Panasonic QE-TS101AA Owner's Manual
3
2
1
4
5
6
7
8
Thank you for choosing Panasonic.
Before using the product, be sure to read this “Owner’s manual” and follow
the instructions to use the product correctly.
After reading the owner’s manual, store it in a handy location for future refer-
ence.
In addition, observe all warnings and cautions on the product.
QE-TS101AATR
S1113-0
Owner’s Manual
Wireless Charging Pad
Model No.
QE-TS101AA
Wireless Charging Pad
Warning
WARNING alerts to a potentially hazardous
situation. If not avoided it could result in
death or serious injury.
Caution
CAUTION alerts to a potentially hazardous
situation. If not avoided it may result in minor
or moderate injury.
Warning
Be sure your device is Qi-compatible. If a non-Qi-compatible
device is used, it may overheat and rupture.
Do not disassemble the wireless charging pad or AC adapter.
Connect AC adapter only to a power source that has a voltage of
AC 100 V to AC 240 V.
Be sure to unplug the AC adapter from the electrical outlet before
cleaning this product.
Do not throw the product into a fire.
Do not use or leave this product in a hot location (near a fire or
other heat sources, in the hot sun, and so on) or in a location
where flammable gas is produced.
Do not charge a device using procedures other than as specified.
Do not disassemble, modify, repair, or solder the product. Our
company is not responsible for any problems resulting from such
actions.
Do not allow water or other liquid to contact the product. Never
use outdoors, with wet hands, or in a location where water, pet
urine, or other liquid may contact the product. If the product
becomes wet, immediately unplug it from the power source and
stop using it.
Do not place the product in a cooking appliance, such as a
microwave oven, or the like.
Do not drop or throw the product, or subject it to strong shocks.
Keep out of the reach of children. Accidents, such as choking
from mistakenly swallowing small parts, or injury could result.
Never use the product if damaged or if any problem, such as
deformation or damage due to dropping, is found.
Do not use the product if the cable of the wireless charging pad’s
AC adapter is damaged.
Do not touch the product during a lightning storm.
Do not place heavy objects on the cable of the wireless charging
pad’s AC adapter.
Do not use a voltage converter (travel adapter).
Do not plug or unplug the wireless charging pad’s AC adapter
with wet hands.
If the charging is not completed within the specified charging
time, stop the charging process.
Use the specified power source and voltage.
If you have an electrical device, such as an implanted cardiac
pacemaker or an implanted cardioverter-defibrillator, consult
a physician before using this product. Radio waves from the
product could adversely affect the operation of electronic medical
devices.
When inserting the power plug of the wireless charging pad’s AC
adapter into an electrical outlet, fully insert the plug.
When using this product to charge a Qi-compatible device,
remove any covers.
Do not touch the connection terminals of the wireless charging
pad’s AC adapter with your hands, fingers, or other parts of your
body.
Periodically wipe off any dust from the power plug.
Do not cover or wrap the product in a blanket or other bedding
during charging.
Remove the power plug from the electrical outlet before cleaning
the product.
Do not affix any metallic items, such as stickers or items that
contain metal, to the surface of the product or surface of the non-
slip cushions or to the battery cover, rear cover, or battery pack
of the Qi-compatible device.
Do not place any metallic items, such as straps or clips that contain
metal, between the surface of the product or surface of the non-slip
cushions and the Qi-compatible device or battery pack.
Do not allow any conductive object, such as metal parts or pencil
lead, to contact, be inserted in, or short-circuit the connection
terminals of the wireless charging pad’s AC adapter.
Do not use the wireless charging pad’s AC adapter while the
cable is still bundled.
Chocking hazard. Non-slip cushions can pose a chocking hazard.
Keep them away from children that may play with them.
Caution
If the product will be used by children, the proper handling should
be explained by a parent or other adult to avoid dangerous
situations. In addition, closely supervise children to ensure that
they are using the product as intended. Injury or other problem
could result.
Do not store the product in direct sunlight, such as in an
automobile, etc., in a hot or extremely cold location, or in a
location with high humidity or a large amount of dust.
