Summary of EasyNote F5
Page 1
Disassembly manual.
Page 2
Packard bell easynote f5/f7 disassembly manual page 2 table of contents overview .................................................................................................................................................................................3 technician notes ..........................
Page 3
Packard bell easynote f5/f7 disassembly manual page 3 overview this document contains step-by-steps disassembly instructions for the easynote f5/f7 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that ar...
Page 4
Packard bell easynote f5/f7 disassembly manual page 4 hazardous voltage there is hazardous voltage present inside the computer when it is connect to an ac supply, even when the computer’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact...
Page 5
Packard bell easynote f5/f7 disassembly manual page 5 removing the battery perform the following steps to remove the battery: 1. Make sure to power off the easynote f5/f7. 2. Turn the unit upside down. 3. Unscrews the bottom cover door and slide it out of its place as the arrow shows in fig. 1 fig. ...
Page 6
Packard bell easynote f5/f7 disassembly manual page 6 removing the memory module to remove the memory module, first remove the battery (see removing the battery ), then perform the following steps: 1. Unclip the memory module as shown in fig. 3 fig. 3 removing the memory module 2. Remove the memory ...
Page 7
Packard bell easynote f5/f7 disassembly manual page 7 removing the hard disk drive to remove the hard disk drive, first remove the battery (see removing the battery ), then perform the following steps: 1. Remove the screws as shown in fig. 4 fig. 4 screw retaining the hdd module 2. Carefully pull th...
Page 8
Packard bell easynote f5/f7 disassembly manual page 8 removing the cpu to remove the cpu first remove the battery (see removing the battery ) then perform the following steps: 1. Unscrew screws on cpu heat sink as shown in fig. 6 fig. 6 cpu heat sink 2. Unlock the cpu from the cpu socket and lift up...
Page 9
Packard bell easynote f5/f7 disassembly manual page 9 removing the keyboard to remove the keyboard, first remove the battery (see removing the battery ), then perform the following steps: 1. Release the keyboard from the base unit by push kb lock with flat screws driver as shown in fig. 8 fig. 8 rel...
Page 10
Packard bell easynote f5/f7 disassembly manual page 10 removing the optical disk drive to remove the odd, first remove the battery (see removing the battery ) then perform the following steps: 1. Use pin to eject odd tray as shown in fig. 10 fig. 10 ejecting odd tray 2. Flip over the unit, unscrew a...
Page 11
Packard bell easynote f5/f7 disassembly manual page 11 removing the lcd module to remove the lcd module first remove the battery (see removing the battery ) then perform the following steps: 1. To remove hinge cover, apply pressure at both end of the hinge cover as shown in fig. 12 fig. 12 removing ...
Page 12
Packard bell easynote f5/f7 disassembly manual page 12 4. Release two screws at both side of lcd hinge, remain two outer screws attached. Fig. 15 removing screws at lcd hinge 5. Carefully separate the lcd module from the base unit. M3x7 black.
Page 13
Packard bell easynote f5/f7 disassembly manual page 13 removing the lcd panel to remove the lcd panel, first remove the lcd module (see removing the lcd module ), then perform the following steps: 1. Use a pin to remove the rubber cover on the lcd module as shown in fig. 16 2. Remove all screws as s...
Page 14
Packard bell easynote f5/f7 disassembly manual page 14 3. Carefully release lcd bezel form lcd module as shown in fig. 17 fig. 17 removing the lcd bezel 4. Release all screws in lcd module as shown in fig. 18 fig. 18 removing the screws at lcd module a = m3x4 silver b = m2.5x7 black c = m2x3.5 silve...
Page 15
Packard bell easynote f5/f7 disassembly manual page 15 5. Disconnect all cable on inverter board. Fig. 19 inverter board 6. Carefully lift up the lcd panel. 7. Remove the screws at both sides of the lcd panel in order to release the lcd hinges as shown in fig. 20 fig. 20 removing the lcd panel hinge...
Page 16
Packard bell easynote f5/f7 disassembly manual page 16 removing the bottom cover to remove the top cover , first remove the battery (see removing the battery ), remove the optical disk drive (see removing the optical disk drive ) then perform the following steps: 1. Remove all screws on the bottom o...
Page 17
Packard bell easynote f5/f7 disassembly manual page 17 removing the mdc modem to remove the mdc modem, first remove the bottom cover (see removing the bottom cover ) then perform the following steps: 1. Release screws and disconnect cable on mcd modem as shown in fig. 23 fig. 23 mdc modem 2. Lift up...
Page 18
Packard bell easynote f5/f7 disassembly manual page 18 removing the chipset heat sink to remove the chipset heat sink, first remove the bottom cover (see removing the bottom cover ), then perform the following steps: 1. Unscrew the screws on the chipset heat sink and disconnect the fan connector as ...
Page 19
Packard bell easynote f5/f7 disassembly manual page 19 removing the main board to remove the main board, first remove the battery (see removing the battery ), remove the hard disk drive (see removing the hard disk drive ), remove the cpu (see removing the cpu ), remove the optical drive (see removin...
Page 20
Packard bell easynote f5/f7 disassembly manual page 20 3. Pull the plastics part near to audio port outward to release main board. 4. Be careful when lifting up the main board. The metal plate next to vga port tends to block main board as shown in fig. 27 fig. 27 lifting up main board.
Page 21
Packard bell easynote f5/f7 disassembly manual page 21 removing the touch pad to remove the touch pad, first remove the main board (see removing the main board ) then perform the following steps: 1. Disconnect the touch pad and remove isolator stick on it as shown in fig. 28 fig. 28 touch pad 2. Uns...
Page 22
Packard bell easynote f5/f7 disassembly manual page 22 removing the speaker assembly to remove the speaker assembly, first remove the main board (see removing the main board ) then perform the following steps: 1. Remove the screws holding speaker assembly as shown in fig. 30 fig. 30 speaker assembly...
Page 23
Packard bell easynote f5/f7 disassembly manual page 23 screws m2.5x7 black m2.5x4.5 black m2.5x11.5 silver m2x7 black m2x4 silver m2x3.5 silver m3x4 silver m3x5 silver m2.5x10 silver m3x7 black.
Page 24
Packard bell easynote f5/f7 disassembly manual page 24 notice the information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent fr...