1. DL manuals
  2. Panasonic
  3. All in One Printer
  4. WORKIO DP-C213
  5. Operating Instructions Manual

Panasonic WORKIO DP-C213 Operating Instructions Manual

Manual is about: Digital Color Imaging Systems, instructions for For Facsimile and Internet Fax

Summary of WORKIO DP-C213

  • Page 1

    Before operating this machine, please carefully read this manual and keep this documentation in a safe place for future reference. (illustration shows optional accessories that may not be installed on your machine.) english model no. Dp-c354 / c264 model no. Dp-c323 / c263 / c213 operating instructi...

  • Page 2: Oduct Over

    Pr oduct over vie w 2 operating instructions adobe reader 5.0 or newer is required and must be installed to read the operating instructions. Pjjxc0110zb panasonic communications co., ltd. Digital imaging company 2005 panasonic communications co., ltd. All right reserved. Unauthorized copying and dis...

  • Page 3: Useful Office Functions

    P roduct over vie w 3 useful office functions control panel angle adjustment the control panel viewing angle is adjustable to 4 positions. Pull the release lever to adjust the viewing angle. Normal position sd card slot and pcmcia/pc card slot standard built-in sd card slot and pcmcia/pc card slot a...

  • Page 4: Oduct Over

    Pr oduct over vie w 4 facsimile / internet fax (option) ■ address book (facsimile) ● creating an address book .............................. 52 ■ address book (internet fax) ● creating an address book .............................. 54 ■ placing originals (facsimile/internet fax) ● how to place origi...

  • Page 5

    P roduct over vie w 5 appendix ■ specifications ● main unit ......................................................... 94 ● adf (standard) ............................................... 95 ● pcl printer unit (standard) ............................ 95 ● network scanner (dp-c354/c264: standard, dp-c32...

  • Page 6: Oduct Over

    Pr oduct over vie w 6 warning stop operation immediately if your machine emits smoke, excessive heat, unusual noise or smell, or if water is spilt onto the machine. These conditions can cause fire. Immediately switch off and unplug the machine and contact the authorized panasonic dealer. Do not disc...

  • Page 7: Caution

    P roduct over vie w 7 caution never touch a labelled area. You can get burnt. If a sheet of paper is wrapped around the heat roller, do not try to remove it yourself to avoid injuries or burns. Switch off the machine immediately and contact the authorized panasonic dealer. Do not use conductive pape...

  • Page 8: Oduct Over

    Pr oduct over vie w 8 important safety instructions caution caution consumable safeguards be sure to use the specified type of batteries only. Ensure that batteries are installed with correct polarity. Incorrectly installed batteries can burst or leak, resulting in spillage or injuries. Caution on t...

  • Page 9: Precautions

    P roduct over vie w 9 precautions ■ ■ ■ ■ ■ laser safety laser safety this unit employs a laser. Only qualified service personnel should attempt to service this device due to possible eye injury. Caution: use of controls, adjustments or performance procedures other than those specified herein may re...

  • Page 10: Oduct Over

    Pr oduct over vie w 10 precautions warning for u.K. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13amps and that it is ...

  • Page 11

    P roduct over vie w 11 ■ maximum copies limitation after setting the maximum allowed number of copies for each department, consult with your key operator when the total copy count reaches the designated limit and the message appears on the touch panel display. ■ auto image density/ colour registrati...

  • Page 12: Oduct Over

    Pr oduct over vie w 12 security suggestions for key operators to maintain your machine’s highly-sensitive document data secure from unauthorized users, machine access must be restricted, managed, and controlled from the initial machine installation, network connection, network configuration, and set...

  • Page 13

    P roduct over vie w 13 this symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they w...

  • Page 14: Oduct Over

    Pr oduct over vie w 14 inner output tray 2 1 3 4 outer/inner view adf cover power switch on control panel front cover paper tray 1, 2 paper tray 3, 4 (option) off adf (automatic document feeder) right side cover adu cover option feed cover 2 1 3 4 usb 2.0 port used for local printing lan port used f...

  • Page 15: Control Panel

    P roduct over vie w 15 control panel contents energy saver key saves power while the machine is not in use. Touch panel display sets desired functions. (see pages 17-19) interrupt key interrupts other copy job while making copies. Function key used for changing the initial function values (default v...