Place the product on a flat, sturdy, level surface during charging.
If the product is placed on an uneven or unstable surface, it could
fall, resulting in damage. In addition, do not cover or wrap the
product in a cloth, blanket, or other bedding.
If any abnormality, such as smoke, unusual odor or noise, or
excessive heat, is noticed during use, or if the product was
dropped, became wet, or is damaged, immediately unplug the
product from the power source and contact the service.
Overheating may occur if foreign objects are put on the charge
pad and the non-slip cushions. Do not put any foreign object on
the charging pad and the non-slip cushions.
1.
Insert the power plug of the wireless charging
pad’s AC adapter into an electrical outlet.
2.
Insert the DC connector of the wireless charging
pad’s AC adapter into the DC input jack of the
wireless charging pad.
3.
Place the Qi-compatible device on the wireless
charging pad, making sure to position the
specified charging area* of the device at the center
of the wireless charging pad. Charging starts
when the LED indicators illuminate in blue.
* For the specified charging area of a Qi-
compatible device, refer to the user’s
manual of the device.
z
If the Qi-compatible device is not
recognized, slide the device back and forth
until it is positioned in a location where the
LED indicators come on in blue.
z
If the LED indicators come on in orange,
the Qi-compatible device is positioned
outside of the charging area. The orange indicators become brighter
as the device is moved closer to the charging area and become blue
when the device is in the charging area.
4.
When charging is complete, the LED indicators go off.
z
The product will start charging the Qi-compatible device again in
approximately 1 hour after completion of charging if it is left as is, but
it is normal.
5.
Remove the Qi-compatible device from the
wireless charging pad.
z
To charge another Qi-compatible device, wait approximately 15
seconds after the LED indicators go off before starting to charge
the next device. If you do not wait 15 seconds, the device may
not be charged correctly.
Power plug
(connection
terminal)
DC input jack
(connection terminal)
DC connector (connection terminal)
Wireless
Charging Pad
AC Adapter
LED indicators
LED Indicator
Non-Slip Cushions
z
Please make sure that the foreign object such as dust or any
metal object is not on the charging pad when you attach the non-
slip cushions.
z
Abnormal charge may cause the fire, burn or injury in case that
there is foreign object on the charging pad and the non-slip
cushions.
Using Non-Slip Cushions
: Position to attach non-slip cushions
Attach the non-slip cushions to the charge pad as shown to
prevent the device you are charging from slipping off the pad.
Indication
Color
State
Come on, and then dim after
approx. 10 seconds
Blue
Charging
Go off
-
Charging is complete (or Qi-
compatible device is not recognized)
Come on*
Orange
Qi-compatible device is being
recognized (outside of charging area)
Flash quickly
(at approx. 0.2-second intervals)
Blue
Charging error or malfunction
Flash slowly (come on for
approx. 2 seconds, and then go
off for approx. 1 second)
Blue
Temperature of Qi-compatible
device is too high or too low
* If the orange indicators do not become blue, or if the LED indicators flash quickly
in blue (at approximately 0.2-second intervals), the Qi-compatible device is not
recognized. Slide the Qi-compatible device back and forth and to the left and right
until it is positioned in a location where the LED indicators come on in blue.
If the LED indicators come on in orange, and then go off after approximately 3 sec-
onds, the wireless charging pad is reacting to a metal portion of the Qi-compatible
device. Slide the Qi-compatible device back and forth and to the left and right until
it is positioned in a location where the LED indicators come on in blue.
Troubleshooting
Check the items of the table below.
Symptoms
Causes
Corrective actions
Cannot charge
(LED indicators
do not come on)
You are not using the
specified AC adapter.
Use the included AC adapter.
The power plug and
connector of the AC adapter
are not inserted completely.
Fully insert the power plug and
connector.
There is a foreign object
between the wireless
charging pad and the Qi-
compatible device.
Remove the foreign object.
The charging of the Qi-
compatible device is
complete or nearly complete.
The charging is already complete.
You can remove and use the
device.
