1. DL manuals
  2. Panasonic
  3. Blu-ray Player
  4. DMP-BD85EB
  5. Service Manual

Panasonic DMP-BD85EB Service Manual - 6 Operating Instructions

Summary of DMP-BD85EB

  • Page 1

    © panasonic corporation 2010 unauthorized copy- ing and distribution is a violation of law. Order no. Dsd1003011ce blu-ray disc player model no. Dmp-bd85eb dmp-bd85ee dmp-bd85ef dmp-bd85eg vol. 1 colour (k)...........Black type.

  • Page 2: Table of Contents

    2 table of contents page page 1 safety precaution -------------------------------------------------3 1.1. General guidelines ----------------------------------------3 1.2. Leakage current cold check ---------------------------3 1.3. Leakage current hot check (see figure 1.) --------3 2 warning -----...

  • Page 3: 1 Safety Precautions

    3 1 safety precautions 1.1. General guidelines 1. Important safety notice there are special components used in this equipment which are important for safety. These parts are marked by in the schematic diagrams, circuit board layout, exploded views and replacement parts list. It is essen- tial that t...

  • Page 4: 2 Warning

    4 2 warning 2.1. Prevention of electrostatic discharge (esd) to electrostatically sensitive (es) devices some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called elec- trostatically sensitive (es) devices. The following techniques shou...

  • Page 5

    5 2.2. Caution for ac cord (for eb) 2.2.1. Information for your safety important your attention is drawn to the fact that recording of pre- recorded tapes or discs or other published or broadcast material may infringe copyright laws. Warning to reduce the risk of fire or shock hazard, do not expose ...

  • Page 6

    6 2.3. Precaution of laser diode.

  • Page 7

    7 2.4. Service caution based on legal restrictions this service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the info...

  • Page 8

    8 2.5. Static electricity protection measures • the laser diode in the traverse unit (optical pick-up) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse unit (optical pick-up). 2.6...

  • Page 9: 3 Service Navigation

    9 3 service navigation 3.1. Service infomation this service manual contains technical information which will allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, this inf...

  • Page 10

    10 3.2. Caution for divx please will always pass the customer “warning for customers who use the divx video-on-demand content.” with the product and get it when you unavoidably exchange flash rom or p.C.B. Including flash rom (when the product is exchanged, it is the same.). You must use print attac...

  • Page 11: 4 Specifications

    11 4 specifications power supply: ac 220 - 240 v, 50 hz power consumption: approx. 27 w in standby mode: approx. 0.2 w in quick start standby mode: approx. 8.4 w operating temperature range: +5 °c to +35°c operating humidity range: 10 % to 80 % rh (no condensation) signal system: pal/ntsc video outp...

  • Page 12

    12 4.1. Others (licenses) security: wpa2-psk (tkip/aes) wpa-psk (tkip/aes) wep (64bit/128bit) (this unit supports wpa and wpa2 encryption.) solder: this model uses lead free solder (pbf). Note: specifications are subject to change without notice..

  • Page 13

    13 5 location of controls and components 1 turn the unit on and off 2 tv operation buttons you can operate the tv through the unit’s remote control. [ tv] : turn the television on and off [av] : switch the input select [ k l vol] : adjust the volume [ 9 : ch] : channel select 3 select title numbers,...

  • Page 14: 6 Operating Instructions

    14 6 operating instructions 6.1. Taking out the disc from bd drive unit when the disc cannot be ejected by open/close button 6.1.1. When the power can be turned off. 6.1.1.1. When the power can be turned off. 1. Turn the unit off, then press and hold [ok], [yellow] and [blue] buttons on the remote c...

  • Page 15

    15 6.2. Micro fuse conducting check this unit uses the micro fuse. Check the micro fuse conducting using the tester at the check points below..

  • Page 16

    16 7 multiple pressing function 7.1. About the multiple pressing of the unit’s remote control the remote control which included this unit is possible pressing multiple buttons simultaneously (multiple pressing function), and can operate for the customer's initial settings and the service mode, etc. ...