  • Page 16: Oduct Over

    Pr oduct over vie w 16 lights ( red ): when the machine stops due to the following condition(s): ● no paper in the selected tray or toner has run out. ● paper has misfed, etc. Lights ( orange ): when the machine alerts of the following condition(s): ● no paper in the tray. (tray is not selected) ● t...

  • Page 17: Touch Panel Display

    P roduct over vie w 17 contents function indication indicates the function mode. (copy, facsimile/internet fax, scan/email or print) message area indicates the message. Status button indicates the problem status. (see page 63) basic menu button returns basic screen from the more menus screen. More m...

  • Page 18: Oduct Over

    Pr oduct over vie w 18 contents function indication indicates the function mode. (copy, facsimile/internet fax, scan/email or print) message area indicates the message. Status button indicates the problem status. (see page 63) address book button returns address book screen from the basic menu scree...

  • Page 19

    P roduct over vie w 19 contents function indication indicates the function mode. (copy, facsimile/internet fax, scan/email, or print) message area indicates the message. Status button indicates the problem status. (see page 63) address book button returns address book screen (default) from the basic...

  • Page 20: Cop

    Cop ying 20 placing originals (copy) ■ ■ ■ ■ ■ how to place originals set the originals up to the upper limit indicator. Original guides adjust the original's width. Upper limit indicator upper guide ● ● ● ● ● on the adf notice for adf original size : a3, b4, fls1(8" x 13"), fls2(8.5" x 13"), a4, a4...

  • Page 21: Caution

    Cop ying 21 a5 a4 a5-r a4-r a3 b4 fls1, fls2 align the original to top left corner mark ( ). ● if the original is not positioned properly, a portion of the original may not be copied. ● for originals smaller than a5 size, position the original within the a5 area and select a5. Original orientation e...

  • Page 22: Cop

    Cop ying 22 full size/auto colour note place original(s) on the adf, or platen glass. 1 press the copy key if the machine is set to other function mode. 2 ● when copying from the adf, read the notice for adf. (see pages 20 and 56) face up up to 70 sheets (80 g/m 2 ) basic copy operation ● during the...

  • Page 23

    Cop ying 23 ● select "yes" to cancel a job. Enter the desired number of copies. (up to 999) 4 select the required settings. (see pages 24-39) 3 press the start key. 5 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note ● origina...

  • Page 24: Cop

    Cop ying 24 basic menu & more menus basic menu when " quality adj. " is selected. When " paper/output tray " is selected. Selects the output tray (inner/outer) ● outer is available when optional finisher/exit tray is installed. Selects the paper tray manually. ● paper tray 3 & 4 are available when o...

  • Page 25

    Cop ying 25 when " proof set " is selected. When " preset jobs " is selected. Makes one proof copy before proceeding a multi-set copy job with various settings. When " output queue " is selected. Up to 10 copy jobs can be stored in memory (m1 to m10) for recall at a later time. Refers to a list of j...

  • Page 26: Cop

    Cop ying 26 basic menu & more menus more menus 1 -> 1 1-sided original to 1-sided copy (default) (see pages 30 and 31) (see pages 32 and 33) (see pages 34 and 35) refer to 2-sided copy mode in the operating instructions (for copier) on the provided cd-rom. 2-sided / original->copy tab 1 -> 2 1-sided...

  • Page 27

    Cop ying 27 refer to zoom mode, effect modes in the operating instructions (for copier) on the provided cd-rom. Refer to insertion modes, overlay modes in the operating instructions (for copier) on the provided cd-rom. Zoom / effects tab zoom auto zoom edge book margin stamping centering image repea...

  • Page 28: Cop

    Cop ying 28 reduction / enlargement copy copying with preset ratios (reduction/enlargement) note ex: enlargement a4-r a3 place original(s) in landscape orientation on the adf or platen glass. (see pages 20 and 21) 1 ● when changing the paper size, select "paper/output tray" and select a paper tray. ...

  • Page 29

    Cop ying 29 enter the desired number of copies. (up to 999) 4 press the start key. 5 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note a3 b4 a4 a5 a3 100 87 71 50 b4 115 100 82 58 a4 141 122 100 71 a5 200 173 141 100 the exact...

