Operating manual & parts list 82088 combination grinder/sander read carefully and follow all safety rules and operating instructions before first use of this product. 37115.00-0213.
2 palmgren operating manual & parts list 82088 description palmgren combination grinder/sander is used for grinding, debur- ring, squaring, polishing and finishing metals, woods and plastics. Grinder/sander has a totally enclosed, fan-cooled direct drive motor. Belt housing swivels from vertical to ...
3 safety rules (continued) • keep children out of the workplace. Make workshop childproof. Use padlocks, master switches or remove switch keys to pre- vent any unauthorized use of power tools. Tool should be maintained • always unplug tool prior to inspection. • consult manual for specific maintaini...
4 assembly (continued) • slide 1/4-20 x 1/2” knob (l) through hole at top of left spark guard (m) into upper eyeshield bracket (h) and secure in position. • locate eyeshield in desired position for protecting operator and secure all knobs and bolts. Installation refer to figures 4, 5 6 and 7. Warnin...
5 installation (continued) • running the unit on voltages which are not within ±10% of the specified voltage may cause overheating and motor burn-out. • use the table to determine the minimum wire size (a.W.G.) extension cord. • use only 3-wire extension cords having 3-prong grounding type plugs and...
6 palmgren operating manual & parts list 82088 operation (continued) • note the original bevel angle on the item to be sharpened and try to maintain that angle. Sharpening a cutting edge requires removing burrs from edge. • deburring edge is done best by using the grinder to pull burr from edge acro...
7 palmgren operating manual & parts list 82088 symptom possible cause(s) corrective action motor will not start motor will not start; fuses blown or circuit breakers tripped motor fails to develop full power (power output of motor decreases rapidly with decrease in voltage at motor terminals) motor ...
8 palmgren operating manual & parts list 82088 2 2 26 21 23 20 18 18 37 39 40 36 35 34 33 32 31 24 30 36 38 41 15 16 19 22 29 22 25 24 14 1 17 11 6 13 7 12 3 28 27 4 5 9 9 8 10 figure 8 – repair parts illustration for belt housing.
9 1 5/16-18 x 1” knob 25812.00 1 2 5/16” flat washer * 3 3 tool rest 28670.00 1 4 3/8-16 x 1/2” knob 25817.00 1 5 3/8” flat washer * 1 6 bracket 31459.00 1 7 5/16-18 x 1” socket head bolt * 1 8 lower guard 28664.00 1 9 #10-24 x 1/4” flange screw 03210.00 7 10 abrasive belt (80 grit) 30788.00 1 11 ke...
10 palmgren operating manual & parts list 82088 2 26 21 23 20 15 15 18 1 16 16 17 38 39 35 36 37 32 34 33 31 30 40 29 29 29 29 29 22 25 24 19 14 41 42 43 9 6 11 8 13 13 7 8 12 3 28 27 4 4 5 8 10 figure 9 – repair parts illustration for grinding wheel and motor.
11 palmgren operating manual & parts list 82088 1 #10-24 x 7/8” pan head screw * 5 2 wheel guard cover 24496.02 1 3 5/8”-11 hex nut (lh) 00088.00 1 4 wheel flange 24497.00 2 5 grinding wheel (36 grit) 02037.00 1 6 switch 08066.01 2 7 upper eye shield bracket (left) 25177.00 1 8 eye shield kit 32290....
Palmgren operating manual & parts list 82088 warranty palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or...