  • Page 17

    17 7.2.1. Open mode (remote cont. Buttons: [ok] [yellow] [blue]) when pressing the 3 buttons, [ok], [yellow] and [blue] simultaneously for 5 seconds, “00 ret” is displayed on the fl display..

  • Page 18

    18 7.2.2. Privately mode 1 (remote cont. Buttons: [6] [7] [yellow]) when pressing the 3 buttons, [6], [7] and [yellow] simultaneously for 5 seconds, “50 ret” is displayed on fl display. 7.2.3. Privately mode 2 (remote cont. Buttons: [5] [9] [red]) when pressing the 3 buttons, [5], [9] and [red] simu...

  • Page 19: 8 Service Mode

    19 8 service mode 8.1. About the service mode informations necessary for service can be displayed. 8.1.1. How to enter the service mode 8.1.2. How to exit the service mode press and hold the [power] button (remote control or unit). >>> the service mode is terminated and automatically turns the unit ...

  • Page 20

    20 8.2. Service mode list the display of information to each command is as follows. Note: do not use it excluding the designated command..

  • Page 21

    21.

  • Page 22

    22.

  • Page 23

    23 8.3. Self-diagnostics functions 8.3.1. Self-diagnostics functions self-diagnosis function provides information for errors to service personnel by self-diagnosis display when any error has occurred. U** and f** are stored in memory and held. You can check last error code by transmitting [0] [1] of...

  • Page 24

    24.

  • Page 25

    25.

  • Page 26: 9 Service Fixture & Tools

    26 9 service fixture & tools.

  • Page 27

    27 10 disassembly and assembly instructions 10.1. Unit 10.1.1. Disassembly flow chart the following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the ser- vicing. To assemble the unit, reverse the steps shown in the chart below. 10.1.2...

  • Page 28

    28 10.1.3. Top case 1. Remove the 2 screws (a) and 3 screws (b). 2. Slide top case rearward and open the both ends at rear side of the top case a little and lift the top case in the direction of the arrows. 10.1.4. Front panel 1. Unlock 7 tabs (a) - (g) turn. Pull with the front panel in the directi...

  • Page 29

    29 3. Confirm the tray door spring is attached as following. 10.1.6. Rear panel 1. Remove the 6 screws (a) and screw (b). 2. Unlock 2 locking tabs (a) to remove the rear panel. 10.1.7. Bdp/digital p.C.B. Module case 1: when replacing the pair of bd drive and digital p.C.B. (do not remove opu ffc and...

  • Page 30

    30 2. Remove the opu ffc, and isolate it with an esd pre- vention bag (rpfc0114). 3. Remove the 18 pin ffc. 4. Remove the wire with connector (a). 5. Remove the connector (b). 6. Remove the 4 screws (a) to remove bd drive. 7. Remove the 5 screws (b) to remove digital p.C.B.. Caution for assemble: wh...

  • Page 31

    31 10.1.9. Audio out p.C.B. 1. Remove the connector (a). 2. Remove the 3 screws (a) to remove audio out p.C.B.. 10.2. Bd drive 10.2.1. Upper base ass’y 1. Remove the 4 screws (a), and push the hook in. 2. Lift up the upper base ass’y, and pull it out to the direc- tion of arrow..

  • Page 32

    32 10.2.2. Tray 1. Perform the step “10. 2. 1. Upper base ass’y”. 2. Insert the paper clips, etc. Into the hole of the bottom side, and slide it to the direction of arrow until it can be. 3. Pull the tray to the direction of arrow until it can be. 4. Insert the paper clips, etc. Into the hole of the...

  • Page 33

    33 10.2.4. Slide cam 1. Perform the step “10. 2. 3. Pulley gear, belt”. 2. Remove the sheet. 3. Disconnect the 3 ffcs. 4. Remove the 2 screws (b) and the angle. 5. Remove the drive p.C.B.. Caution: though the drive p.C.B. Is not supplied as replace- ment parts, it must be removed for after disassem-...

