1. DL manuals
  2. Palsonic
  3. CRT TV
  4. 3400
  5. Owner's Manual

Palsonic 3400 Owner's Manual

Manual is about: 34CM CORDLESS REMOTE COLOUR TELEVISION

Summary of 3400

  • Page 1

    Palsonic corporation pty ltd 1 joynton avenue waterloo nsw 2017 australia tel:(02)9313 7111 fax:(02)9313 7555 www.Palsonic.Com.Au palsonic customer service telephone australia:1300 657 888 34cm cordless remote colour television model: 3400 owner's manual type tested electrical safety as/nzs 3250 lic...

  • Page 2: Contents

    Congratulations on your purchase of this palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents notes ...

  • Page 3

    . This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and ...

  • Page 4

    Av in/out 1. Antenna connections 1.1 optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. 1.2 insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position of the outdoor antenna for the be...

  • Page 5: Llllllllll.....

    3.1 standby ( ) button 3.1.1 press standby ( ) button to turn on the set (the indicator shows yellow) when the set is in standby mode (the indicator shows red) , the channel position number is displayed in the screen. Press standby ( ) button to return the set to the standby mode when the set is in ...

  • Page 6: Llllllllllllll

    3.2.2.4 press preset on/off button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 repeat 1~ 4 steps to search another channel. Note : * if the same channel position is selected during repeat operation, the former memory will be erased. *...

  • Page 7: .........................

    3.5 volume control 3.5.1. Press the vol button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the vol button to decrease volume ; the green bar on the screen moves left. 8 display of minimum volume display of maximum volume ......................... 3.6 av/tv selector pre...

  • Page 8

    4. Remote control operation: remote control unit : standby 1 ~ 9 : digital channel selector 10/0 : channel 10 or channel 0 selector system : colour system control -/- - : digit or two digit channel select : previous 4.1 installing batteries: 4.1.1 remove the battery cover of remote control unit. 4.1...

  • Page 9

    4.3 channel selection 4.3.1 press channel selector ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen. 4.3.2 use the digital channel selector button for direct channel selection. 1) 1~10 channel method 1: example: to select channel 2 to select...

  • Page 10: Llllllllll.....

    6 5 4.3.3 previous button pressing this button to select the channel that was tuned immediately before the one being watched. For example: if you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach chann...

  • Page 11

    4.6 making use of pps button (personal preference select) press the pps button, the screen will display the following five mode progressively: press pps again press pps again the above five display modes corresponding analogue quantity is shown in the following chart: brightness 4.7 display button (...

  • Page 12

    4.8 sleep button 4. 8. 1 using sleep button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to stand by mode. 4. 8. 2 after the sleep function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. Note...

  • Page 13

    4.9.1 clock 4.9.1.1 press the timer button till "clock" displays-on the screen. 4.9.1.2 press the button to set the present hour. Press the button to set the present minute. 4.9.1.3 after setting the clock, press time set button to start operating. Now the indication on the screen is green instead o...

  • Page 14

    Auto 4.9.8.8 press time set button, then the off time indication is green instead of red. Off time function starts operating. 4.9.8.4 the appliance will be turned off when your setting time is up, and return to stand by mode. Note: * the built-in clock employs the 24-hour system. * the off time func...

  • Page 15

    5. 2. 2 press av/tv button of the tv set or on the remote control unit to set the set to tv mode, and choose the desired channel. Note: the following mis-operation should be avoided during recording. * press standby button or set to video mode. * change the current channel accidentally. 5.1.2 press ...

  • Page 16

    5. 3. 2 press av/tv button of the tv set or on the remote control unit to select video mode before dubbing, "video" will be displayed on the screen. The tv set will act as a monitor to help you edit while dubbing. Note: the set must remain in video mode and must not be switched off during the sessio...

  • Page 17

    6. Trouble shooting guide symptoms check these things try these adjustment no picture, no sound. Be sure power cord is plugged in. May be station trouble. Check antenna connections. Maybe in av mode. Press power button try another channel. Press av button once. Poor sound, picture ok. May be station...

  • Page 18

    7. Specifications: tv system: receiver channel power supply crt antenna impedance dimension (mm) weight power consumption remote control unit power supply * design and specifications are subject to change without notice. : pal, b/g; ntsc 3.58/4.43 playback : vhfl 0-5, 5a; vhfh 6-11; uhf 21-69 : ac 2...

  • Page 19

    Palsonic corporation pty ltd 1 joynton avenue waterloo nsw 2017 australia tel:(02)9313 7111 fax:(02)9313 7555 www.Palsonic.Com.Au palsonic customer service telephone australia: 1300 657 888 604-37703-03.