Aj- p operation instructions s.S base station.
- 1 - safety precautions caution risk of electric shock do not open caution: to reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer to servicing to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral tria...
- 2 - safety precautions ..................................................................... 1 features .................................................................................... 2 checkpoints for system connections ......................................... 2 parts and their functions......
- 3 - parts and their functions front panel cable short alarm fuse head power on off main on off fuse open digital triax 1 2 4 5 6 3 7 8 400v 1a 250v t 2.5a l 5 power fuse (fuse) this is the main power supply fuse of the aj-bs900p. Use a dedicated dc fuse (400v 1a) which can withstand inrush. 6 came...
- 4 - = mic button this button is used to switch the intercom microphone on and off. It has three positions: on, off, and ptt. (ptt: audio transmission continues as long as the button is held down.) intercom level knob this knob is used to adjust the volume of the microphone input to the intercom. P...
- 5 - parts and their functions m awb button this is the auto white balance button. It does not work when the l white bal switch is set to the prst position. Button led lit: auto white balance in progress. Button led dark: auto white balance completed. Button led stops blinking and goes off: auto wh...
- 6 - parts and their functions front panel a moni sel switch this switch is used to switch the signals output from the pix and wfm jacks on the rear panel of the aj-bs900p. _ knee point knob this knob is used to set the manual knee point. ` detail knob this knob allows adjustment of the master deta...
- 7 - parts and their functions ext dc in gen– lock enc 1 enc 2 enc 3 pix y/g 4:2:2 4:2:2 sdi out out in op4 op3 wfm tally fuse 400v 15a signal gnd ac in audio out ch 1 push ch 2 push communication pb/b pr/r wfm ret 1 ret 2 prompt 1 2 3 4 5 7 6 8 9 : ; = > ? @ a b c d e enc 1 enc 2 enc 3 pix y/g 4:2...
- 8 - parts and their functions rear panel ? Tally connector this is the connector for the r tally and g tally signals. It can be used for pm tally. @ dc power fuse (fuse) this fuse is for the aj-bs900p’s dc power supply. Use a dedicated dc fuse (400v 15a) which can withstand inrush. A 4 : 2 : 2 con...
- 9 - pix output menu indications pix output setting menu indications when the set up button is pressed so that it lights, setting menu indications are output via the pix output connector. The setting menus consist of main menus and submenus. Setting menus are displays one page at a time. All of the...
- 10 - main menu 1/2 screen the items on this menu cannot be set using the set up dial. They are set using the controls on the front panel. 1 syncro scan screen this screen is used to make synchro scan settings. # synchro scan : 1/60.8 2 vr data screen this screen displays the setting values for the...
- 11 - main menu 1/2 screen # r flare : 000 g flare : 000 b flare : 000 r gamma : +00 b gamma : +00 8 flare/gamma screen this screen is used to select the camera’s flare and gamma settings. 7 knee/level screen this screen is used to select the camera’s setup level settings. # manual knee : on white ...
- 12 - main menu 2/2 screen = diagnostic screen this screen is displays the software version. # version : ver ¢ . ¢ . ¢ > up date : ¢¢¢¢ . ¢¢ . ¢¢ # detail : on 2d lpf : off super color : on gamma : on test saw : off flare : on h-f compe. : on negative dtl : off ; camera setting screen this screen i...
- 13 - shading adjustment when the black or white (v.Saw) setting on the auto shading menu or the white (digital) setting on the white shading menu is selected to perform shading, menus similar to those shown below appear. The operation procedure is illustrated below using black shading as an exampl...
- 14 - connectors and signals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 communication 1 prod to l (h)* 2 prod to l (c)* 3 prod from l (h)* 4 prod from l (c)* 5 shield* 6 eng to l (h) 7 eng to l (c) 8 eng from l (h) 9 eng from l (c) 10 shield 11 r tally in (h) 12 r tally in (c) 1...
- 15 - connectors and signals a b c d e f g h wfm a stair out b stair en c rem sync d e gnd f 1lin / 1fld g rem sync en h tally a r tally (h) b r tally (c) c g tally (h) d g tally (c) e gnd f r tally out g g tally out h +12v j gnd k l m manufacturer part number: prc07-r8f (tajimi musen) manufacturer...