  • Page 30: Cop

    Cop ying 30 2-sided copy 1 -> 2 copy : select 1 -> 2 copy mode when copying two 1-sided originals onto one 2-sided copy. The 1st original's image is copied onto the front side and 2nd original's image is copied onto the back side of the copy. Place original(s) on the adf, or platen glass. (see pages...

  • Page 31

    Cop ying 31 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note portrait : portrait orientation denotes a media that is taller than it is wide. Landscape : landscape orientation denotes a media that is wider than it is tall. Sel...

  • Page 32: Cop

    Cop ying 32 1st page imaged 1st page is copied onto the front side and 2nd page is copied onto the back side of the same paper. Face down align with top center 2-sided copy book -> 2 copy select book -> 2 copy mode when copying two facing pages, or a a3 size original on two separate a4 size sheets. ...

  • Page 33

    Cop ying 33 select a book format and the orientation. 5 enter the desired number of copies. (up to 999) 8 press the start key. 9 select the page order and the copy format. 6 select the page order. 1 select the desired copy format. 2 or ● after finishing copying, press the reset key to return the mac...

  • Page 34: Cop

    Cop ying 34 8 7 8 7 1 2 3 4 6 7 8 5 6 4 5 3 1 2 3 1 2 4 3 1 2 4 4 1 4 3 2 a a 6 4 5 3 1 2 6 4 5 3 1 2 a b 8 7 d e c 3 2 1 b c d e a n in 1 copy n in 1 copy select n in 1 copy mode when copying 2, 4 or 8 sheets of originals (printed on 1-side) onto 1 sheet of paper. Place original(s) on the adf, or p...

  • Page 35

    Cop ying 35 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note enter the desired number of copies. (up to 999) 8 press the start key. 9 ● when copying from the platen glass, place the next original and follow the instructions d...

  • Page 36: Cop

    Cop ying 36 sort copy / finishing sort copy / finishing sort shift-sort ● the following finishing modes are available when the optional finisher and punch unit are installed. ● for more details, refer to sort mode in the operating instructions (for copier) on the provided cd-rom. Shift-group staple-...

  • Page 37

    Cop ying 37 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note when optional 1 bin finisher is installed. Select the orientation. Staple enter the desired number of copies. (up to 999) 6 press the start key. 7 select the punch ...

  • Page 38: Cop

    Cop ying 38 def others double exposure note select "preset jobs". 3 4 select double exposure copy mode when copying a 2-sided original that is smaller than a5 in size onto a standard size media (ex: a4 size). One side (front) of the original is copied at the bottom of the page and the other side (ba...

  • Page 39

    Cop ying 39 ● after finishing copying, press the reset key to return the machine to the initial screen of the current active mode. Note enter the desired number of copies. (up to 999) 5 press the start key. 9 select "yes" to finish copying. 10 ● to continue copying other originals, select "no" and p...

  • Page 40: Printing

    Printing printing from sd memory card / pc 40 printing images directly from the sd memory card press the print key if the machine is set to other function mode. 1 ● be sure to use only genuine sd memory card (up to 1gb). ● the image data saved on the sd memory card, or the pcmcia/pc card cannot be p...

  • Page 41

    Printing 41 4 folder ● if there are no photos on the sd memory card, a file list is displayed instead of the thumbnails image. ● if the desired data and the name of the folder are not displayed, keep pressing the button until the desired data and folder appears. For details regarding the folder name...

  • Page 42: Printing

    Printing printing from sd memory card / pc 42 select "individual" or "index print". 6 for individual : go to page 42. For index print : go to page 43. Select the desired paper tray by pressing "paper tray" and/or 2-sided print, and then select "ok". 8 select "ok". (go to step 9) select a paper tray....

  • Page 43

    Printing 43 select "ok". Select the desired paper tray. Select a printing layout. 7 for index print select the desired paper tray and/or 2- sided print, and then select "ok". 8 when "2-sided" is selected, select the bind position. Select "ok". Select the bind position. "long edge" or "short edge". ●...

  • Page 44: Scanning / Email

    Scanning / email 44 face up up to 70 sheets (80 g/m 2 ) place original(s) on the adf, or platen glass. 1 2 attention ● be sure to use only genuine sd memory card (up to 1 gb). ● use only type ii, pcmcia/pc card adapters intended for 3.3 v operating voltage. Refer to your pcmcia/pc card adapter's use...

