beep error messages invalid system configuration data • test or replace the bios rom. • test or replace the system board. I/o device irq conflict • run “load setup defaults” using the bios setup utility, then reboot the notebook. • test or replace the cmos battery, ...

  • Page 153

    Www.Packardbell.Com 147 phoenix bios beep codes code beeps post routine description 02h verify real mode 03h disable non-maskable interrupt (nmi) 04h get cpu type 06h initialize system hardware 08h initialize chipset with initial post values 09h set in post flag 0ah initialize cpu registers 0bh enab...

  • Page 154

    Chapter 4: troubleshooting 148 2eh 1-3-4-3 ram failure on data bits xxxx of low byte of memory bus 2fh enable cache before system bios shadow 30h 1-4-1-1 ram failure on data bits xxxx of high byte of memory bus 32h test cpu bus-clock frequency 33h initialize phoenix dispatch manager 36h warm start s...

  • Page 155

    Www.Packardbell.Com 149 66h configure advanced cache registers 67h initialize multi processor apic 68h enable external and cpu caches 69h setup system management mode (smm) area 6ah display external l2 cache size 6bh load custom defaults (optional) 6ch display shadow-area message 6eh display possibl...

  • Page 156

    Chapter 4: troubleshooting 150 95h install cd rom for boot 96h clear huge es segment register 97h fixup multi processor table 98h 1-2 search for option roms. One long, two short beeps on checksum failure. 99h check for smart drive (optional) 9ah shadow option roms 9ch set up power management 9dh ini...

  • Page 157

    Www.Packardbell.Com 151 c2h initialize error logging c3h initialize error display function c4h initialize system error handler c5h pnpnd dual cmos (optional) c6h initialize notebook docking (optional) c7h initialize notebook docking late c8h force check (optional) c9h extended checksum (optional) d2...

  • Page 158

    Chapter 4: troubleshooting 152 f6h clear huge segment f7h boot to full dos code beeps post routine description.

  • Page 159

    Www.Packardbell.Com 153 symptom-to-fru error messages lcd power symptom / error action in sequence • the lcd backlight doesn't work. • the lcd is too dark. • the lcd brightness cannot be adjusted. • the lcd contrast cannot be adjusted. • run “load setup defaults” using the bios setup utility, then r...

  • Page 160

    Chapter 4: troubleshooting 154 memory card memory sound power management symptom / error action in sequence the notebook cannot detect the memory card. • test or replace the system board. Memory card reader slot pin is damaged. • test or replace the system board. Symptom / error action in sequence m...

  • Page 161

    Www.Packardbell.Com 155 devices keyboard and touchpad the battery fuel gauge in windows doesn’t go higher than 90%. • remove the battery pack and let it cool for two hours. • refresh the battery (use only battery power until the notebook turns off, then charge the battery). • test or replace the bat...

  • Page 162

    Chapter 4: troubleshooting 156 intermittent problems intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect. These reasons include: cosmic radiation, electrostatic discharge, or software errors. Fru replacement should be considered only...

  • Page 163

    Www.Packardbell.Com 157 undetermined problems if the diagnostic test may not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Use these procedures to isolate the failing fru (do not isolate a n...

  • Page 164

    Chapter 4: troubleshooting 158.

  • Page 165: •

    Chapter5 159 system board layout • easynote dt85 system board.

  • Page 166

    Chapter 5: system board layout 160 easynote dt85 system board top view number descriptions 1 hdmi port 2 vga port 3 ethernet lan port 4 line-in jack 5 mic-in jack 6 headphone-in jack 7 expresscard slot 8 coin-cell battery.

  • Page 167

    Www.Packardbell.Com 161 bottom view number descriptions 1 dimm slot 1 2 dimm slot 2 3 cpu socket 4 vga daughter board slot 5 5-in-1 card reader slot 6 hdd 1 connector 7 mini-card slot 8 wireless lan card slot.

  • Page 168

    Chapter 5: system board layout 162.

  • Page 169: •

    Chapter6 163 fru (field-replaceable unit) list • introduction • exploded diagram • fru list.

