Summary of PNG125
Page 1
User’s manual png125 bluetooth speakerphone 040712r2.
Page 2: Contents:
Contents: 1 - specification. 2 - getting to know your png125. 3 - overview. 4 - recommended installation position. 5 - using the car charger. 6 - turning on and off your png125 7 - pairing your png125 8 - connection/link between png125 and mobile phone. 9 - using the png125. 10 - multipoint feature....
Page 3: Specification
1 specification bluetooth specification v2.1 +edr bluetooth profiles supported headset, handsfree transmission power class2 frequency range up to 10 metres battery li-ion polymer built-in rechargeable 3.7v / 340mah 1.26wh charging voltage dc4.75-5.25v pairs up to 8 devices multipoint yes charging ti...
Page 4: Contents:
2 getting to know your png125. To use your bluetooth png125, please follow these simple steps. 1) charge prior to using the png125, it is recommended you charge the battery fully for the first time. Normal full charge time is 2 hrs (approx). 2) place your png125 and a bluetooth-enabled device within...
Page 5
3 overview. 1) speaker. 2) microphone. 3) status indicator led. 4) charging socket (micro 5-pin usb). 5) mfb button (multifunction button). 6) volume increase (v+). 7) volume decrease (v-)..
Page 6
4. Recommended installation position. It is recommended that the png125 is positioned on to the top of the sun visor as shown in the picture below. Do not obscure your vision. Warning: do not place or store the png125 over the area of the car safety airbag deployment or it may cause serious injury i...
Page 7: Turning The Png125 On/off
5 using the charger. When the engine is running insert the car charger plug fully in to the cigarette socket until the led flashes red. Normal full charge time is 2 hours (approx), and the led will turn off when fully charged. Remove charger after use and only reconnect when engine is running. Warni...
Page 8: Pairing
7 pairing prior to using the png125 for the first time, you must pair it with a bluetooth-enabled device. The steps below describe the pairing procedure for a typical bluetooth-enabled mobile phone. 1) place the png125 and mobile phone no more than 1 metre apart. 2) ensure the png125 is in the off m...
Page 9: Reconnecting
Png125 will return to standby mode if no device is paired or connected within 2 minutes of activating pairing mode on the png125. 8 reconnecting when png125 is disconnected due to being out of range or switched off, just click the mfb once and it will be reconnected to the paired device (some models...
Page 10: Using The Png125
9 using the png125 1) answering a call when receiving a phone call, press the “mfb” button once to answer the call. 2) ending a call press the “mfb” button once during a call. 3) reject a call when you hear the ringing tone, press and hold the “mfb” button for 3 seconds to reject the call. 4) voice ...
Page 11: Transferring Calls
7) transferring calls a. During a call press both “v+” and “v-” buttons simultaneously you will hear a beep and the call will be routed to your mobile phone. B. Repeat the same procedure to refuse a call back through png125. 8) mute a. During a call press "v-" button for 3 seconds you will then hear...
Page 12
A. Start with your png125 turned off, press and hold mfb for 5 seconds until blue and red lights flash alternately. B. On your mobile phone activate bluetooth and search for devices when png125 is disconnected select png125 and enter pairing code '0000' c. Now connect to png125. D. Switch of png125 ...
Page 13
2) multipoint connection/link with two mobile phones after the multipoint function is activated, please follow the steps below to connect with two bluetooth enabled mobile phones at the same time. When the power is on the png125, will automatically search and connect the last two mobile phones that ...
Page 14: Restore To Default Setting
Notes: when the multipoint feature is being used, the device cannot support 3 way calling feature. 11 low voltage protection of battery when the voltage of the battery has decreased to 3.3v, the red led light will flash every three seconds, and the png125 will power off automatically when the voltag...
Page 15: Led Light Indicators
Note: if the png125 is connected with a mobile phone before restoring the default settings, it will enter pairing mode automatically after it is restored to default. If the png125 is not connected with the mobile phone before restoring the default settings, it will be in standby mode after restoring...
Page 16: Warranty
Eu this product is ce certified according to the provision of the r&tte directive (99/5/ec). This product is in compliance with the essential requirements and other relevant provisions of directive 1999/5/ec. Please note that this product uses radio frequency bands not harmonized within eu. Within t...
Page 17: Helpline:
* the warranty is not applicable if the product has been subject to abuse, improper installation, modification or repair by unauthorised third party. * the responsibility of the supplier’s products shall be limited to the repair or replacement of the product at its sole discretion. * specifically ex...
Page 18: Www.Pama.Com
Manufactured to the highest possible standards, combining style with functionality to bring you the ultimate handsfree product. Www.Pama.Com made in china..