1. DL manuals
  2. Palram
  3. Lawn and Garden Equipment
  4. 701550
  5. Assembly Instructions Manual

Palram 701550 Assembly Instructions Manual

Manual is about: EuroStyle 6’X8’ Greenhouse 255x193x203 cm / 100”X76”X80”

Summary of 701550

  • Page 1

    Catalog no. 66163 * version #3 eurostyle 6’x8’ greenhouse 255x193x203 cm / 100”x76”x80” keep these instructions in a safe place for future reference. You must read these instructions carefully before you start to assemble this greenhouse. Please carry out the steps in the order set out in these inst...

  • Page 2

    I mp o rt ant - a - aluminum profiles and parts. - p5xx – polycarbonate panels. - p3xx – plastic parts. - m – metal parts. - 4xx – screws, nuts, disks, etc. Please carefully read all notes, instructions & remarks, before starting the assembly of the greenhouse. Sort the parts and check against the c...

  • Page 3

    C o n t e n t s item qty. Inc./mm a102 44.33”/1126mm 12 a103 62.40”/1585mm 1 a104 62.40”/1585mm 1 a111 44.69”/1135mm 2 a112 44.69”/1135mm 2 a113 44.96”/1142mm 1 a114 44.96”/1142mm 1 a115 44.96”/1142mm 1 a116 44.96”/1142mm 1 a131 96.73”/2457mm 2 a141 97”/2463mm 1 a151 23.07”/586mm 1 a171 59.65”/1515m...

  • Page 4

    C o n t e n t s (2 spare) k i t a c c e s s o r i e s item qty. Inc./mm m244 2 p517 10.63” x24.09” 1 p513 22.64” x24.09” 1 1135x612 mm 270x612 mm 575x612 mm p516 25.79” x24.09” 1 666x612 mm p514 17.32” x24.09” 2 440x612 mm p515 17.32” x24.09” 2 440x612 mm p505 9.45”x23.94” 1 240x608 mm p512 23.62” x...

  • Page 5

    Be sure to bend in the tabs of the base profiles m243 into a 90° angle before inserting the screws. Tighten firmly the screws 447 at the lower hole as seen in the lower picture. Attach the sides of the base (m244) to the front and back base pieces (m243). Use the aluminum screws and nuts (411, 412) ...

  • Page 6

    Pay attention to set the aluminum corners (a111, a112) according to the marks showing bottom and top. Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose. Note: the assembly of profile a161 should be done simulataneously with profile a111. The other side of profile a161 w...

  • Page 7

    4 insert the screws from the outside, tighten nuts only 2-3 turns and leave loose. Back (a) a112 a111 a112 a111 411 a111 411 412 qty 2 #a111 #a112 a111 2 from the inside.

  • Page 8

    Note: screws 411 should be inserted through the lower of two holes in profile a253. Note: profiles a256 are assembled from the inside. The upper holes will be used later on. Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose. 5 back ! ! A256 a256 411 412 a256 412 411 bac...

  • Page 9

    Note: the set includes two left and two right “gutter end cups” p324 and four plugs. Assemble a plug in all four “gutter end cups” p324. Insert each one of them into the gutters a131 ends. Note: leave the end cup open on the side you would like the water to drain. (a) a131 (b) (b) p324 p324 p324 4 #...

  • Page 10

    Assemble the gutter a131 to the profiles (a111/a112) one on each end. Note: assemble the crossbars a256 from the inside simultaneously with the gutter a131 using the same screws and nuts. The oval holes in a256 must be connected to the base of the greenhouse. Insert the screws from the outside, tigh...

  • Page 11

    A a253 back a104 a103 411 a103 a104 ! Back 412 411 a104 b b ! ! A a 411 a103 a253 the slanted end of the profiles a103 and a104 should be parallel to the downward slope of the roof. The other end should be insert onto the head of screws 411 connecting the crossbars to the base. Insert one screw 411 ...

  • Page 12

    Profiles a254 should be connected through the lower of the two holes to profiles a111 and a112. At their other end, they should be connected to profiles a201 and a202. Note: assemble the crossbars a256 simultaneously with the profiles a254 and profiles a111 and a112, using the same screws and nuts. ...

  • Page 13

    Aluminum profiles a113, a114 are to be connected at the front to aluminum profiles a254 using the upper of the two holes. Aluminum profiles a115, a116 are to be connected at the back to aluminum profile a253 - on its two sides using the upper holes. Profiles a113, a114, a115, a116 are to be also con...

  • Page 14

    Assemble the main beam a141 under a113, a114 at the fr ont, a115 and a116 at the back . A141 411 412 411 412 a211 411 412 412 411 qty 1 #a141 qty 1 #a211 11 insert the screws from the outside, tighten nuts only 2-3 turns and leave loose. Assemble profile a211, from the outside, to profiles a113, a11...