The Qi-compatible device is
not recognized correctly.
Slide the Qi-compatible device
back and forth and to the left
and right until it is positioned in a
location where the LED indicators
come on in blue.
The Qi-compatible device is
not positioned in the correct
direction.
Refer to the owner’s manual of
the Qi-compatible device and
position the device in the correct
direction.
Cannot charge
(LED indicators
flash quickly in
blue)
You are not using the
specified AC adapter.
If the condition does not change
when you use the included AC
adapter, remove the power plug
from the electrical outlet, wait a
few seconds, and then insert the
plug back into the outlet.
There is a foreign object
between the wireless
charging pad and the Qi-
compatible device.
Remove the foreign object.
The Qi-compatible device is
not recognized correctly.
Remove the Qi-compatible
device, wait until the LED
indicators go off, and then
position the device on the
wireless charging pad in a
location where the LED indicators
come on in blue.
Cannot charge
(LED indicators
come on in
orange)
The Qi-compatible device is
not positioned in the charging
area.
Slide the Qi-compatible device
back and forth and to the left
and right until it is positioned in a
location where the LED indicators
come on in blue.
There is a foreign object
between the wireless
charging pad and the Qi-
compatible device.
Remove the foreign object.
Cannot charge
(LED indicators
flash slowly in
blue)
The temperature of the Qi-
compatible device is too high
or too low.
Leave the Qi-compatible device in a
location with a temperature of 41°F
(5°C) - 95°F (35°C) for a while, and
then charge the device.
Symptoms
Causes
Corrective actions
Charging time is
long (compared
to the charging
time for other
Qi-compatible
devices when
using this
wireless charging
pad)
The temperature of the
charging location is too high
or too low.
Charge the device in a location
that is at room temperature.
However, the charging time may
be long depending on the type
of Qi-compatible device even
if the temperature is within the
operating temperature range.
The Qi-compatible device is
being used during charging.
If the Qi-compatible device
is used during charging, the
charging time may become
longer.
The Qi-compatible device
was moved from the location
where the LED indicators
came on in blue.
Remove the Qi-compatible device, wait
approximately 15 seconds, and then
position the device on the wireless
charging pad in a location where the
LED indicators come on in blue.
Charging stops
before being
completed
(wireless
charging pad)
The Qi-compatible device
was moved during charging.
Remove the Qi-compatible
device, wait approximately 15
seconds, and then position the
device on the wireless charging
pad in a location where the LED
indicators come on in blue.
Charging is not
completed
(with the Qi-
compatible
device fully
charged or totally
discharged)
This is a specification.
It is normal.
Refer to the note (*) below.
Charging of
the product
is already
complete, but the
Qi-compatible
device is not fully
charged or totally
discharged
The Qi-compatible device is
on (powered on, display on,
application started, etc.).
The Qi-compatible device will
not be fully charged if the Qi-
compatible device is on (powered
on, display on, application started,
etc.).
* Some Qi-compatible devices may not allow the product to detect a fully charged
state (because of not transmitting the corresponding signal). In this case, the prod-
uct’s LED indicators are continuously on in blue to indicate a fully charged state,
but it is normal. For the impact of charging continuously in this state on the Qi-
compatible device, contact the device manufacturer.
Wireless Charging Pad
AC Adapter
Model
QE-TS101AA
QE-AP105AA
Input
DC 12 V 650 mA
AC 100-240 V 50-60Hz 0.21 A
Output
Max. 5 W
DC 12 V
650 mA
Dimensions
Approx. Ф 3-5/8 in
(93 mm) × 5/8 in (16 mm)
Approx. 2-3/4 in (70.5 mm) × 1-1/4 in
(30.5 mm) × 1-3/4 in (45 mm)
(excluding protrusions and cable)
Cable length
-
Approx. 77-1/2 in (197 cm)
Weight
Approx. 3 oz (85 g)
Approx. 4-3/8 oz (125 g)
Operating
temperature
41°F (5°C) - 95°F (35°C)
Operating
humidity
45% - 85%
z
Due to product improvements, the specifications and external
appearance are subject to change without notice.