  • Page 34

    34 10.2.6. Grease.

  • Page 35

    35 10.2.7. How to clean the lens of the optical pick-up after performing the step “10. 2. 1. Upper base ass'y”, clean the lens of the optical pick-up..

  • Page 36

    36 10.2.8. How to clean up the turntable when “noread” is displayed in fl display, clean up the turntable according to the following steps. 1. Blow the dust from the turntable in the blower. (do not strongly blow it.) 2. Put one drop of isopropyl or ethyl alcohol to clean cotton swab. (using a fresh...

  • Page 37

    37 11 measurements and adjustments for description of the disassembling procedure, see the “10 disassembly and assembly instructions”. 11.1. Service positions 11.1.1. Checking and repairing of power p.C.B..

  • Page 38

    38 11.1.2. Checking and repairing of audio out p.C.B..

  • Page 39

    39 11.1.3. Checking and repairing of bdp/digital p.C.B. Module.

  • Page 40

    40 11.2. Adjustment of bdp/digital p.C.B. Module 11.2.1. Checking out symptoms and repair of bdp/digital p.C.B. Module when replacing or repairing the bd drive unit alone or the digital p.C.B. Alone, please perform the work according to following checking sequence..

  • Page 41

    41 11.2.2. In the case of necessity the adjustment 1. When the bd drive is replaced. 2. When the digital p.C.B. Is replaced. 11.2.3. List of service tools 11.2.3.1. Adjustment/inspection tools 11.2.3.2. Commercial tools required 11.2.4. How to adjust the bdp/digital p.C.B. Module the adjustment may ...

  • Page 42

    42 1. Connect the serial cable (rfkz0139) between serial port connector (p51601) on the digital p.C.B. And pc's serial port. • confirm the pc’s serial port number (com1, com2, etc.) connected to serial cable (rfkz0139), the port number may be set after this procedure. 2. Start the adjustment softwar...

  • Page 43

    43 [the diag adjustment (sd diag) start] 9. When below message displayed, perform followings: a. Insert the sd diag card to sd card slot. B. Set the rfkz0139 sw into “on”. C. Click the [ok] button. 10. When below message displayed, perform followings: a. Connect the power cable to the unit. B. Press...

  • Page 44

    44 [bd-rom adjustment] 17. When the following message is displayed, set the bd- rom test disc (vff0396) on the tray, then click the [ok] button. When clicking the [ok] button, the tray is automatically closed. After a while the fl display displays “adj3” and automatically begins adjustment. When the...

  • Page 45

    45 [finishing the drive adjustment] 21. When below message displayed, perform followings: a. Confirm “p off” is displayed at the fl display. B. Disconnect the power cord from the unit. C. Click the [ok] button. 22. Click the [exit] button. 23. Click the [exit] button. 24. Click the [exit(e)] button....

  • Page 46

    46 11.3. Caution for replacing parts after replacing the digital p.C.B., [test] is displayed, so, once power off again to on. 11.3.1. Caution after replacing parts after replacing the bdp/digital p.C.B. Module, must be update firmware. 11.3.2. Standard inspect specifications after repairs after maki...

  • Page 47: Service Manual

    S-1 s1. About indication of the schematic diagram ............................ S-1 s1.1. Important safety notice......................................................... S-1 s2. Voltage and waveform chart ................................................... S-2 s2.1. Front p.C.B. .......................

  • Page 48

    S-2 s2. Voltage and waveform chart s2.1. Front p.C.B. Note) indicated voltage values are the standard values for the unit measured by the dc electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the i...

  • Page 49

    S-3 s3. Block diagram s3.1. Power supply block diagram dmp-bd85 power supply circuit block diagram f1001 p1001 (ac socket) a n va1001,l1001 d1006,c1014 surge suppressor and surge absorber rectifier 1 2 3 12 16 12 1 15 11 10 9 1 2 3 8 7 5 6 t1001 (power transformer) 7 1 4 9 5 2 ic1021 (switching ic) ...