  • Page 170

    Chapter 6: fru (field-replaceable unit) list 164 introduction this chapter gives you the fru (field-replaceable-unit) listing in global configurations of this model. Refer to this chapter whenever ordering for parts to repair or for rma (return merchandise authorization). Please note that when order...

  • Page 171

    Www.Packardbell.Com 165 exploded diagram no. Part no. Description q'ty rev. Remark 1 60.4dw08.001 assy lcd panel imr 1x1 sjm80 1 a01 2 50.4dw08.001 sjm80 lcd cable single ht 1 a01 3 camera module 1 4 inverter module 1 5 lcd module 1 6 23.42274.001 microphone sjm80 xingmeng 1 7 33.4dw08.001 hinge l s...

  • Page 172

    Chapter 6: fru (field-replaceable unit) list 166 fru list category part name description part no. Adapter adapter 90w delta adp-90sb bbge blue lv4 led lf adp 90w 19v 3p adp-90sb bbge ap.09001.024 adpapter 90w 19v 3pin hipro hp-a0904a3 b1lf lv5 led lf blue adp 90w 19v 3p hp-a0904a3 b1lf ap.0900a.005 ...

  • Page 173

    Www.Packardbell.Com 167 touchpad synaptics tm00372-027 touchpad synaptics tm00372-027 56.Ayp01.001 multi-media board right capacitive button ns-sjm80-r v 55.Bcr01.002 multi-media board left capacitive button ns-sjm80-l v 55.Bcr01.003 wireless lan board 512an_mmwg shirley peak 5100 mm#895361 wlan 802...

  • Page 174

    Chapter 6: fru (field-replaceable unit) list 168 inverter board 18" darfon vk.22256.101 rev.B inverter dl vk.22256.101 rev.B 19.Ayp01.002 multi-media board cable right c.A. Mmb r ffc sjm80 tr 50.Bcr01.002 multi-media board cable right c.A. Mmb r ffc sjm80 jh 50.Bcr01.002 multi-media board cable left...

  • Page 175

    Www.Packardbell.Com 169 power cord 3a 250v 3pin uk code uk 2.5a 250v 3p bk 27.01518.541 power cord 5a 250v 3pin uk bk code 5a 250v 3p uk bk 27.03118.001 power cord 7a 125v 2pin japan code japan 7a 125v 2p bk 27.01518.551 power cord 10a 3pin bk denmark code denmark 2.5a 250v 3p bk 27.01518.561 power ...

  • Page 176

    Chapter 6: fru (field-replaceable unit) list 170 power cord aca / acnz power code aca / acnz annie 27.03218.021 power cord 7.5a 250v 3p australia bk code 7.5a 250v 3p australia bk 27.03218.051 power code 7a 125v 2pin japan code 7a 125v japan 2pin bk 27.03518.161 case/cover/bracket assembly new card ...

  • Page 177

    Www.Packardbell.Com 171 upper case black w/touchpad cable & touch pad button board cable w/o finger print hole assy ucase w/o fp sjm80 60.Bcr01.002 lower case w/dc-in cable & modem cable & speaker w/o tv hole assy lcase w/o tv sjm80 60.Bcr01.001 speaker speaker pack right & left speaker r&l sjm80 fg...

  • Page 178

    Chapter 6: fru (field-replaceable unit) list 172 dvd-rw super-multi module 8x sata odd nsm8xs super-multi drive 6m.Bcr01.001 odd toshiba super-multi drive 12.7mm tray dl 8x sata ts-l633b lf w/o bezel odd sm sata 12.7 tl ts-l633b ku.00801.030 odd hlds super-multi drive 12.7mm tray dl 8x gt20n lf w/o ...

  • Page 179

    Www.Packardbell.Com 173 cpu intel core2dual p7450 2.13g 3m 1066 tj novt ic cpu penryn p7450 2.13g pga kc.74501.Dpp cpu intel core2dual p7550 pga 2.26g 3m 1066 r-0 ic cpu penryn p7550 2.26g pga kc.75501.Dpp cpu intel core2dual p8600 2.4g 3m 1066 25w r-0 ic cpu penryn p8600 2.4g pga kc.86r01.Dpp cpu i...

