1. DL manuals
  2. Palmgren
  3. Drill
  4. 80155
  5. Operating Manual

Palmgren 80155 Operating Manual

Manual is about: 15" heavy duty bench and floor model drill press

Summary of 80155

  • Page 1

    Operating manual & parts list 80155 and 80156 15″ heavy duty bench and floor model drill press read carefully and follow all safety rules and operating instructions before first use of this product. 32111.09-0910

  • Page 2

    Description palmgren drill presses feature a heavy cast iron base, column collar, work table and head. Work table height is adjustable using rack and pinion. Table can be tilted 45° both right and left, and rotates 360° on a vertical axis. Work table surface is precision ground and features t-slots ...

  • Page 3

    3 • arsenic and chromium from chemically-treated lumber. Your risk from these exposures vary, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. Always wear osha/niosh approved, properly...

  • Page 4

    4 mount table (80156) refer to figure 7. • attach crank handle (ref. No. 22) to shaft of worm gear (ref. No. 20), rotate worm gear to remove slack, and shoulder crank han- dle with set screw (ref. No. 21). Attach crank handle knob (ref. No. 23) to handle. • slide table (ref. No. 13) into hole in tab...

  • Page 5

    Warning: this work should be performed by a qualified electrician. A temporary 3-prong to 2-prong grounding adapter (see figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded. Do not use a 3-prong to 2-prong grounding adapter unless permit- ted by local and nati...

  • Page 6

    • rotation of work table : loosen table locking handle (ref. No. 18) and rotate table (ref. No. 13) to desired position and retighten handle. • tilting work table: loosen table bolt (ref. No. 10). Remove pin and nut (ref. No. 9). To do this, tighten nut until pin slips out easi- ly. Tilt table to de...

  • Page 7

    7 maintenance warning: turn switch off and remove plug from power source outlet before maintaining or lubricating your drill press drive belt replace drive belt when worn. Lubrication refer to figures 7 and 8. The ball bearings are lubricated at the factory and need no further lubrication. Using 20w...

  • Page 8

    8 symptom spindle does not turn noisy spindle noisy operation bit burns or smokes excessive drill runout or wobble drill bit binds in workpiece possible causes 1. No power to drill press 2. Defective switch 3. Defective motor defective bearings 1. Incorrect belt tension 2. Dry spindle 3. Loose spind...

  • Page 9: Service Record

    9 palmgren operating manual & parts list 80155 and 80156 service record palmgren 15 ″ bench and floor model drill presses date maintenance performed replacement parts required.

  • Page 10

    11 19 10 8 12 18 6 5 4 15 16 17 7 21 23 22 20 13 14 2 3 9 1 10 figure 7 - replacement parts illustration for base palmgren operating manual & parts list 80155 and 80156.

  • Page 11

    11 palmgren operating manual & parts list 80155 and 80156 replacement parts list for base * standard hardware item available locally. Δ not shown. Ref. Part numbers for: no. Description 80155 80156 qty. 1 base 32172.00 32177.00 1 2 8-1.25 x 125mm hex head bolt * * 2 3 8mm flat washer * * 4 4 8mm loc...

  • Page 12

    6 49 34 35 39 38 38 33 31 30 32 7 8 9 10 11 12 13 22 20 21 25 29 26 28 27 24 47 43 4 4 5 5 45 44 46 50 51 52 55 57 56 54 53 42 41 40 37 36 23 2 1 3 19 18 17 16 14 15 48 48 12 palmgren operating manual & parts list 80155 and 80156 figure 8 - replacement parts illustration for spindle and drive.

  • Page 13

    13 palmgren operating manual & parts list 80155 and 80156 ref. No. Description part no. Qty. 1 spindle nut 32126.00 1 2 spindle pulley 32127.00 1 3 spindle sleeve 32128.00 1 4 circlip 32129.00 2 5 6205-2rs ball bearing 09624.00 2 6 spacer 32130.00 1 7 front drive belt 32180.00 1 8 center pulley asse...

  • Page 14

    14 palmgren operating manual & parts list 80155 and 80156 figure 9 - replacement parts illustration for head 35 23 14 13 29 36 20 30 4 39 7 6 9 8 28 43 5 3 2 1 22 33 34 26 11 37 38 44 42 12 27 32 27 25 21 31 7 7 19 18 17 15 16 24 40 10 41.

  • Page 15

    Ref. No. Description part no. Qty. 1 knob assembly 32037.00 1 2 pulley housing 32183.00 1 3 grommet 32041.00 1 4 speed sensor assembly 32042.00 1 5 bracket 32043.00 1 6 5mm flat washer * 2 7 5-0.8 x 10mm pan head screw * 2 8 4mm flat washer * 2 9 4-0.7 x 10mm socket head bolt * 2 10 6-1.0 x 12mm che...

  • Page 16

    Warranty palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose oth...