  • Page 45

    Scanning/ email 45 sd card slot 4 select "address book", and then select the destination for the scanned data. (pc or sd memory card) ● when transferring the data to a sd memory card, select "sd card / hard drive" and select "sd card" for your destination. Push on the slot cover to open it. Label si...

  • Page 46: Scanning / Email

    Scanning / email 46 when “ quality adj. ” is selected. Change the required default settings. When “ file type and name ” is selected. Scanning ● while in scan / email mode, select "basic menu" to configure the following scanner settings. ● for more details, refer to scanner settings in the operating...

  • Page 47

    Scanning/ email 47 when " job build and sadf " is selected. Refer to scanner settings in the operating instructions (for scanner and email) on the provided cd-rom. When " multi-size feed " is selected. Refer to scanner settings in the operating instructions (for scanner and email) on the provided cd...

  • Page 48: Scanning / Email

    Scanning / email 48 press the function key. 1 select "scanner settings". 2 select "21 add new email address". 3 ■ ■ ■ ■ ■ creating an address book note ● for details on how to edit a registered address, refer to adding to the address book in the operating instructions (for scanner and email) on the ...

  • Page 49

    Scanning/ email 49 enter the destination station (pc) name, and then select "ok". 5 enter the destination name. (up to 15 characters) select "ok". Enter the key name for the email address, and then select "ok". 6 enter the key name. (up to 15 characters) select "ok". Select whether you wish to add t...

  • Page 50: Scanning / Email

    Scanning / email 50 sending email note place original(s) on the adf, or platen glass. 1 2 ● jpeg form data is different from pdf or tiff form, as one file is only for one page. In case of sending plural documents, one file does not go to plural pages and files of plural pages are attached. ● jpeg (j...

  • Page 51

    Scanning/ email 51 4 select "email", and then enter the email address or select an email address from the address book. 3 select "email". Press the start key. 5 ● when scanning from the platen glass, place the next original and follow the instructions described on the touch panel display. Address bo...

  • Page 52: Acsimile / Internet F

    F acsimile / internet f ax (option) 52 ■ ■ ■ ■ ■ creating an address book press the function key. 1 select "fax/email settings". 2 select "00 address book". 3 ● for details on how to edit a registered address, refer to address book in the operating instructions (for facsimile and internet fax) on th...

  • Page 53

    F acsimile/ internet f a x (option) 53 enter the key name for the address book, and then select "ok". 7 enter the key name. (up to 15 characters) select "ok". Enter the name of the destination, and then select "ok". 6 enter the destination name (up to 15 characters) select "ok". Enter the fax number...

  • Page 54: Acsimile / Internet F

    F acsimile / internet f ax (option) 54 ■ ■ ■ ■ ■ creating an address book note press the function key. 1 select "fax/email settings". 2 select "00 address book". 3 ● for details on how to edit a registered address, refer to address book in the operating instructions (for facsimile and internet fax) ...

  • Page 55

    F acsimile/ internet f a x (option) 55 enter the email address, and then select "ok". 5 select whether you wish to add this email address to favourites. 9 to enter other email addresses: repeat steps 5 to 9 or to exit this setting mode: press the reset key. 10 enter the email address. (up to 60 char...

  • Page 56: Acsimile / Internet F

    F acsimile / internet f ax (option) 56 set the originals up to the upper limit indicator. Original guides adjust the original's width. Upper guide upper limit indicator ● when scanning from the adf, read the notice for adf. (see pages 20 and 56) placing originals (facsimile/internet fax) ● ● ● ● ● o...

  • Page 57

    F acsimile/ internet f a x (option) 57 ● ● ● ● ● original size from the adf maximum size minimum size 2000 mm scanning direction 297 mm 140 mm scanning direction 148 mm from the platen glass maximum size 420 mm 297 mm when the popup screen is displayed while setting the address and/or facsimile mode...

  • Page 58: Acsimile / Internet F

    F acsimile / internet f ax (option) 58 sending scanned data via facsimile note ● when scanning full-colour originals, select text/photo, or photo to add more details to the scanned data. However, the scanned data is sent in black and white (grey scale). ● when selecting the destination from the addr...

  • Page 59

    F acsimile/ internet f a x (option) 59 5 enter the fax number. For manual dialing enter the fax number, and then select "ok". 4 select "address book". For address book dialing select the destination station(s) ● the address book is available only when it contains registered destinations. (see pages ...