- 16 - switches cable short alarm fuse head power on off main on off fuse open digital triax genlock off sc h coarse intercom pgm on off ptt mic private system push phase vtr enable rew ff stop shutter set up mon sel knee point knee slope gamma detail m.Ped on off (push) r g eng seq b sup s.V s.S 10...
- 17 - switches 2 1 3 4 5 6 7 power make g tally selector switch (sw6) refer to the diagram at right and select the desired switch position. 4 -20db 0db mic1 selector switch (sw7) refer to the diagram at right and select the desired switch position. 5 -20db 0db mic2 selector switch (sw8) refer to th...
- 18 - switches sw2 on off 8 7 6 5 4 3 2 1 bs digital board sw2-1: y/g, pb/b, pr/r selector switch on: y, pb, pr output off:g, b, r output sw2-6: color bar setting selector switch on: sng color bar off:smpte/full color bar when selecting the positions of the above switches, make sure that you do not...
- 19 - specifications input: 120 v ac, 50/60 hz, 180 w (ext in dc 11.0 - 17.0v, 12a) output: 100 v dc, 850 ma external dimensions (w x h x d): 8-5/16" x 5-15/16" x 17-15/16" (211x 151 x 455.5 (mm) ) weight: 19.8bs (9.0 kg) operating temperature range: 32 f – 72 f (0 °c – 40 °c) storage temperature r...
- 20 - specifications intercom microphone selection: switchable between dynamic microphone and carbon microphone i/o level: 4-line/2-line: 0 dbm (600 Ω , balanced) rts: 1 v p-p (200 Ω ) pgm: 0 db (600 Ω , balanced) format: selectable between 4-line, 2-line, and rts lines: base station to camera: 2 l...
Panasonic broadcast & digital systems company division of matsushita electric corporation of america executive office: 3330 cahuenga blvd w., los angeles, ca 90068 (323) 436-3500 eastern zone: one panasonic way 4e-7, secaucus, nj 07094 (201) 348-7621 mid-atlantic/new england: one panasonic way 4e-7,...
Aj- p manual d’utilisation s.S station de base f1100t printed in japan vqt8994 p.
1 nous vous remercions d’avoir choisi cette station de base aj-bs900p (qui sera simplement appelée “l’appareil” dans la suite de ce mode d’emploi). L’appareil se raccorde à un camescope dvcpro ou dvcpro50 pour configurer un système de transmission utilisant un câble triaxial pour permettre au camesc...
2 consignes de sécurité ............................................................... 1 caractéristiques......................................................................... 2 points à vérifier pour les raccordements système ..................... 2 les commandes et leurs fonctions ...............
3 les commandes et leurs fonctions panneau avant cable short alarm fuse head power on off main on off fuse open digital triax 1 2 4 5 6 3 7 8 400v 1a 250v t 2.5a l 5 fusible d’alimentation (fuse) utiliser un fusible cc (400 v, 1 a) réservé capable de supporter des courants transitoires. 6 fusible d’...
4 = touche de microphone (mic) cette touche permet de mettre le microphone en et hors service. Il possède trois positions : on, off, et ptt. (ptt : la transmission audio se poursuit tout le temps que la touche est maintenue enfoncée.) bouton de niveau d’intercom (intercom) ce bouton permet de régler...
5 les commandes et leurs fonctions m touche awb c’est la touche de réglage automatique de la balance des blancs. Elle ne fonctionne pas si le commutateur white bal l est réglé sur la position prst. Led de la touche allumée: réglage automatique de la balance des blancs en cours. Led de la touche étei...
6 les commandes et leurs fonctions panneau avant o commutateur de mire (bar) ce commutateur permet d’envoyer un signal de mire depuis l’aj-bs900p. La tête de la caméra ne commute pas au mode de mire. A commutateur moni sel ce commutateur permet de commuter les signaux envoyés par les prises pix et w...
7 les commandes et leurs fonctions ext dc in gen– lock enc 1 enc 2 enc 3 pix y/g 4:2:2 4:2:2 sdi out out in op4 op3 wfm tally fuse 400v 15a signal gnd ac in audio out ch 1 push ch 2 push communication pb/b pr/r wfm ret 1 ret 2 prompt 1 2 3 4 5 7 6 8 9 : ; = > ? @ a b c d e enc 1 enc 2 enc 3 pix y/g ...
