Palmgren 82064 Operating Manual & Parts List - page 3
3
A
AS
SS
SE
EM
MB
BL
LY
Y
Parts to be fastened to the unit should be located and accounted
for (See List and Figure 1).
IMPORTANT: Do not attempt assembly if parts are missing. Use
this manual to order replacement parts.
A
5
/
16
-18 x 1
1
/
2
” Carriage bolt, 2 each
B Tool rest bracket, 2 each
C *
3
/
8
” Flat washer, 4 each
D *
3
/
8
”-16 Hex nut, 4 each
E Tool rest, 2 each
F
5
/
16
” Flat washer, 2 each
G
5
/
16
”-18 Hex nut, 2 each
H *
3
/
8
-16 x 1¼” Hex bolt, 4 each
I
Knob, 2 each
J
Spark guard, 2 each
K Eyeshield, 2 each
L Lower eyeshield bracket, 2 each
M Upper eyeshield bracket, 2 each (left and right)
N #10-24 x
3
/
8
” Pan head screw, 4 each
O 6-1.0 x 12mm” Flange screw, 2 each
P 6mm Flat washer, 2 each
Q Spacer, 2 each
R Dust collector hose (not shown)
NOTE: Parts marked with an asterisk (*) are mounted to the
grinder at the factory.
TOOL REST ASSEMBLY
• Slide
5
/
16
-18” carriage bolt (A) into square hole in tool rest bracket
(B). Slide spacer (Q) onto carriage bolt. Slide carriage bolt with
bracket into hole on inside of tool rest (E) as shown in Figure 1.
Slide
5
/
16
” flat washer (F) and
5
/
16
”-18 hex nut (G) onto carriage bolt.
Tighten nut finger tight.
• Remove
3
/
8
” hex nut (D) and flat washer (C) from
3
/
8
-16 x 1¼” hex
bolt (H) mounted to bottom front of left wheel guard.
• Slide slot in tool rest bracket over
3
/
8
” bolt. Replace flat washer
and hex nut. Position tool rest so that distance between tool
rest and grinding wheel is less than
1
/
16
”. Secure all nuts and bolts.
• Mount right tool rest in a similar manner.
EYESHIELD ASSEMBLY
• Remove
3
/
8
” hex nut (D) and
3
/
8
” flat washer (C) from
3
/
8
-16 x 1¼”
hex bolt (H) mounted to top front of left wheel guard.
• Slide slot in spark guard (J) over hex bolt and replace washer
and hex nut.
• Remove pan head screws (N) from eyeshield assembly. Mount
left upper eyeshield bracket (M) to eyeshield using pan head
screws and lower eyeshield bracket.
NOTE: Left upper eyeshield bracket is stamped “L” for identification.
• Slide 6-1.0 x 12mm flange screw (O) and 6mm flat washer (P)
through left upper eyeshield bracket (M) and through hole at
top of left spark guard (J) and secure with knob (I).
• Locate eyeshield in desired position for protecting operator
and secure all nuts and bolts.
• Mount right eyeshield assembly in a similar manner.
DUST COLLECTOR HOSE
• A dust collector hose has been provided with grinder. Slide
hoses onto sides of T-connector and flanges. Mount the hose
by sliding the flanges at each end over the exhaust ports on
the left and right wheel guards. Attach 2½” shop vacuum hose
to collector hose. Be sure hose is mounted securely.
DANGER:
Be sure to empty shop vacuum of all flammable materi-
al (flammable liquids and vapors, paper, wood, plastic, etc.) before
connecting vacuum to grinder. Hot sparks from grinder may ignite
flammable materials in shop vacuum.
IIN
NS
ST
TA
AL
LL
LA
AT
TIIO
ON
N
MOUNT GRINDER
• Mount grinder to a solid horizontal surface (hardware not pro-
vided). If mounted to metal pedestal, align mounting holes
with corresponding holes in pedestal. Insert a
1
/
4
-20 x 1¼” hex
head bolt with flat washer through base of grinder. From bot-
tom of pedestal, place a
1
/
4
” flat washer and
1
/
4
”-20 hex nut onto
the bolt. Tighten only until space between grinder base and
pedestal is
1
/
8
”. Using second nut on each bolt, jam tighten
against the first to prevent loosening by vibration.
• To mount grinder to wooden bench top, use
1
/
4
x 1¼” wood
screws with flat washers beneath heads. Tighten screws until
space between grinder base and bench top is
1
/
8
”.
GROUNDING INSTRUCTIONS
WARNING:
Improper connection of equipment grounding con-
ductor can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electrical shock.
• Check with a qualified electrician if grounding instructions are
not understood or if in doubt as to whether the tool is properly
grounded.
• This grinder is equipped with an approved 3-conductor cord
rated at 300V and a 3-prong, grounding type plug (See Figure
2) for your protection against shock hazards.
Palmgren Operating Manual & Parts List
82064
Figure 1 – Left Tool Rest and Eyeshield Assembly
J
G
M
N
O
P
D
C
C
B
D
E
F
A
L
I
K
H
Figure 2 – 3-Prong Receptacle
Properly Grounded Outlet
Grounding Prong
3-Prong Plug
Q