  • Page 50

    S-4 s3.2. Timer block diagram dmp-bd85 timer circuit block diagram ic57001 (timer) 9 8 10mhz out 10mhz in x57001 (10mhz) tbus txd tbus rxd tbus clk 15 16 17 dr pfail[l] sp save l sp save l g key3 g key1 g key2 g remocon g fl txd g fl clk g fl cs remocon 60 7 31 59 ic7001 (vfd driver) p1102 3 p58001 ...

  • Page 51

    S-5 s3.3. Analog video/audio block diagram ic57001 (timer) ic51001 (bp1 lsi) dmp-bd85 analog video/audio circuit block diagram ic53001 (video driver) ic54003 (audio d/a converter) 1 svdaco3 sync tip clamp lpf 6.75mhz logic mute ctrl lpf 13.5mhz lpf 30mhz 3 sync tip clamp vin pyin lpf 13.5mhz lpf 30m...

  • Page 52

    S-6 s4. Schematic diagram s4.1. Interconnection diagram dmp-bd85 interconnection diagram p7001 1 gnd 2 fl_txd 3 fl_clk 4 fl_cs 5 x_sw3r3v 6 gnd p1001 1 a 2 n p1102 fan_pwr 1 fan_lock 2 sp_save_l 3 pw_x_sw12r2v 4 pw_x_sw12r2v 5 pw_x_sw12r2v 6 gnd 7 gnd 8 pw_x_sw5r9v 9 pw_x_sw5r9v 10 pw_x_sw5r9v 11 fl...

  • Page 53

    S-7 s4.2. Front schematic diagram s-7 confidential until $(0.01) c7203 c 7 2 0 2 f 1 h 1 a 1 0 5 a 0 2 8 1 0 v r7208 $(10k) 33 r7205 2200 r7203 * r7207 r7202 6200 r7201 $(0) 1 2 * pj7204 1 2 * pj7203 c 7 2 0 1 $ [ f 2 a 0 j 4 7 0 a 2 4 5 ] 1 8 6 4 2 3 5 7 9 1 0 k 1 k a 1 0 b 0 0 1 9 6 p 7 2 0 1 1 5 ...

  • Page 54

    S-8 s4.3. Power_wide (p) schematic diagram confidential until 10[22] r1029 r1028 10[22] r1022 * r1145 d1bfr0270001 2 7 k [ d ] r 1 1 3 8 2 7 k [ d ] r 1 1 3 6 5600[g] r1144 33k[g] r1131 2700[g] r1132 4 7 0 k [ d ] r 1 1 4 3 8 2 k [ g ] r 1 1 4 2 r 1 1 4 1 2 2 0 k 4 7 0 k [ d ] r 1 1 3 7 4 7 0 k [ d ...

  • Page 55

    S-9 confidential until 10[22] r1029 r1028 10[22] r1022 * r1145 d1bfr0270001 2 7 k [ d ] r 1 1 3 8 2 7 k [ d ] r 1 1 3 6 5600[g] r1144 33k[g] r1131 2700[g] r1132 4 7 0 k [ d ] r 1 1 4 3 8 2 k [ g ] r 1 1 4 2 r 1 1 4 1 2 2 0 k 4 7 0 k [ d ] r 1 1 3 7 4 7 0 k [ d ] r 1 1 3 9 erds2tj470t r1174 r1173 560...

  • Page 56

    S-10 confidential until 10[22] r1029 r1028 10[22] r1022 * r1145 d1bfr0270001 2 7 k [ d ] r 1 1 3 8 2 7 k [ d ] r 1 1 3 6 5600[g] r1144 33k[g] r1131 2700[g] r1132 4 7 0 k [ d ] r 1 1 4 3 8 2 k [ g ] r 1 1 4 2 r 1 1 4 1 2 2 0 k 4 7 0 k [ d ] r 1 1 3 7 4 7 0 k [ d ] r 1 1 3 9 erds2tj470t r1174 r1173 56...

