Palram 700492 Assembly Instructions Manual

Manual is about: LEAN-TO Greenhouse

Summary of 700492

  • Page 1

    Overall dimensions including base (approx) we strongly recommend the use of work gloves during assembly . Do not attempt to assemble the greenhouse in windy or wet conditions. Do not touch overhead power cables with the aluminum profiles. Always wear shoes and safety goggles when working with extrud...

  • Page 2: C O N T E N T S

    C o n t e n t s item qty. Mm/inc. Item qty. Mm/inc. Item qty. A701 1190mm/46.85” a702 670mm/26.38” 1 1 a711 1200mm/47.24” a712 200mm/47324” a715 680mm/26.77” a716 680mm”26.77” 1 1 1 1 a731 1233mm/48.54” 1 a741 1233mm/48.54” 1 a791 615mm/24.21” 2 a721 1472mm/57.92” a722 1472mm/57.92” 1 1 a761 1233mm/...

  • Page 3

    745 746 a b 447 747 c 412 412 a761 1 assembly of base profiles: be sure to bend the profiles into 90 , and to tighten firmly with screws 447. Qty 1 #a761 qty qty 1 #m747 1 #m745 1 #m746.

  • Page 4

    Assembly of the corners profiles a711 & a712: pay attention to set the profiles accordind to the detraction shown on the profiles a711 during the assembly of profile a761. Note: all nuts 412 should be on the inside of the stretcher,insert the screws 411 from the outside inwards. Do not fastern the s...

  • Page 5

    Assembly of profile a754: be sure to use the lower hall of existing two. Assembly of the gutter a731 (the profile also includes the door track): be sure to locate the gutter as shown in the illustration. A253 a754 411 412 a754 5 4 qty 2 #a754 qty 1 #a731 a731 412 a731 411.

  • Page 6

    Assembly of profile a715 and a716: connect the profiles as shown in the illustration. Assembly of the a741 profiles: connect the profile on both ends to profiles: a715 and a716, and mark the connecting points (to the wall), using the pre-drilled halls in the profile. A716 a715 a715 411 412 411 411 7...

  • Page 7

    412 a702 411 411 a702 10 assembly of profile a702 on the roof: connect the proile to profiles a741 on one side , and a731 on the second side. Assembly of profile a701 on the front wall: connect the profile to the profile a731 on one sideand to profile a761 on the second side. A701 412 411 a701 412 4...

  • Page 8

    Door sub-assembly: insert rubber seal r303 into profiles a771. It is advisable to use small amount of tender appropriate lubrication material. Connect profiles a771 with profiles a791 using screws 421. 411 door sub- assembly (continued): lay panel p502. Be sure to insert both ends into the channel i...

  • Page 9

    Connect plastic strips p332 on both sides of panel p502. Note: it is imperative to thread in the plastic strips.Onto the aluminum profiles in it’s assigned position. See illustrations a to d. Door sub-assembly (continued): connect all four plastic rollers p304 using screws 421 and nuts 422. A b c c ...

  • Page 10

    A731 412 411 a761 assembly of the door to wall panels: slid the door unto the track on frofile a731 (gutter), and on the same time on proffile a761. Insert two screws, 411& nuts 412 on both ends of profile a731. Assembly noise reduction profile p317 to wall panels. P317 p317 15 14 qty 3 #p317 qty 1 ...

  • Page 11

    Connect plastic strips p331and p330. See illustations a to d. Lay panel p501. Be sure to insert upper and into the channel in profile a731 and frofiles a754. P501 p501 p501 p331 p330 17 16 qty qty 3 #p501 2 #p330 4 #p331 a b c d.

  • Page 12

    18 apply roof panel p520 and triangle panels p521&p522. Connect plastic strips p334. See illustrations a to d at step #17. P333 p521 p522 p520 p334 p334 19 18 assembly follows illustration. Qty qty p316 p316 p316 p520 1 #p316 1 #p520 2 #p333 2 #p334 qty 1 #p521 1 #p522 qty.

  • Page 13

    Qty 412 412 a782 a782 a751 411 411 411 411 a752 a307 p519 p302 412 422 vent sub-assembly: apply profiles a782,a751,a752 and assemble according to the illustration using screws and nuts 411, 412. Assembly follows illustration. 21 20 qty 1 #a751 1 #a752 2 #a782 qty 1 #p519.

  • Page 14

    Fasten all screws and nuts of your lean-to greenhouse. M307 23 22 qty 2 #m307.