  • Page 60: Acsimile / Internet F

    F acsimile / internet f ax (option) 60 sending scanned data via internet fax note ● when scanning full-colour originals, select text/photo or photo to add more detail to the scanned data. However, the scanned data is sent in black and white (grey scale). ● when selecting the destination from the add...

  • Page 61

    F acsimile/ internet f a x (option) 61 ● the address book is available only when it contains registered destinations. (see pages 54 and 55) press the start key. 5 ● when sending from the platen glass, place the next original and follow the instructions described on the touch panel display. 4 select ...

  • Page 62: Lem Solving

    Pr ob lem solving 62 troubleshooting check action unit does not operate check if the power switches (main power switch on the rear and power switch on the left side of the machine) are turned on and if the power cord is plugged into the ac outlet. Does the display dark? Press energy saver key on the...

  • Page 63

    P rob lem solving 63 check action marked copies clean the white reference sheet, platen sheet, scanning glass (small), or platen glass (large). (refer to "machine care" below:) is the white reference sheet, platen sheet, scanning glass (small), or platen glass (large) dirty? (1) clean the lsu apertu...

  • Page 64: Lem Solving

    Pr ob lem solving 64 ● when a user error occurs, the location and the procedures for handling the user error are displayed frame by frame on the touch panel display. Check the location, and handle the user error according to displayed pictures, and this manual. (see pages 78-83) ex: front cover is o...

  • Page 65

    P rob lem solving 65 code check points j19 paper feed section & adu section (see pages 66, 67, 69, and 70) j82, j83, adu section & fuser/exit section j88 (see pages 67, and 68) j30, j31, paper feed section & fuser/exit section j38, j39, (see pages 66, 68, 69, and 70) j40, j42-j45 j41, j50, fuser/exi...

  • Page 66: Lem Solving

    Pr ob lem solving 66 ■ ■ ■ ■ ■ paper feed section (paper tray 1) open the feed cover 1. 1 remove the misfed paper. 2 removing misfed paper pull out the paper tray 1. 3 remove the misfed paper. 4 insert the paper tray 1. 5 close the feed cover 1. 6 misfed paper close the sheet bypass. 7 sheet bypass ...

  • Page 67

    P rob lem solving 67 ■ ■ ■ ■ ■ adu section remove the misfed paper. 3 close the adu cover. 4 close the sheet bypass. 5 open the sheet bypass. 1 open the adu cover. 2 sheet bypass sheet bypass adu cover misfed paper adu cover 007basic_op(uk)066_075.Pmd 16/11/2006, 13:08 67.

  • Page 68: Lem Solving

    Pr ob lem solving 68 feed cover 1 ■ ■ ■ ■ ■ fuser/exit section open the right side cover. 2 open the feed cover 1. 1 turn the paper transport knob counterclockwise. 3 removing misfed paper close the right side cover. 4 remove the misfed paper. 5 close the feed cover 1, and sheet bypass. 6 feed cover...

  • Page 69

    P rob lem solving 69 open the transport cover. Remove the misfed paper. Transport cover misfed paper 2 1 ■ ■ ■ ■ ■ paper transport section close the transport cover. 3 transport cover open the feed cover 2, and then remove the misfed paper. Pull out the paper tray 2. 2 1 ■ ■ ■ ■ ■ paper feed section...

  • Page 70: Lem Solving

    Pr ob lem solving 70 open the option feed cover. 1 remove the misfed paper. 2 pull out the paper tray 3 or 4. 3 remove the misfed paper. 4 insert the paper tray 3 or 4. 5 close the option feed cover. 6 ■ ■ ■ ■ ■ paper feed section (optional paper tray 3 or 4) removing misfed paper misfed paper misfe...

  • Page 71

    P rob lem solving 71 ■ ■ ■ ■ ■ 1-bin finisher section slide the finisher to the left. 1 remove the misfed paper. 2 slide the finisher back until it locks into place. 3 open the finisher top cover, and then remove the misfed paper. 4 release button ● push the release button to free the finisher from ...

  • Page 72: Lem Solving

    Pr ob lem solving 72 slide the finisher to the left. 1 remove the misfed paper. 3 open the staple cover. 5 turn the paper transport knob clockwise. 6 ■ ■ ■ ■ ■ 1-bin saddle-stitch finisher section removing misfed paper open the finisher top cover. 2 close the finisher top cover. 4 release button mis...