  • Page 57

    S-11 confidential until 10[22] r1029 r1028 10[22] r1022 * r1145 d1bfr0270001 2 7 k [ d ] r 1 1 3 8 2 7 k [ d ] r 1 1 3 6 5600[g] r1144 33k[g] r1131 2700[g] r1132 4 7 0 k [ d ] r 1 1 4 3 8 2 k [ g ] r 1 1 4 2 r 1 1 4 1 2 2 0 k 4 7 0 k [ d ] r 1 1 3 7 4 7 0 k [ d ] r 1 1 3 9 erds2tj470t r1174 r1173 56...

  • Page 58

    S-12 s4.4. Fl (fl) schematic diagram confidential until 8 6 4 2 1 5 7 9 32 31 28 25 26 22 18 20 21 19 24 23 27 29 16 13 14 11 10 12 15 17 a2bd00000188 dp7001 zb7001 * c7006 f1h1c104a071 16v c 7 0 0 4 f 1 h 1 c 1 0 4 a 0 7 1 16v c7005 f1h1h104a783 5 0 v r7009 100k pw-15v pw-21v pw-18v fan_lock fan_pw...

  • Page 59

    S-13 s4.5. Open_sw schematic diagram / s4.6. Power_sw schematic diagram confidential until 1 2 $[rez1969] pj7551 s7551 evq11a05r 2pin flat cable 2.5mm pitch k e y _ p o w e r g n d power_sw 2010/06/30 rez1969:m1800(others) rez1926:m1820 rez1970:m1800(us) 1 2 $[rez1927￨rez1929] pj7581 evq11a05r s7581...

  • Page 60

    S-14 s4.7. Audio main schematic diagram confidential until f 2 a 0 j 4 7 0 a 5 9 9 c 4 0 2 6 6 . 3 v c4022 f2a1e470a205 25v c4013 f2a1e470a205 25v c4010 f2a1c470b174 16v c4011 f2a1e470a205 25v c4012 f2a1e470a205 25v c4014 f2a1c470b174 16v f 2 a 1 c 1 0 1 b 2 9 9 c 4 0 0 2 1 6 v c 4 0 0 9 f 2 a 1 e 2...

  • Page 61

    S-15 confidential until f 2 a 0 j 4 7 0 a 5 9 9 c 4 0 2 6 6 . 3 v c4022 f2a1e470a205 25v c4013 f2a1e470a205 25v c4010 f2a1c470b174 16v c4011 f2a1e470a205 25v c4012 f2a1e470a205 25v c4014 f2a1c470b174 16v f 2 a 1 c 1 0 1 b 2 9 9 c 4 0 0 2 1 6 v c 4 0 0 9 f 2 a 1 e 2 2 1 a 6 4 3 2 5 v f 2 a 1 e 2 2 1 ...

  • Page 62

    S-16 confidential until f 2 a 0 j 4 7 0 a 5 9 9 c 4 0 2 6 6 . 3 v c4022 f2a1e470a205 25v c4013 f2a1e470a205 25v c4010 f2a1c470b174 16v c4011 f2a1e470a205 25v c4012 f2a1e470a205 25v c4014 f2a1c470b174 16v f 2 a 1 c 1 0 1 b 2 9 9 c 4 0 0 2 1 6 v c 4 0 0 9 f 2 a 1 e 2 2 1 a 6 4 3 2 5 v f 2 a 1 e 2 2 1 ...

  • Page 63

    S-17 confidential until f 2 a 0 j 4 7 0 a 5 9 9 c 4 0 2 6 6 . 3 v c4022 f2a1e470a205 25v c4013 f2a1e470a205 25v c4010 f2a1c470b174 16v c4011 f2a1e470a205 25v c4012 f2a1e470a205 25v c4014 f2a1c470b174 16v f 2 a 1 c 1 0 1 b 2 9 9 c 4 0 0 2 1 6 v c 4 0 0 9 f 2 a 1 e 2 2 1 a 6 4 3 2 5 v f 2 a 1 e 2 2 1 ...

