Panasonic BL-PA300KTA - High Definition Power Line Communication Ethernet Adaptor Twin Getting Started Manual
PNQX1294ZA
KK0508MJ0
Getting Started
PLC Adaptor Starter Pack
Power Line Communication
Set of 2 Adaptors (Master and Terminal)
Included items
Example of an integrated HD-PLC network
Installation
Placing the adaptors
Connecting adaptors to network devices
For best results
Avoid connecting high power-consuming appliances to the same wall outlet. Additionally,
connecting an adaptor to a uninterruptable power supply (UPS) or backup power supply
device is not recommended.
While connecting the adaptors to a wall outlet is recommended, keep the following in mind
if you must connect an adaptor to a power strip:
- Make sure the power strip does not a have a noise filter or a surge protector, as these
features may interfere with the performance of your adaptors.
- Do not connect the adaptor to a power strip that receives power from another power
strip.
- Use a power strip with an AC cord that is as short as possible.
For more information, refer to the included Operating Instructions.
For Best Performance
■ We recommend plugging the adaptor directly into a wall outlet whenever possible.
■ AC adaptors and battery chargers (such as cell phone chargers) may interfere with
the performance of this product. We recommend connecting such devices to a power
strip which has a noise filter.
■ You can test the speed of each terminal’s network connection. Refer to the included
Operating Instructions for details.
Model No.
BL-PA300KTA
PLC Adaptor × 2
One adaptor is pre-configured as the “master” adaptor,
and the other is pre-configured as the “terminal” adaptor.
LAN Cable × 2
Order No.: PQJA10138Z
Connects each adaptor
to a network device.
Connect the adaptor to a wall outlet in the room where you plan to use it.
Confirm that the PLC indicator of each adaptor lights in green when you plug
the adaptors into the wall outlets.
• If the indicators are not lit as shown below, confirm all connections and refer to the
troubleshooting section of the Operating Instructions.
Connect a LAN cable to each adaptor’s LAN jack.
The LAN indicator of each adaptor turns green.
Connect the other end of each LAN cable to a network device.
• If the indicators are not lit as shown below, confirm all connections and refer to the
troubleshooting section of the Operating Instructions.
PLC
LAN
MAST
ER
HD
-PL
C
BL
-PA
300
SE
TU
P
MASTER TERMINAL
PLC
LAN
MAS
TER
HD
-PL
C
BL
-PA
300
SET
UP
MASTER TERMINAL
INTERNET
Master
PC
Network printer
Wall outlet
Wall outlet
Wall outlet
Hub
Network camera
Modem
Router
PC
Terminal
(PLC Adaptor
Add-on Unit)
Terminal
Additional
adaptors can
be added
later, for a total
of 16 adaptors
including the
master. See
the Operating
Instructions for
details.
1
2
PLC
LAN
MAST
ER
HD-
PLC
BL-P
A30
0
SETUP
PLC
LAN
MAST
ER
HD-
PLC
BL-P
A30
0
SET
UP
MASTER TERMINAL
MASTER TERMINAL
MASTER
TERMINAL
PLC
LAN
MASTER
(green) (orange) (green)
PLC
LAN
MASTER
(orange)
(off)
(green)
3
4
PLC
LAN
MAST
ER
HD-
PLC
BL-P
A30
0
SET
UP
PLC
LAN
MAST
ER
HD-
PLC
BL-P
A30
0
SET
UP
MASTER
connect to a
router or modem
connect to a
network device
TERMINAL
PLC
LAN
MASTER
(green)
(green)
(off)
PLC
LAN
MASTER
(green)
(green)
(green)
Recommended
Outlet
AC adaptor
Charger
Noise filter power strip
Not Recommended
Outlet
Noise filter power strip
Outlet
Outlet
AC adaptor
or charger
or
AC adaptor
or charger
This document is written to be used with the BL-PA300KTA, which is a pre-configured set
of 2 adaptors.
No settings are required to use these adaptors. Simply follow the instructions provided in
this document. Refer to the included Operating Instructions for safety, reconfiguration,
and troubleshooting information.
BL-PA300KTA_GS.book Page 1 Tuesday, June 24, 2008 4:20 PM