  • Page 180

    Chapter 6: fru (field-replaceable unit) list 174 hdd 160gb 5400rpm 2.5" sata wd wd1600bevt-22zct0 fw:11.01a11 hdd 160gb wd wd1600bevt-22 zct0 kh.16008.022 hdd 2.5" 5400rpm 250gb seagate st9250315as wyatt sata lf f/w:0001sdm1 hdd 250gb seagate st9250315as kh.25001.016 hdd 250gb 5400rpm sata toshiba l...

  • Page 181

    Www.Packardbell.Com 175 hdd bracket assy 60 hdd brk bb2 33.Ayp01.002 heatsink cpu heatsink discrete w/fan assy thermal foxconn px sjm80 60.Bcr01.003 cpu heatsink uma w/fan assy thermal foxconn sjm80 60.Bc801.001 keyboard keyboard 100keys gp7t sjv70/sjv50 internal17 standard black french kb mp-07f36f...

  • Page 182

    Chapter 6: fru (field-replaceable unit) list 176 keyboard 100keys gp7t sjv70/sjv50 internal17 standard black portuguese kb mp-07f36p0-442 4h pt 100gp7t kb.I170g.102 keyboard 100keys gp7t sjv70/sjv50 internal17 standard black danish kb mp-07f36dk-442 4h dk 100gp7t kb.I170g.092 keyboard 100keys gp7t s...

  • Page 183

    Www.Packardbell.Com 177 keyboard 100keys gp7t sjv70/sjv50 internal17 standard black czech/slovak kb mp-07f36cs-442 4h czk100gp7t kb.I170g.090 keyboard 100keys gp7t sjv70/sjv50 internal17 standard black belgium kb mp-07f36b0-442 4h be 100gp7t kb.I170g.088 keyboard 100keys gp7t sjv70/sjv50 internal17 ...

  • Page 184

    Chapter 6: fru (field-replaceable unit) list 178 camera 1.0m suyin cn1014-s36b-ov01-1 camera 1m cn1014-s36b-o v01-1 57.Pcc01.002 lcd bracket right w/hinge hinge r sjm80 lh 33.Bcr01.001 lcd bracket right w/hinge hinge r sjm80 szs 33.Bcr01.001 lcd bracket left w/hinge hinge l sjm80 lh 33.Bcr01.002 lcd...

  • Page 185

    Www.Packardbell.Com 179 microphone microphone sjm80 xingmeng 23.Bcr01.003 microphone microphone sjm80 goertek 23.Bcr01.003 inverter board 18" darfon vk.21189.A01 inverter 18" vk.21189.A01 19.Ayp01.001 lcd/camera cable for single lamp c.A. Lcd single lamp sjm80 ht 50.Bcr01.004 lcd/camera cable for si...

  • Page 186

    Chapter 6: fru (field-replaceable unit) list 180 sodimm 1gb ddriii 1066mhz micron mt8jsf12864hy-1g1d1 sodimm 1g mt8jsf12864hy -1g1d1 kn.1gb04.003 sodimm 1gb ddriii 1066mhz elpida ebj11ue6bau0-ae-e lf 64*16 0.07um sodimm 1g ebj11ue6bau0- ae-e kn.1gb09.009 sodimm 1gb ddrlll 1066mhz elpida ebj11ue6bbs0...

  • Page 187

    Www.Packardbell.Com 181 screw m2.5x4l ni nylok scrw m2.5x4l ni nylok 86.00h36.534 screw m2*4 wafer ni scrw m2*4 wafer ni 86.9a552.4r0 screw m2.5*3 wafer ni scrw m2.5*3 wafer ni 86.9a553.3r0

  • Page 188

    Chapter 6: fru (field-replaceable unit) list 182.

  • Page 189

    Appendix a 183 model definition and configuration.

  • Page 190

    Appendix a: 184 easynote dt85 common to all model configurations are: • camera: 0.3m dv • card reader: 5-in-1 built-in • adapter: 65w • lcd: 15.6 wxga led-backlit model ro country acer part no description cpu vga chip vram 1 memory 1 memory 2 hdd 1(gb) odd wireless lan bluetooth battery entj65-424g3...

