Summary of EasyNote L
Page 1
Packard bell easynote l disassembly manual.
Page 2: Table of Contents
1 packard bell easynote l disassembly manual table of contents overview 2 technician notes 2 disassembly instructions 2 reassembly instructions 2 required tools 2 hazardous voltage 3 avoid electrostatic discharge 3 power supply unit 3 removing the battery 4 removing the memory module 4 removing the ...
Page 3: Overview
2 packard bell easynote l disassembly manual overview this document contains step-by-step service instructions for the easynote l. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Packard bell reserves the right to make changes to the ea...
Page 4: Hazardous Voltage
3 packard bell easynote l disassembly manual hazardous voltage there is hazardous voltage present inside the computer when it is connected to an ac supply, even when the computer’ s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an au...
Page 5: Removing The Battery
4 packard bell easynote l disassembly manual removing the battery perform the following steps to remove the battery: i. Make sure to power off the easynote l. Ii. Disconnect the ac adapter and all peripherals. Iii. Turn the unit over. Iv. Unlock the battery and slide it out. Fig. 1 releasing the bat...
Page 6: Removing The Keyboard
Packard bell easynote l disassembly manual 5 fig. 3 releasing the memory side locks. Iii. Pull out the memory module from its slot. Removing the hard disk drive to remove the hard disk drive, first remove the battery (see removing the battery ), then perform the following steps: 1. Remove the 2 scre...
Page 7
Packard bell easynote l disassembly manual 6 1. Release the keyboard cover from the rear of the notebook. Fig. 6 releasing the keyboard cover. 2. Open the notebook and tilt the lcd module entirely backward. 3. Carefully remove the keyboard cover. Fig. 7 lifting the keyboard. 4. Pull the keyboard up ...
Page 8: Removing The Lcd Module
Packard bell easynote l disassembly manual 7 fig. 9 disconnecting the flat cable. Removing the optical disk drive to remove the optical disk drive, first remove the battery (see removing the battery ) and remove the keyboard (see removing the keyboard ), then perform the following steps: 1. Remove t...
Page 9
Packard bell easynote l disassembly manual 8 fig. 12 removing the heat plate screws. 2. Close the lcd, flip over the notebook and remove the 2 screws securing the lcd module. Fig. 13 removing the lcd module screws (bottom). 3. Remove the 2 screws on the back. Fig. 14 removing the lcd module screws (...
Page 10: Removing The Lcd Panel
Packard bell easynote l disassembly manual 9 5. Carefully lift the lcd module away from the unit. Removing the lcd panel to remove the lcd panel, first remove the lcd module (see removing the lcd module ), then perform the following steps: 1. Use a pin to remove the rubber covers on the lcd module. ...
Page 11
Packard bell easynote l disassembly manual 10 1. Remove the screws securing the heat plate (see fig. 12 ). 2. After taking out the heat plate, remove the 3 cpu fan screws, disconnect the cpu fan connector and remove the cpu fan. Fig. 19 location cpu fan screws. 3. Remove the 3 remaining screws on th...
Page 12: Removing The Top Cover
Packard bell easynote l disassembly manual 11 5. Take out the cpu very carefully. Note beware of the screws you use on the cpu heat sink! Make sure to use the original screws, otherwise it might cause damage to the cpu die. Note use extra care when unlocking or locking the cpu socket because the scr...
Page 13: Removing The Touchpad
Packard bell easynote l disassembly manual 12 fig. 23 location top cover screws. 4. Disconnect the touchpad connector and remove the flat cable (same principle as described in fig 9 ). Fig. 24 disconnecting the touchpad cable. 5. Carefully lift the top cover. Removing the touchpad to remove the touc...
Page 14: Removing The Wlan Card
Packard bell easynote l disassembly manual 13 fig. 25 location touchpad screws. 2. Carefully separate the touchpad module from the top cover. Removing the chipset heat sink to remove the chipset heat sink, first remove the top cover (see removing the top cover ), then perform the following steps: 1....
Page 15: Removing The Mdc Modem
Packard bell easynote l disassembly manual 14 fig. 27 releasing the wlan side locks. 2. Carefully take out the wlan card from the slot. Removing the mdc modem to remove the modem, first remove the top cover (see removing the top cover ), then perform the following steps: 1. Remove the 2 screws secur...
Page 16
Packard bell easynote l disassembly manual 15 fig. 29 screw location on the hdd holder. 3. Disconnect the speaker and lid switch connectors from the main board and remove the screws encircled in the following picture. Fig. 30 screws and connectors on main board. 4. Lift the main board and remove it ...
Page 17: Notice
16 packard bell easynote l disassembly manual notice the information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from nec co...