UL Wording
IMPORTANT SAFETY INSTRUCTIONS-Save These
Instructions
DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS
Caution
Risk of injury. Risk of electric shock and fire.
For indoor use only. Dry location use only.
For connection to a supply not in the U.S.A., use an attachment
plug adapter of the proper configuration for the power outlet, if
needed.
Specifications
FCC Wording
z
This device complies with Part 15 and 18 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party: Panasonic Corporation of North America Two
Riverfront Plaza Newark, NJ 07102-5490
Support Contact: Panasonic Consumer Electronics Company
Telephone No.:1-201-348-7000
Note:
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver in connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product may cause interference to radio equipment and should
not be installed near maritime safety communications equipment
or other critical navigation or communication equipment operating
between 0.45-30 MHz.
ICES Wording
z
This ISM device complies with Canadian ICES-001 and ICES-003.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.
CANICES-3(B)/NMB-3(B)
Energy Regulation Wording
This AC Adapter (QE-AP105AA) is compliance
with the level V performance requirements under
the International Efficiency Marking Protocol.
Panasonic Products Limited Warranty
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Corporation of North America (referred to as “the
warrantor”) will, for the length of the period indicated on the chart below, which
starts with the date of original purchase (“warranty period”), at its option either
(a) repair your product with new or refurbished parts, (b) replace it with a new or
a refurbished equivalent value product, or (c) refund your purchase price. The
decision to repair, replace or refund will be made by the warrantor.
Product or Part Name
Parts
Labor
Wireless Charging Pad
1 year
Not Applicable
During the “Labor” warranty period there will be no charge for labor. During the
“Parts” warranty period, there will be no charge for parts. This Limited Warranty
excludes both parts and labor for incorporated rechargeable Li-ion batteries and
cosmetic parts (cabinet). This warranty only applies to products purchased and
serviced in the United States or Puerto Rico. This warranty is extended only to the
original purchaser of a new product which was not sold “as is”.
Mail-In Service
--Online
Online Repair Request
To submit a new repair request and for quick repair status visit our Web Site at
www.panasonic.com/repair.
When shipping the unit, carefully pack, include all accessories, and send it prepaid,
adequately insured and preferably in the original carton. When shipping Lithium
Ion batteries please visit our Web Site at www.panasonic.com/BatteryHandling
as Panasonic is committed to providing the most up to date information. Include
a letter detailing the complaint, a return address and provide a daytime phone
number where you can be reached. A valid registered receipt is required under the
Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER
WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE
INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF
PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT
RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Read these safety instructions carefully and completely. Not
doing so can lead to risk of fire, personal injury, electric shock
and property damage.
The cautions are classified as follows.
Important Safety Instructions
Please be sure to read
Failure to follow the following safety instructions can lead to fire,
electrical shock, personal injury or property damage or damage
to this product.
Safety Instructions on the Wireless Charging Pad
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which
are caused by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business
or rental use of the product, or service by anyone other than a Factory Service Center
or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from the servicer,
loss of or damage to media or images, data or other memory or recorded content.
The items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY
OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED
WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the exclusions
may not apply to you.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. If a problem with this product develops during or
after the warranty period, you may contact your dealer or Service Center. If the
problem is not handled to your satisfaction, then write to the warrantor’s Consumer
Affairs Department at the addresses listed for the warrantor.
PARTS AND SERIVCE, WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY, ARE YOUR RESPONSIBILITY.
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate
your nearest Dealer or Service Center; purchase Parts and
Accessories; or make Customer Service and Literature
requests by visiting our Web Site at:
http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Owner’s Manual online for
all Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
npcparts@us.panasonic.com
You may also contact us directly at:
1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic National Parts Center
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, and American
Express.)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
Panasonic Corporation
As of Aug/2013
Any phone or other device carrying the Qi logo will
work with any charging surface that carries the Qi logo,
regardless of manufacturer or brand.
Qi and the Qi logo are the trademarks of the Wireless
Power Consortium (WPC).