  • Page 64

    S-18 s5. Print circuit board ibt1 w 7 5 2 w 7 5 4 w755 w 7 5 3 w757 w 7 5 6 w 7 5 8 w751 r7205 r7201 c 7 2 0 3 r7207 r7202 r 7 2 0 8 c7202 r7203 w 7 0 3 w 7 0 2 w 7 0 1 s7206 s7202 c 7 2 0 1 d7201 1 2 pj7204 1 2 p j 7 2 0 3 3 2 1 ir7201 1 2 6 5 p7202 1 2 10 9 p7201 dmp-bd85eg/ef/eb/ee front p.C.B. 1...

  • Page 65

    S-19 s5.2. Power p.C.B. W24 w 2 1 w18 w19 w17 w28 w 1 3 w 1 1 w 2 6 w 4 3 w 4 5 w41 w29 w 7 w 6 w8 w1 w4 w34 w44 w40 w39 w31 w30 w35 w36 w38 w 9 w3 w2 w33 w 2 7 w46 w37 w 4 2 w22 w16 w12 w10 w 2 3 w20 w25 w32 w 5 w15 w14 c1021 1 2 1 1 1 0 9 8 7 6 5 2 1 3 t 1 0 0 1 z a 1 1 1 2 d1029 c 1 1 2 5 d 1 1 7...

  • Page 66

    S-20 s5.2.2. Power p.C.B. (foil side) 6. 2 3.5 6 . 2 6 . 2 3.5 3.5 3.5 3.5 i b t 1 3 w 2 0 1 r 1 1 7 2 r 1 0 1 9 d1023 c k a a 8 c k a a 1 2 c k a a 1 1 c k a a 6 c k a a 1 c k a a 2 c k a a 3 r1118 r1119 r 1 1 1 5 3 2 4 1 ic1102 c 1 1 2 4 c 1 1 1 4 r 1 1 1 4 r 1 1 1 3 r 1 1 1 6 r1104 r 1 1 1 1 c 1 ...

  • Page 67

    S-21 s5.3. Open_sw p.C.B. / s5.4. Power_sw p.C.B. S 7 5 8 1 1 2 pj7581 (foil side) s7551 1 2 p j 7 5 5 1 (component side) dmp-bd85eg/ef/eb/ee open_sw p.C.B. 10 9 8 7 6 5 4 3 2 1 g f e d c b a (foil side) (component side) dmp-bd85eg/ef/eb/ee power_sw p.C.B..

  • Page 68

    S-22 s5.5. Audio_out p.C.B. R 4 0 4 2 qr4002 qr4001 c k a b 4 0 1 3 r4032 c 4 0 2 5 r 4 0 3 0 c4027 c4030 r4033 r 4 0 2 6 q4008 c 4 0 2 4 c 4 0 2 8 r4028 l b 4 0 0 1 r 4 0 2 9 r 4 0 2 7 q4009 r 4 0 3 1 tl4002 r 4 0 0 1 tl4001 r4025 r 4 0 2 4 r4023 r4022 r4021 r4020 r 4 0 1 9 r 4 0 1 8 r4017 r4016 r ...

  • Page 69: S6. Abbreviation

    S6. Abbreviation s-23 abbreviations a a0~up address aclk audio clock ad0~up address bus adata audio pes packet data ale address latch enable amute audio mute areq audio pes packet request arf audio rf asi servo amp inverted input aso servo amp output async audio word distinction sync b bck bit clock...

  • Page 70

    S-24 abbreviations initial/logo dreq data request dresp data response dsc digital servo controller dslf data slice loop filter dvd digital video disc e ec error torque control ecr error torque control reference encsel encoder select etmclk external m clock (81mhz/40.5mhz) etsclk external s clock (54...

  • Page 71

    S-25 abbreviations initial/logo pwmda pulse wave motor drive a pwmoa, b pulse wave motor out a, b r re read enable rfenv rf envelope rfo rf phase difference output rs (cd-rom) register select rsel rf polarity select rst reset rsv reserve s sbi0, 1 serial data input sbo0 serial data output sbt0, 1 se...

