Operating instructions blender (household use) table of contents safety precautions ••••••••••••••••••••••••••••••••••••••2 parts ••••••••••••••••••••••••••••••••••••••6 how to use blender ••••••••••••••••••••••••••••••••••••8 how to use dry mill •••••••••••••••••••••••••••••••••• 11 safety lock •••...
2 ﺭﺍﺩﺷﻫ ﻪﻳﺑﻧﺗ ﺭﺍﺩﺷﻫ ■ ■ ■ ■ ■ ■ safety precautions always follow these precautions in order to prevent the risk of danger to the users of this product or those nearby, and damaging property, be sure to follow the safety precautions outlined below. ■ the following signs are used for precautions. They...
3 ﺭﺍﺩﺷﻫ warning this product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible their safety. ...
4 ﺭﺍﺩﺷﻫ ﻪﻳﺑﻧﺗ warning caution please make sure that voltage used for this product is suitable to the local area voltage. Never use hot water (over 60 °c) for cleaning purpose or for drying it. Care shall be taken when handling the sharp cutting blades, emptying the container and during cleaning. If ...
5 ﻪﻳﺑﻧﺗ remove packing materials, such as plastic bags or plug cap etc from the appliance. Discard them or keep them away from babies and children. （ otherwise it may cause suffocation.） ﺵﻮﭘﺭﺩ ﺎﻳ ﯽﮑﻴﺘﺳﻼﭘ یﺎﻫ ﻪﺴﻴﮐ ﻞﻴﺒﻗ ﺯﺍ یﺪﻨﺑ ﻪﺘﺴﺑ ﺩﺍﻮﻣ .ﺪﻳﺭﺍﺩﺮﺑ ﻩﺎﮕﺘﺳﺩ ﺯﺍ ﺍﺭ ﻩﺮﻴﻏ ﻭ ﺮﻴﮕﺧﺍﺭﻮﺳ .ﺪﻳﺭﺍﺩ ﻪﮕﻧ ﻥﺎﮐﺩﻮﮐ ﺱﺮﺘﺳﺩ ﺯﺍ...
Switch buttons rotates only while the button is being pressed)”, 開關 馬達罩 乾磨器 乾磨器容器 乾磨器 乾 乾.
7 • • • to disassemble blender to disassemble mill to assemble blender to assemble mill mill container base mill gasket turn blender container base counterclockwise to disassemble. Twist the mill container base counterclockwise. Turn blender container clockwise to assemble. • make sure that gasket i...
8 • • • • • • • how to use blender cautions: • first, dice the ingredients (cut them into cubes measuring 1 to 2 cm), and put them in water. • put the ingredients in the container starting with the softer ones • do not place ingredients with a maximum total volume ml • do not put the following kinds...
9 1 2 place the ingredients in the blender container. Check that the cover is in place to prevent the ingredients from out. Mount the blender container on the motor housing. Twist the container clockwise until it locks into place. When adding ingredients or seasonings, remove/attach inner cap whilst...
10 3 blended, power outlet. Twist when disconnecting the power plug, be absolutely sure to take hold of the molded plug. Never pull on the cord. After the ingredients have been disconnect the power plug from the the blender container counterclockwise to remove it from the motor housing, and take out...
乾磨器的使用方法 ﻒﻔﺠﻤﻟﺍ 20 20 2 2.
12 1 2 outlet. Turn the mill container upside down, and place the ingredients in it. Twist the mill container base clockwise until it locks into place, and mount it onto the mill container. Place the mill container and mill container base on the motor housing. Twist the container and base clockwise ...
13 3 mixed the power outlet. Remove wait for the mill to stop rotating before removing your hand. When disconnecting the power plug, be absolutely sure to take hold of the molded plug. Never pull on the cord. After the ingredients have been disconnect the power plug from the mill container base from...
14 safety lock the safety lock has been designed to prevent the blender from switching on when container is not properly in place. Do not push the safety lock pin with any implement, stick etc. G n ir u d d e h s u p s i e s a b r e n i a t n o c e h t f o k c a b e h t n o n i p y t e f a s e h t n...
15 1 2 3 one-at-a-time in order: > 切削刀 > . And then press the following buttons reduce the amount of the ingredients inside the container by half. Circuit breaker protection if the motor is subjected to an excessive load, its protection device is tripped, shutting down the motor automatically. It is...
16 • • • • • • • how to clean notes: • before cleaning the blender, disconnect the power plug from the power outlet. • handle the cutter carefully. • to clean the parts, use cold or lukewarm water and a soft sponge. • do not use steel brushes or other abrasive cleaning materials or utensils. • do no...
17 wash the parts using a soft sponge soaked in diluted kitchen detergent (neutral). To remove ingredients stuck in the cutter, carefully clean it with a brush. Then rinse thoroughly with water, and allow the parts to dry out. Carefully clean mill cutter with a brush. Do not use water. Wipe with a w...
18 problems possible cause page the blender does not operate • • • • • • • troubleshooting see p.9 & p.12 the blender stops operating midway through operation. • the circuit breaker protection of the motor has been tripped. Check whether prohibited, hard or too many ingredients have been placed in t...
Note in case of failure or damage you can identify the date of manufacturing by number which is marked on bottom side of the unit. Number marked on bottom side of the unit: x x x x x x fifth and sixth digits: day (in number) 01, 02, 03...31 third and fourth digits: month (in number) 01--january, 02-...
Mx-gx1561: 220 w / mx-gx1511: 230 w 厘米 厘米 厘米 / 220 v 50 hz web site: http://www.Panasonic.Com x0921-351 approx. 1.8 kg mx-gx1561: approx. 3.4 kg mx-gx1511: approx. 2.2 kg :mx-gx1561 :mx-gx1511 / :mx-gx1561 :mx-gx1511 / 乾磨器 千克 千克 千克.
