1. DL manuals
  2. Palmgren
  3. Power Tool
  4. 80150
  5. Operating Manual And Parts List

Palmgren 80150 Operating Manual And Parts List

Manual is about: 12" Bench Model Drill Press

Summary of 80150

  • Page 1

    Operating manual & parts list 80150 12 ″ bench model drill press read carefully and follow all safety rules and operating instructions before first use of this product. 35285.09-1011.

  • Page 2

    Description palmgren drill presses feature a heavy cast iron base, column collar, work table and head. Work table height is adjustable using rack and pinion. Table can be tilted 45° both right and left, and rotates 360° on a vertical axis. Work table surface is precision ground and features t-slots ...

  • Page 3

    3 work area should be ready for job • keep work area clean. Cluttered work areas and work benches invite accidents. • do not use power tools in dangerous environments. Do not use power tools in damp or wet locations. Do not expose power tools to rain. • work area should be properly lighted. • proper...

  • Page 4

    4 install chuck refer to figure 8. • be sure spindle and chuck tapers are clean and dry. Make sure quill is completely retracted. • use the provided chuck key (ref. No. 13) to adjust the jaws of the chuck (ref. No. 12) until they are recessed inside the drill chuck body. • slide chuck over spindle t...

  • Page 5

    Extension cords • the use of any extension cord will cause some drop in voltage and loss of power. • wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage. • use the table to determine the minimum wire size (a.W.G.) extension cord. • use only 3-wir...

  • Page 6

    • use only the self-ejecting chuck key (ref. No. 13) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury. Digital display panel refer to figure 6. • display panel ‘a’...

  • Page 7

    7 maintenance warning: turn switch off and remove plug from power source outlet before maintaining or lubricating your drill press drive belt replace drive belt when worn. Lubrication refer to figures 7 and 8. The ball bearings are lubricated at the factory and need no further lubrication. Using 20w...

  • Page 8

    8 symptom spindle does not turn noisy spindle noisy operation bit burns or smokes excessive drill runout or wobble drill bit binds in workpiece possible causes 1. No power to drill press 2. Defective switch 3. Defective motor defective bearings 1. Incorrect belt tension 2. Dry spindle 3. Loose spind...

  • Page 9: Service Record

    9 palmgren operating manual & parts list 80150 service record palmgren 12 ″ bench model drill press date maintenance performed replacement parts required.

  • Page 10

    10 palmgren operating manual & parts list 80150 11 19 10 8 12 18 6 5 4 15 16 17 7 21 22 20 13 14 2 3 9 1 figure 7 – repair parts illustration for base.

  • Page 11

    11 palmgren operating manual & parts list 80150 replacement parts list for base * standard hardware item available locally. ∆ not shown. Key no. Description part no. Qty. 1 base 32505.00 1 2 8-1.25 x 125mm hex head bolt * 2 3 8mm flat washer * 2 4 8mm lock washer * 2 5 8-1.25mm hex nut * 2 6 8-1.25 ...

  • Page 12

    12 palmgren operating manual & parts list 80150 6 34 35 33 31 30 32 7 8 9 10 11 12 13 22 20 21 25 29 26 28 27 24 4 5 23 23 23 2 1 3 19 18 18 17 16 14 15 figure 8 – repair parts illustration for spindle and drive.

  • Page 13

    13 palmgren operating manual & parts list 80150 replacement parts list for spindle and drive * standard hardware item available locally. ∆ not shown. Key no. Description part no. Qty. 1 spindle nut 32519.00 1 2 spindle pulley 32520.00 1 3 upper spindle assembly 32521.00 1 4 circlip 32522.00 2 5 1/2”...

  • Page 14

    14 palmgren operating manual & parts list 80150 figure 9 – repair parts illustration for head 35 23 14 13 29 36 20 30 4 39 7 6 9 8 28 43 5 3 3 3 3 3 7 3 2 1 22 33 34 26 11 37 38 42 12 27 32 25 21 31 7 19 18 17 15 16 24 40 10 41.

  • Page 15

    1 speed sensor assembly 32543.00 1 2 5mm flat washer * 2 3 5-0.8 x 10mm pan head screw * 7 4 clamp 32564.00 1 5 seal 32565.00 1 6 plate 32566.00 1 7 clamp 32567.00 3 8 knob assembly 32544.00 1 9 pulley housing 32545.00 1 10 8-1.25mm fiber hex nut * 1 11 8mm flat washer * 1 12 8-1.25 x 45mm hex head ...

  • Page 16

    Warranty palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose oth...