  • Page 15

    Slide profile a102 on to the preassembled (to the base) screw 411. On the other end slide the head of screw 411 into the groove on profiles a102, insert the screw into predrilled holes in the gutter a131 and close (do not tighten) with nut 412. Note: repeat the above assembly procedure to all six pr...

  • Page 16

    Slide profile a102 on to the preassembled (to the base) screw 411. On the other end slide the head of screw 411 into the groove on profiles a102, insert the screw into predrilled holes in the gutter a131 and close (do not tighten) with nut 412. 412 411 a102 a102 (a) (b) 412 411 insert the screws fro...

  • Page 17

    Note: the vent in the roof can be inserted replacing one of the middle sections panels. In order to assemble the vent you have to insert an additional screw 411(b) into two profile a102(b) on both sides of the vent before you connect it. These two additional screws will be used in the next step. 411...

  • Page 18

    Assemble aluminum profile a251 using the additional screws you inserted on the previous step. 412 a251 a251 a251 412 a261 a221 (a) (b) a211 412 411 442 412 441 (b a261 412 441 a261 442 441 (c) assemble aluminum profile a221 onto aluminum profile a211(a) . Connect aluminum profile a221(b) and aluminu...

  • Page 19

    P301 a191 a191 p301 p301 a191 p301 lay profiles a171 l&r on a flat surface. Lay between them profiles a172, a181 and a191 including preassembled p301 as shown below and tighten all screws. Door assembly- when inserting the plastic part no. P301 to aluminum profile a191 use plastic or rubber mallet. ...

  • Page 20

    When inserting the panel to the door use a flat surface and if the panel does not fit properly, trim the lower and upper corners of the panel. Note : make sure the grooves on both sides of the panel are properly positioned along the aluminum-extruded profiles. C d b d c b a a 19 20 qty 1 #p502 durin...

  • Page 21

    Qty 2 #p313 21 a231 411 412 a181 412 411 412 a231 a181 lay profile a231 on profile a181 and connect them with screws and nuts 411 , 412 . 22 a231.

  • Page 22

    443 421 p302 422 443 422 a231 p302 422 a181 p302 443 a231 421 443 qty 421 #p302 2 2 qty 443 422 4 2 23 assemble of the wheels to profile a231 . Note : make sure to assemble all parts in the order described in illustration below. Part no’ 443 must be assembled, one under screw 421 head and one betwee...

  • Page 23

    Vent subassembly assemble the handle a306 to profile a271 and tighten screws 421(a) and nuts 422(a). Slide panel p512 into the groove in profile a151(b). Slide profiles a282 on each side of panel p512 until they fit the holes on profile a151 ends and the two holes on panel p512(c). 422 a306 421 a271...

  • Page 24

    (b) a251 a141 a306 (b) (a) inside a251 445 a251 a323 the brackets a323 should be connected to profile a251 using screws 445(a). To install the vent on main bean aluminum profiles a141, hold it at an angle of 45° relative to the profile’s plane slide it to the position between the two roof aluminum p...

  • Page 25

    Qty 14 #p317 28 p317 p317 p317 noise reduction elements assembly. Put one part of p317 in the middle of each section of the wall as shown in the picture below it will be used later on..

  • Page 26

    (b3) (b1) (b2) note: make sure the panel is secure in p317 plastic holder (a). Make sure the grooves on both sides of the panel are properly positioned along the aluminum – extruded profiles. * see also next step. During the assembly of the plastic strips you must put pressure on them until they sna...

  • Page 27

    Pay special attention when assembling the triangular polycarbonate sections (p505, p514 and p515). The plastic strips (p311,p312,p314,p315) should be installed only after the polycarbonate panels (p505, p514, and p515, p516) are in position. * (see previous step) p502 p502 p502 p502 p502 p502 p502 p...

  • Page 28

    When you mount the polycarbonate panels on the roof, insert the panels by sliding them into the gutter as shown in the picture below. Noise reduction elements assembly. Insert one part p316 in the middel of each of the roof panels and push it in the groove of the gutter. * a step ladder will be need...

  • Page 29

    307 when fitting the door in its place, pay attention to insert the plastic part (p301) inside the special aluminum rail (a161(a)). It is advised to spread some tender lubrication on the rail. After you assemble the door to its place, assemble screw and nut 411,412 into the door stopper hole on prof...

  • Page 30

    Firmly connect the greenhouse to leveled final position immediately after completion of the assembly, to withstand high winds effects. The pegs m307 (spikes) are assembled from the inside of the greenhouse. Make sure to use the pre-punched notch in the bottom of the base. M307 34.