  • Page 73

    P rob lem solving 73 remove the misfed paper. 7 open the inner cover. 9 remove the misfed paper. 10 slide the finisher back until it locks into place. 12 close the staple cover. 8 misfed paper staple cover close the inner cover. 11 misfed paper inner cover inner cover 007basic_op(uk)066_075.Pmd 16/1...

  • Page 74: Lem Solving

    Pr ob lem solving 74 open the adf cover, and then remove the misfed paper. 1 lift the adf tray. 3 open the exit unit, and then remove the misfed paper. 5 close the exit unit. 6 ■ ■ ■ ■ ■ adf section removing misfed paper open the inner cover, and then remove the misfed paper. 2 remove the misfed pap...

  • Page 75

    P rob lem solving 75 open the adf. 8 9 10 close the adf cover. Adf cover pull down the adf tray, and then close the inner cover. 7 adf tray remove the misfed paper, and then close the adf. Misfed paper 007basic_op(uk)066_075.Pmd 16/11/2006, 13:08 75.

  • Page 76: Replacing Consumab

    Replacing consumab les 76 attention open the paper tray. 1 fan and align the paper together, and then load paper with printing side facing up. 2 close the paper tray. 3 ● if you wish to change the preset paper size used in the paper tray, contact your authorized panasonic dealer. ● do not place the ...

  • Page 77

    Replacing consumab les 77 attention sheet bypass capacity ● capacity : 50 sheets (a4, 80 g/m 2 ) ● weight : 55-220 g/m 2 ● size : a3-a5 ● suitable media : plain paper, thin paper, glossy paper, recycled paper, thick paper, coated paper, index/cover paper, coated/cover paper, transparency, or labels....

  • Page 78: Replacing Consumab

    Replacing consumab les 78 attention open the front cover. 1 gently turn the toner cartridge of the colour displayed on the touch panel display counterclockwise to the unlock mark. 2 pull out the used toner cartridge. 3 ● be sure to use only genuine panasonic colour toner designed for this machine. ●...

  • Page 79

    Replacing consumab les 79 turn the new toner cartridge clockwise gently until it stops. 7 firmly close the front cover. 8 insert the new toner cartridge as far as possible with the arrow label pointing to the unlock mark. 6 new toner cartridge new toner cartridge front cover gently peel the tape off...

  • Page 80: Replacing Consumab

    Replacing consumab les 80 open the front cover. Front cover ● make sure that the machine has stopped printing before opening the front cover. Attention 1 remove the toner waste container. 2 unlock the opc drum unit by turning the drum release knob counterclockwise. 4 ● replace the opc drum unit of t...

  • Page 81

    Replacing consumab les 81 8 10 do not remove the drum protective cover until step 8. Gently close the front cover. Place the old opc drum unit inside the plastic bag, and dispose of it according to your local regulations. 12 lock the new opc drum unit by turning the drum release knob clockwise. Past...

  • Page 82: Replacing Consumab

    Replacing consumab les 82 attention 1 ● do not reuse toner from the toner waste container. ● do not use the cleaner if it is dirty. ● when the toner adheres to the machine, wipe it off with a cloth. Replacing toner waste container / cleaning the lsu aperture glass open the front cover. Front cover t...

  • Page 83

    Replacing consumab les 83 remove the cleaner from the inside of the front cover. 6 insert the new toner waste container into the machine until it stops. 9 clean the lsu aperture glass (4 slots). 7 gently close the front cover. 10 insert the cleaner back inside the front cover. 8 toner waste containe...

  • Page 84: Replacing Consumab

    Replacing consumab les 84 replacing staples note open the stapler cover. 1 pull out the staple cartridge. 2 ● when the staple jams, an error message will be displayed. Remove the jammed staple from the staple cartridge as illustrated. Replacing staples (fq-ss32) staple cartridge (fq-ss32) stapler co...

  • Page 85

    Replacing consumab les 85 replace the staple case with a new one. 3 staple case (new) insert the staple cartridge. 4 select "more menus". 7 close the stapler cover. 5 select "sort / finish", "staple-sort", and the staple position. (see pages 36 and 37) 8 staple cartridge to check the stapling operat...

