1. DL manuals
  2. Packard Bell
  3. Laptop
  4. EasyNote T5 SEries
  5. Disassembly Manual

Packard Bell EasyNote T5 SEries Disassembly Manual

Summary of EasyNote T5 SEries

  • Page 1

    Easynote t5 series disassembly manual nec computers international b.V. Easynote t5 series disassembly manual revision: 2.1 date: march 2005 for packard bell a division of nec computers international b.V..

  • Page 2

    Packard bell easynote t5 disassembly manual page 2 table of contents overview........................................................................................................................................................................3 technician notes .......................................

  • Page 3

    Packard bell easynote t5 disassembly manual page 3 overview this document contains step-by-step disassembly instructions for the easynote t5 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are remov...

  • Page 4

    Packard bell easynote t5 disassembly manual page 4 hazardous voltage there is hazardous voltage present inside the computer when it is connected to an ac supply, even when the computer’ s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact...

  • Page 5

    Packard bell easynote t5 disassembly manual page 5 removing the battery perform the following steps to remove the battery: 1. Make sure to power off the easynote t5 first. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in fig. 1 fig. 1 removing t...

  • Page 6

    Packard bell easynote t5 disassembly manual page 6 fig. 3 disconnecting the hard disk drive 3. Unscrew the four screws on both sides of the hard disk drive as shown in fig. 4 fig. 4 unscrewing the hard disk drive bracket screws removing the mdc modem module to remove the mdcmodem module, first remov...

  • Page 7

    Packard bell easynote t5 disassembly manual page 7 removing the keyboard cover to remove the keyboard cover , first remove the battery (see removing the battery ), then perform the following steps: 1. Remove the screw as shown in fig. 6 fig. 6 removing keyboard cover screws 2. Remove the keyboard co...

  • Page 8

    Packard bell easynote t5 disassembly manual page 8 1. Remove the screws as shown in fig. 8 fig. 8 removing the screws holding the keyboard note: the screw “a” located on the hard disk slot cover holds the hard disk drive and the keyboard. 2. Carefully lift up the keyboard. 3. Release the keyboard fp...

  • Page 9

    Packard bell easynote t5 disassembly manual page 9 fig. 10 removing the screws on heat plate note: if you want to disassemble the optical drive, you are required to release screw “a” only. 2. Push the optical drive module out from the base unit as shown in fig. 11 fig. 11 pushing optical drive modul...

  • Page 10

    Packard bell easynote t5 disassembly manual page 10 fig. 12 removing heat plate from base unit note: when assembling the heat plate, make sure that these three hocks on the heat plate are properly inserted into the openings located on the top cover. Removing the memory module to remove the memory mo...

  • Page 11

    Packard bell easynote t5 disassembly manual page 11 removing heat plate ), then perform the following steps: 1. Disconnect the wireless antenna connectors as shown in fig. 14 fig. 14 disconnecting the wireless antenna note: you might consider disconnecting the touch pad flat cable before removing th...

  • Page 12

    Packard bell easynote t5 disassembly manual page 12 fig. 16 removing the heat sink 3. Use flat screws driver to release the cpu from the cpu socket; carefully lift up the cpu and put it in a safe place. Fig. 17 releasing the cpu removing the lcd module to remove the lcd module, first remove the keyb...

  • Page 13

    Packard bell easynote t5 disassembly manual page 13 1. Unscrew the two lcd connector screws and also, disconnect the speaker connector as shown in fig. 18 fig. 18 disconnecting the lcd & speaker connectors 2. Remove the lcd cable cover with a small flat screws driver as shown in fig. 19 . Fig. 19 re...

  • Page 14

    Packard bell easynote t5 disassembly manual page 14 4. Unscrew the two screws located on the bottom of the unit as shown in fig. 21 fig. 21 lcd hinge screws at the bottom 5. Carefully lift the lcd module out of the system and put it aside. Removing the lcd panel to remove the lcd panel, first remove...

  • Page 15

    Packard bell easynote t5 disassembly manual page 15 fig. 22 screws on the lcd module 2. Relase the lcd bezel carefully and put it aside as shown in fig. 23 fig. 23 removing the lcd bezel 3. Unscrew all screws encircled in fig. 24 disconnect the inverter board and put it aside. A = m2x3.5 silver b= m...

  • Page 16

    Packard bell easynote t5 disassembly manual page 16 fig. 24 removing the inverter board screws 4. Carefully lift up lcd panel and disconnect the lcd cable from the penal. 5. Remove the screws at both sides of the lcd panel in order to release the lcd hinges as shown in fig. 25 . Fig. 25 removing the...

  • Page 17

    Packard bell easynote t5 disassembly manual page 17 to remove the top cover, first remove the keyboard cover (see removing the keyboard cover ), remove the keyboard (see removing the keyboard ), remove the lcd module (see removing the lcd module ) then perform the following steps: 1. Disconnect the ...

  • Page 18

    Packard bell easynote t5 disassembly manual page 18 fig. 28 battery compartment 5. Carefully lift up and release the top cover and put it aside. Fig. 29 removing the top cover note: remember to disconnect the touch pad cable before lifting up the top cover. On the vga connector area use extra care t...

  • Page 19

    Packard bell easynote t5 disassembly manual page 19 1. On the other side of the top cover unscrew the two screws on the touch pad assembly as shown in fig. 30 and remove the touch pad assy from the palm rest. Fig. 30 touch pad assembly removing the dc/dc board to remove the dc/dc board, first remove...

  • Page 20

    Packard bell easynote t5 disassembly manual page 20 fig. 31 dc/dc board 2. Carefully remove the dc/dc board as shown in fig. 32 and put it aside. Fig. 32 removing the dc/dc board removing the main board to remove the main board, first open the top cover (see removing the top cover ), remove dc/dc bo...

  • Page 21

    Packard bell easynote t5 disassembly manual page 21 fig. 33 removing the main board screws 2. Disconnect the vga connector from the base as shown in fig. 34 fig. 34 disconnecting the vga connector 3. Lift the main board out of the system and put it aside (fig. 35 ). A = m2x5 silver b = m2.5x8 silver...

  • Page 22

    Packard bell easynote t5 disassembly manual page 22 fig. 35 removing main board dip switch settings dip switch description seeting keyboard select1 keyboard select2 on : enable off: normal (default) on : connect to gnd off : nc password override. On: override off: available (factory setting) refer t...

  • Page 23

    Packard bell easynote t5 disassembly manual page 23 screws m2.5x5.6 silver m2.5x3.5 silver m2.5x8 sliver m2.5x10 silver m2.5x11 black m2.5x12.5 silver m2.5x15 black m2x3 sliver m2x6 black m3x4 black m2.5x5 sliver.

  • Page 24

    Packard bell easynote t5 disassembly manual page 24 disclaimer the information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent f...