  • Page 191

    Www.Packardbell.Com 185 entj65-744g50b n ww ww s2.B610y.00 3 entj65-744g50bn vhb32bww1 n10mge1512cck8 2*2g/500_l/bt/6l2.8/5r /cb_n2_0.3d_gec_en1 1 c2dp7450 n10mge 1 512m- ddr2 (64*16 *4) so2g bii6 so2g bii6 n500gb5.4k s nbdcb4 xs sp1x2m mw bt 2.0 6cell2.8 entj65-744g50m n ww ww s2.B610y.00 2 entj65-...

  • Page 192

    Appendix a: 186 entj65-643g32m n emea portug al lx.B760x.00 1 entj65-643g32mn vhp32btpt1 umacck8 2g+1g/320/6l/5r/cb_n 2_0.3d_gec_pt44 easynote_tj65-bt-206 pt c2dt6400 uma n so2g bii6 so1g bii6 n320gb5.4k s nsm8xs sp1x2m mw n 6cell2.2 entj65-644g32m n emea portug al lx.B760x.00 2 entj65-644g32mn vhp3...

  • Page 193

    Www.Packardbell.Com 187.

  • Page 194

    Appendix a: 188.

  • Page 195: •

    Appendix b 189 test compatible components • introduction • microsoft® windows vista® environment test.

  • Page 196

    Appendix b: test compatible components 190 introduction this notebook’s compatibility is tested and verified by acer’s internal testing department. All of its system functions are tested under windows vista ® , windows ® xp home, windows ® xp pro environment. Refer to the following lists for compone...

  • Page 197

    Www.Packardbell.Com 191 microsoft ® windows vista ® environment test item specification crt port test crt monitor viewsonic 19" crt vcdts23283-2g monitor viewsonic professional series g220 21" monitor philips 109p 19” monitor mag 810ft ii 19” monitor lcd monitor viewsonic 19" lcd va1912w monitor vie...

  • Page 198

    Appendix b: test compatible components 192 usb game pad / joystick alps usb game pad microsoft sidewinder plug & play gamepad logitech freedom 2.4ghz cordless logitech wingman usb extreme digital 3d joystick microsoft usb side winder game pad saitek p2500 rumble force pad logitech wingman formula (w...

  • Page 199

    Www.Packardbell.Com 193 item specification multimedia card test sd/mini sd/micro sd card sandisk secure digital card 256mb a-data secure digital card 4gb 150x kingston sdhc 8gb class6 transcend sd 512mb transcend 150x ultra speed sd 4gb transcend sd hc 4gb a-data 150x turbo sd 4gb a-data minisd 512m...

  • Page 200

    Appendix b: test compatible components 194.

  • Page 201

    Appendix c 195 online support information.

  • Page 202

    Appendix c: online support information 196 online support information this appendix describes online technical support services available to help you repair your packard bell products. If you are a distributor, dealer, asp or tpm, please refer your technical queries to your local acer branch office....

  • Page 203

    197 index a ac adapter specifications 16 antennas, replace 132 application key 24 arrow keys 24 audio controller 7 next track 25 play/pause button 25 previous track 25 specifications 11 stop button 25 b backlight control 25 battery remove 54 specifications 16 bay cover remove 55 bios crisis disk 41 ...

  • Page 204

    Index 198 intermittent problems 156 internet chat programs 27 k key communication 22 keyboard keys 24 specifications 13 keyboard cover replace 77 keyboard or auxiliary input device check 139 keys application 24 arrow 24 directional 24 fn 24 function 24 hybrid sleep 25 navigation 24 sleep 25 system 2...

  • Page 205

    199 www.Gateway.Com play/pause button 25 previous chapter 25 stop button 25 volume mute 25 w webcam specifications 15 usage 27 windows key 24 wired lan specifications 14 wireless card replace 58 wireless lan specifications 14.

  • Page 206

    Index 200

  • Page 208

    Man sjv-80 svc gde r1 06/09.