8 les commandes et leurs fonctions panneau arrière ? Connecteur de signalisation (tally) c’est le connecteur des signaux de signalisation r et des signaux de signalisation g. Il peut également servir à la signalisation pm. @ fusible d’alimentation cc (fuse) ce fusible est celui de l’alimentation cc ...
9 indications du menu de sortie pix indications du menu de sortie pix lorsqu’on appuie sur la touche set up de façon qu’elle s’allume, les indications des menus d’initialisation sont envoyées via le connecteur de sortie pix. Il y a deux sortes de menus de réglage, les menus principaux et les menus a...
10 ecrans de main menu 1/2 il n’est pas possible de régler les rubriques de ce menu avec la molette set up. Elles se règlent avec les commandes du panneau avant. 1 ecran synchro scan cet écran permet de régler la synchronisation de balayage. # synchro scan : 1/60.8 2 ecran vr data cet écran permet d...
11 ecrans de main menu 1/2 # r flare : 000 g flare : 000 b flare : 000 r gamma : +00 b gamma : +00 8 ecran flare/gamma cet écran permet de sélectionner les paramètres de gamma et de lumière parasite de la caméra. 7 ecran knee/level cet écran permet de sélectionner les paramètres de niveau d’initiali...
12 ecrans de main menu 2/2 = ecran diagnostic cet écran affiche la version du logiciel. # version : ver ¢ . ¢ . ¢ > up date : ¢¢¢¢ . ¢¢ . ¢¢ # detail : on 2d lpf : off super color : on gamma : on test saw : off flare : on h-f compe. : on negative dtl : off ; ecran camera setting cet écran permet de ...
13 réglage de l’ombrage lorsqu’on sélectionne la rubrique black ou white (v.Saw) dans le menu auto shading ou la rubrique white (digital) dans le menu white shading pour effectuer un ombrage, des menus semblables à ceux indiqués ci-dessous s’affichent. Nous expliquons la procédure avec un exemple de...
14 brochage des connecteurs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 communication 1 prod vers l (h)* 2 prod vers l (c)* 3 prod depuis l (h)* 4 prod depuis l (c)* 5 blindage* 6 eng vers l (h) 7 eng vers l (c) 8 eng depuis l (h) 9 eng depuis l (c) 10 blindage 11 entrée de signal...
15 brochage des connecteurs a b c d e f g h wfm a sortie stair b stair en c synchro rem d e terre f 1 ligne/1 trame g synchro rem en h tally a signalisation r (h) b signalisation r (c) c signalisation g (h) d signalisation g (c) e terre f sortie de signalisation r g sortie de signalisation g h +12v ...
16 les commutateurs cable short alarm fuse head power on off main on off fuse open digital triax genlock off sc h coarse intercom pgm on off ptt mic private system push phase vtr enable rew ff stop shutter set up mon sel knee point knee slope gamma detail m.Ped on off (push) r g eng seq b sup s.V s....
17 les commutateurs 2 1 3 4 5 6 7 power make commutateur de sélection de signalisation g (sw6) sélectionner la position du commutateur en se reportant au schéma de droite. 4 -20db 0db commutateur de sélection mic 1 (sw7) sélectionner la position du commutateur en se reportant au schéma de droite. 5 ...
18 les commutateurs sw2 on off 8 7 6 5 4 3 2 1 carte bs digital sw2-1: commutateur de sélection y/g, pb/b, pr/r on: sortie y, pb, pr off:sortie g, b, r sw2-6: commutateur de sélection de réglage de la mire de couleur on: mire de couleur sng off:mire de couleur smpte/full lors du réglage des commutat...
19 fiche technique entrée: 120 v ca, 50/60 hz, 180 w (ext in dc 11.0 - 17.0v, 12a) sortie: 100 v cc, 850 ma dimensions externes (l x h x p) : 211 x 151 x 455,5 (mm) poids: 9,0 kg plage de température de fonctionnement: 0 °c - 40 °c plage de température de rangement: -10 °c - +50 °c humidité de fonct...
20 fiche technique intercom sélection du microphone: sélection microphone dynamique/microphone au carbone niveau d’e/s: 4 lignes/2 lignes : 0 dbm (600 Ω , symétrique) rts: 1 vcac (200 Ω ) pgm: 0 db (600 Ω , symétrique) format: sélection entre 4 lignes, 2 lignes et rts lines: station de base vers cam...
Panasonic canada inc. 5770 ambler drive, mississauga, ontario l4w 2t3 (905) 624-5010