1. DL manuals
  2. Panamax
  3. Surge Protector
  4. M4320-PRO
  5. Instructions Manual

Panamax M4320-PRO Instructions Manual

Other manuals for M4320-PRO: Quick Start Manual, Specifications
Manual is about: Power Management with Control System Interactive Functionality.

Summary of M4320-PRO

  • Page 1

    1 2 3 4 5 6 7 8 unsafe voltage breaker wiring fault temperature 20 a brightness outlet status reboot 1 reboot 2 m4320-pro b lt blue ™ enabled volts power management with control system interactive functionality. • 20 amp capacity m4320-pro • 8 individually controllable rear panel outlets • fully pro...

  • Page 2: Introduction

    Thank you for purchasing a panamax m4320-pro power management with control system interactive functionality, and congratulations on your choice. The m4320-pro features panamax’s revolutionary avm (automatic voltage monitoring) circuit, and our exclusive linear filtering technology (lift). To- gether...

  • Page 3: Features Descriptions

    Features descriptions 1 bluebolt ™: remote power management technology provides secure, hosted ip (internet protocol) system control. With bluebolt™, custom electronics installers, integrators and end-users can remotely monitor and control power to home theater equipment by accessing power managemen...

  • Page 4

    2 1 2 3 4 5 6 7 8 unsafe voltage breaker wiring fault temperature 20 a brightness outlet status reboot 1 reboot 2 m4320-pro b lt blue ™ enabled volts always on 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Warning: do not use this appara...

  • Page 5: Preset Profile Information

    Preset profile information 3 default outlet sequencing (preset profile p1, by outlet #s): start up: 1→(1 sec)→2→(1 sec)→3→(1 sec)→4→(1 sec)→5→(1 sec)→6→(1 sec)→7→(5 sec)→8 shut down: 8→(5 sec)→7→(5 sec)→6→(1 sec)→5→(1 sec)→4→(1 sec)→3→(1 sec)→2→(1 sec)→1 reboot 1: 1(off)→(30 sec)→1(on) reboot 2: 2(o...

  • Page 6: The Bubble of Protection

    The bubble of protection ground outlet 8 outlet 7 outlet 6 outlet 5 outlet 4 outlet 3 outlet 2 outlet 1 filter bank 4 filter bank 3 filter bank 2 filter bank 1 catv / sat 1 catv / sat 2 lan cat 5e telco dc trigger ac inlet bluebolt-cv1 in o u t ground outlet 8 outlet 7 outlet 6 outlet 5 outlet 4 out...

  • Page 7: Getting Setup For Bluebolt

    5 getting setup for bluebolt ™ bluebolt online registration note: make sure to complete system setup #1 or # 2 before registering. Step 1. Log into http://www.Mybluebolt.Com for online registration. Your bluebolt™ enabled m4320-pro power management component is completely plug-and-play and does not ...

  • Page 8: Identify Connected Equipment

    6 identify connected equipment use this diagram to write in what pieces of equipment are plugged into each outlet for an easy reference. Please note that the outlets start at no. 8 on the left. The outlet indicator lights on the front panel are numbered 1 through 8 left to right. Outlet outlet outle...

  • Page 9

    7 0. Overview the purpose of this document is to outline the command set used to communicate with and control the m4320-pro. The data communication feature will most often be used to interface with automation systems. It may also be used to control and configure the unit manually using a standard te...

  • Page 10

    8 rs-232 and telnet command set / protocol specification (continued) 2.3 comm. System: asynchronous, half-duplex 2.4 baud rate: 9600bps 2.5 start bits: 1 2.6 data bits: 8 2.7 stop bits: 1 2.8 parity: none 2.9 flow control: none 3. Controller commands the following are commands sent by the controllin...

  • Page 11

    9 rs-232 and telnet command set / protocol specification (continued) 3.10.2 action: sets the linfeed mode to mode. 3.10.3 response: if mode = on, $linefeed = on if mode = off, $linefeed = off if mode is invalid, $invalid_parameter 3.11 reset factory settings resets all of the custom configuration se...

  • Page 12

    10 reboot1 delay = 30 reboot2 delay = 30 feedback = on linefeed = on profile = 2 3.12.4 action: p3 configuration below: trigger for 1 = button_1, green_button trigger for 2 = green_button trigger for 3 = button_2, green_button trigger for 4 = green_button trigger for 5 = dc_trigger , green_button tr...

  • Page 13

    11 rs-232 and telnet command set / protocol specification 5. Responses and warning messages if unsolicited feedback is enabled, the following warning messages will be transmitted under the conditions outlined in their description. 5.1 outlet status change 5.1.1 condition: outlet or trigger output ch...

  • Page 14: Fcc Notice

    Fcc notice this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful in- terference in residential installation. This equipment generates, uses, and...