Panasonic AJ-HPX3100G Manual - page 9
Control Unit, which enables full control over image adjustments and
recording, teams with the lightweight, compact, and highly mobile
AG-CA300G Camera Adaptor.
*Power can be supplied only when the AG-BS300 Base Station is driven by an AC power
source. A separate power cord is also required between the AG-BS300 Base Station and the
AG-CA300G Camera Adaptor.
Remote Control-Ready
The AG-EC4G Extension Remote Control Unit or AJ-RC10G Remote
Control Unit* offer both studio use and direct connection to the
AJ-HPX3100G. This lets you adjust the images and control the
camera operation while viewing the monitor.
*The remote control unit can control only functions supported by the
AJ-HPX3100G. It cannot control unsupported keys or dials.
HD/SD SDI Output Terminals and Down-Converter
Two video line output terminals (BNC) are provided as standard
equipment and flexibly support monitoring and line recording. The
built-in down-converter outputs high-quality SD video signals for
broadcasting use. The aspect mode can also be selected.
•SDI OUT (HD/SD): Can also output signals with embedded audio.
Backup recording operation can be interlinked with the Rec Start/
Stop controls of an HD-SDI input-equipped Panasonic recorder, such
as the AG-HPG20, etc. The AJ-HPX3100G can also output down-
converted SD-SDI from an HD source.
•MON OUT: Can output HD SDI/SD SDI/Composite. HD signals can
be down converted.
Standard HD/SD SDI Input Terminals
The AJ-HPX3100G supports line recording through the SDI input
terminal; thus, it can be used as a portable recorder. It supports
1080/59.94i, 1080/50i, 480/59.94i and 576/50i input signals.
*The input signal must be in the same format as the recording format of the camera recorder.
Genlock Terminal for Return Video Signal Input
Return video signal (analog HD-Y signal) input to the GENLOCK IN
terminal or HD/SD video signal (HD/SD SDI signal) input to the SDI IN
terminal can be viewed on the viewfinder.
*The input signal must be in the same format as the recording format of the camera recorder.
XLR Audio Input with Automatic Switching Function
The 2-channel XLR audio input terminals on the rear panel are
compatible with a +48 V phantom power supply. The new automatic
front/rear switching function automatically selects the rear input
signal when input is connected to the rear terminal.
USB 2.0 Interface
The AJ-HPX3100G incorporates the Host and Device USB 2.0 as
standard connectors. In Device mode, a P2 card slot can be used as
an external PC device. In Host mode, an external hard disk drive can
be connected, making it easy to copy data from the P2 card to HDD.
The thumbnails of stored video in HDD also can be viewed.
TC IN, TC OUT Terminals
The AJ-HPX3100G has a built-in SMPTE time code generator/reader.
TC IN and OUT terminals make time code throughput possible. This
permits an external time-code lock.
Other System Functions and Options
• UniSlot
®
wireless receiver compatible (2 channels).
* UniSlot® is a trademark of Ikegami Tsusinki Co., Ltd.
• Anton/Bauer light connector on the top (lower front side of the
handle).
• Equipped with earphone terminals (stereo mini-jack) and speaker.
• Multiple battery support, including Anton/Bauer or IDX batteries*.
* The V-mount battery plate is required for IDX batteries.
Compatibility with Nonlinear Editing Systems
There are many nonlinear editing products in the market that already
support P2. P2 native editing makes it possible for you to maintain
high-quality video and a flexible editing workflow.*
* For information on compatible nonlinear editing systems, visit panasonic.co.jp/pro-av/> and click “Nonlinear Compatibility Information.” For the operating requirements and other details of editing software, visit the website of the relevant software manufacturer. Recording Mode File Format Video Audio Total Record Rate* 3 Recording Time* 3 (per 1GB) Resolution Codec Bit Rate channel Codec SHQ 2CH MOV* 1 MOV 960×540 H.264 High Profile 3500 kbps 2CH Linear PCM Approx. 5060 kbps Approx.25 min. HQ 4CH MOV* 1 MOV 640×360 H.264 High Profile 1500 kbps 4CH AAC-LC Approx. 1780 kbps Approx.72 min. HQ 2CH MOV* 1 MOV 640×360 H.264 High Profile 1500 kbps 2CH AAC-LC Approx. 1650 kbps Approx.78 min. LOW 2CH MOV MOV (1080) 480×270 (NTSC) 352×240* 2 (PAL) 352×288* 2 H.264 Baseline Profile 800 kbps 2CH AAC-LC Approx. 950 kbps Approx.135 min. STD 2CH MP4 (default) MP4 320×240 MPEG-4 Simple Profile 1500 kbps 2CH AAC-LC Approx. 1650 kbps Approx. 78 min. *1: These modes can not be selected when the P2 card recording mode is set to SD. *2: Only this mode can be selected when the P2 card recording mode is set to SD (NTSC/PAL). *3: Total recording rates and recording times are reference values which were obtained from continuous recording using our products. Actual recording time varies depending on the recorded scenes and the number of clips. List of proxy data supported by the AJ-YDX30G video encoder board AJ-HPX3100G SDI (HD/SD) Analog Composite AG-HPD24 Memory Card Portable Recorder SDI OUT VIDEO OUT Monitor USB 2.0 (HOST) USB 2.0 (DEVICE) Upload File Copy HDD NLE AJ-HPX3100G Monitor VBS AJ-RC10G Remote Control Unit or AG-EC4G Extension Control Unit Camera Image Remote Control 10P Cable (10 m (33feet) / 50 m (164 feet)) AJ-HPX3100G SDI Bound Cable made by Canare Electric G/L HD/SD SDI HD/SD SDI BT-LH2550 LCD Video Monitor Headset (produced by another manufacturer) Headset (produced by another manufacturer) max. 100 m / 328 feet G/L, Return Video, Tally Power supply Bound Cable made by Canare Electric V2PCS25-5CFWCE-SF-SC (25 m / 82 feet) V2PCS50-5CFWCE-SF-SC (50 m / 164 feet) V2PCS100-5CFWCE-SF-SC (100 m / 328 feet) AG-CA300G Camera Adaptor AJ-RC10G Remote Control Unit or AG-EC4G Extension Control Unit G/L Return Video/Tally AG-BS300 Base Station AJ-HPX3100G AG-YA500G VF interface Box Return Video, Tally Remote Cable (bundled to AG-CA300G) 8