Precautions for Use
z
Avoid locations with extremely high temperatures, low temperatures,
or high humidity. Use the product in a location with an ambient
temperature of 41°F (5°C) - 95°F (35°C) and an ambient humidity
of 45% - 85%. If it is determined through an investigation that the
product malfunctioned as a result of use in an environment with an
extreme temperature or high humidity, the malfunction will not be
covered by the warranty and the product will not be repaired.
z
Do not use the product in a location with excessive dust or vibration.
z
Periodically clean the connection terminals and other portions of
this product using a dry cotton swab, and so on. Dirty connection
terminals could cause poor connections. In addition, do not apply
Included Items
Read these safety instructions carefully and completely. Not
and property damage.
Important Safety Instructions
Please be sure to read
Thank you for choosing Panasonic.
Before using the product, be sure to read this “Owner’s manual” and follow
the instructions to use the product correctly.
After reading the owner’s manual, store it in a handy location for future refer-
ence.
In addition, observe all warnings and cautions on the product.
QE-TS101AATR
S1113-0
Owner’s Manual
Wireless Charging Pad
Model No.
QE-TS101AA
Wireless Charging Pad
Any phone or other device carrying the Qi logo will
work with any charging surface that carries the Qi logo,
regardless of manufacturer or brand.
Qi and the Qi logo are the trademarks of the Wireless
Power Consortium (WPC).
Owner’s Manual
Charging
Non-Slip Cushions
AC Adapter
Wireless Charging Pad
a strong force when cleaning the product. Otherwise, the terminals
could be deformed.
z
Discoloration may occur due to the user’s usage conditions or
environment.
z
If the product is dirty, wipe it clean using a soft, dry cloth. Do not
use benzene, paint thinner, alcohol, cleaning agent, or similar
substances. Otherwise, the exterior or characters could be affected.
z
When using the product, keep it as far away as possible from fixed-
line telephones, televisions, radios, and similar devices. Otherwise,
the devices could be adversely affected.
z
If a Qi-compatible device is used to make a telephone call or
communicate while it is being charged by this product, poor
reception could result.
z
This product may become warm during charging, but this is not a
malfunction.
z
Before charging, carefully read the user’s manual of the Qi-
compatible device.
z
Do not place a Qi-compatible device on this product while the
device is connected to a charging adapter (including micro-USB
adapters) or micro-USB cables for computers.
z
Although a Qi-compatible device can be charged while the power
is turned on and the device is in standby mode, the charging time
may be longer.
z
Do not place magnetic cards or similar items near this product. The
magnetic data could be deleted.
z
Do not place magnetized items near this product. Strong
magnetism near the product could cause it to malfunction.
z
The wireless charging pad’s AC adapter is compatible with voltages
from AC 100 V to AC 240 V.
z
However, the plug shape is for a voltage of AC 120 V (UL
standards). When using the product overseas, a plug adapter that
is suitable for the travel destination is required. However, do not
use a voltage converter (travel adapter) for charging.
z
Do not use a device or AC adapter other than the specified devices
with this product.
z
When charging a Qi-compatible device, remove any covers, films,
stickers, and so on, from the device.
z
Place the product on a sturdy, level surface during charging.
z
During charging, do not move this product or the Qi-compatible
device.
If the Qi-compatible device is accidentally moved during charging,
remove the device from the product, wait approximately 15
seconds, and then position the device on the wireless charging pad
in a location where the LED indicators come on in blue.
z
When charging a Qi-compatible device that is equipped with a
vibrating function, turn off the vibrating function. If the Qi-compatible
device vibrates and moves, charging may not be completed or the
device could fall.
z
Multiple Qi-compatible devices cannot be charged at the same
time.
z
When using this product to charge a Qi-compatible device, keep
all other devices that can be charged wirelessly at least 11-4/5
in (30cm) away. Otherwise, the Qi-compatible device may not be
detected correctly and cannot be charged.
z
Do not affix stickers to this product or cover it with a cloth.
Otherwise, the Qi-compatible device may not be detected correctly
and cannot be charged.
LED Indicator