  • Page 72

    S-26 abbreviations initial/logo trcrs track cross signal tron tracking on trson traverse servo on v vblank v blanking vcc collector power supply voltage vcdcont video cd control (tracking balance) vdd drain power supply voltage vfb video feed back vref voltage reference vss source power supply volta...

  • Page 73

    S7. Replacement parts list s-27 e.S.D. Standards for electrostatically sensitive devices, refer to “prevention of electrostatic discharge (esd) to electrostatically sensitive (es) devices” section. 1.* be sure to make your orders of replacement parts according to this list. 2. Important safety notic...

  • Page 74

    Dmp-bd85 vol.1 ref.No. Part no. Part name & description pcs remarks ref.No. Part no. Part name & description pcs remarks c1176 f2a1c221b111 16v 220u 1 ## vep70323c front p.C.B. 1 (rtl) e.S.D. C7004 f1h1c104a071 16v 0.1u 1 ## vep71169e power p.C.B. 1 (rtl) e.S.D. C7005 f1h1h104a783 50v 0.1u 1 ## vep7...

  • Page 75

    Dmp-bd85 vol.1 ref.No. Part no. Part name & description pcs remarks ref.No. Part no. Part name & description pcs remarks r1118 erj3rbd331v 1/16w 330 1 c4027 f1h1c104a071 16v 0.1u 1 r1119 erj3rbd183v 1/16w 18k 1 c4028 f1h1c104a071 16v 0.1u 1 r1131 erj3geyg333v 1/10w 33k 1 c4030 f1h1c104a071 16v 0.1u ...

  • Page 76

    Dmp-bd85 vol.1 ref.No. Part no. Part name & description pcs remarks ref.No. Part no. Part name & description pcs remarks 70 rhd30119-l screw 1 1 rkm0605a-kj top case 1 71 rhd30119-l screw 1 3 vee1h06 power cable 1 72 xsn3+4fj screw 1 4 vep70323c front p.C.B. 1 (rtl) e.S.D. 73 rhd30105-1 screw 1 5 ve...

  • Page 77

    Dmp-bd85 vol.1 ref.No. Part no. Part name & description pcs remarks ref.No. Part no. Part name & description pcs remarks 101 vql1v70 laser caution label 1 102 vma0v86 yoke 1 103 vmd5751 upper base 1 104 vmd5752-1j drive gear 1 105 vmt1981 dust cover a 1 106 vmz3737-j clamp cover 1 107 vxa8619 tray u...

  • Page 78

    Dmp-bd85 vol.1 ref.No. Part no. Part name & description pcs remarks ref.No. Part no. Part name & description pcs remarks a1 rja0043-1c ac power supply cord 1 eg,ee,ef a1 k2cz3yy00005 ac power supply cord 1 eb a3 n2qakb000077 remote control 1 a3-1 100300055200 battery cover 1 a5 vqt2h79 operating ins...

  • Page 79: S8. Exploded View

    S8. Exploded view s8.1. Frame and casing section s-33 a a 51 49 52 75 76 74 73 41 42 43 45 44 53 50 48 60 61 58 59 47 66 67 68 69 70 72 71 46 17 15 16 14 12 11 9 3 30 5 10 19-1 19-2 19-3 19-4 19-4-2 19-4-3 19-4-1 19-5 65 64 63 62 77 78 79 80 19 27 4 26 24 28-2 28-1 28-3 28 55 57 56 23 21 25 22 20 13...

  • Page 80

    S8.2. Mechanism section s-34 101 123 122 112 119 125 124 128 127 126 129 106 102 104 105 107 108 103 109 110 111 120 113 115 114 117 121 116 118.

  • Page 81

    S8.3. Packing parts and accessories section s-35 a7 a3-1 a3 a6 a5 a1 battery (remote cont.) pc4 pc3 pc5 pc1 pc2 pc7 (eg) pc8 (eb/ee/ef).