  • Page 86: Replacing Consumab

    Replacing consumab les 86 replacing staples note 1 2 ● when the staple jams, an error message will be displayed. Remove the jammed staple from the staple cartridge as illustrated. Replacing staples (dq-ss35) staple cartridge (dq-ss35) open the staple cover. Turn the knob on the stapler unit clockwis...

  • Page 87

    Replacing consumab les 87 continue on the next page... Pull out the stapler unit. 3 stapler unit set the staple case (new). 6 pull out the staple cartridge by pinching the green buttons. 4 remove the tape. 7 remove the staple case (empty). 5 insert the staple cartridge. 8 ● push on each side of the ...

  • Page 88: Replacing Consumab

    Replacing consumab les 88 insert the stapler unit. 9 to check the stapling operation, place originals on the adf and select "more menus". 11 close the staple cover. 10 select "sort / finish", "staple-sort", and the staple position. (see pages 36 and 37) 12 press the start key. 13 face up up to 70 sh...

  • Page 89

    Replacing consumab les 89 memo: 008basic_op(uk)076_089.Pmd 16/11/2006, 13:10 89.

  • Page 90: Replacing Consumab

    Replacing consumab les 90 dispose of the punch hole residue (1-bin saddle-stitch finisher) slide the finisher to the left. 1 pull out the punch hole residue container (full). 2 empty out the punch hole residue container. 3 dispose of the punch hole residue insert the punch hole residue container (em...

  • Page 91

    Replacing consumab les 91 memo: 009basic_op(uk)090_093.Pmd 16/11/2006, 13:10 91.

  • Page 92: Replacing Consumab

    Replacing consumab les 92 replacing the battery caution ! Remove the screw with a screwdriver. 1 pull out the battery holder. 2 ● this product contains a lithium battery. Replace only with the same or equivalent type. Improper use or replacement may cause overheating, rupture or explosion resulting ...

  • Page 93

    Replacing consumab les 93 remove the old battery. 4 insert the new battery into the holder. 5 turn the battery holder upside down, and then insert it into the machine. 6 fasten it with the screw. 7 new battery battery holder screw ● “+” side of battery should be facing upwards. ● replace only with t...

  • Page 94: Appendix

    Appendix 94 type: semi console type platen type: fixed acceptable originals: sheets, books (max. A3) copying method: laser indirect electrostatic fusing method: induction heating system imaging method: dry-type dual component trickle resolution: max. 600 dpi operation panel: 7.8" full colour touch p...

  • Page 95

    Appendix 95 tray capacity: 70 sheets (80 g/m 2 ) original size: a3, b4, a4, a4-r, a5, a5-r, fls1, fls2 paper weight: 1 sided : 50-105 g/m 2 2 sided : 64-105 g/m 2 electrical requirements: supplied from the machine paper size: a3, b4, a4, a4-r, a5-r, fls1, fls2 paper weight: 64-105 g/m 2 paper capaci...

  • Page 96: Appendix

    Appendix 96 compatibility: itu-t group 3 coding scheme: jbig, mh, mr, mmr (conforms to itu-t recommendations) modem type: itu-t v.34, v.17, v.29, v.27 ter, and v.21 modem speed: 33600-2400 bps document size: a5 - a3 max : platen glass : a3 adf : a3 min : platen glass : no minimum adf : a5 scanning m...

  • Page 97

    Appendix 97 mode bin non-sort, sort, staple tray saddle-stitch paper size: bin a3, b4, a4, a4-r, a5-r, fls1, fls2 tray a3, b4, a4-r paper weight non-sort mode : 64-220 g/m 2 paper capacity bin maximum (1-sided copy) : 1000 sheets (a5, a4) 500 sheets (b4, fls1, fls2, a3) 30 set (stapling mode) ● to a...

  • Page 98: Appendix

    Appendix 98 specifications paper type ● commercial papers described below are acceptable, however, the standard paper (igepa, etc) is recommended for optimum copy quality and performance of the machine. Paper type paper weight tray 1 - 4 sheet bypass 2-sided copy/print thin 55-63 g/m 2 not compatibl...

  • Page 99: Option and Supplies

    Appendix 99 option and supplies part name part no. Remarks system console 1 da-ds320 3rd paper tray (550 sheets x 1) system console 2 da-ds321 3rd and 4th paper trays (550 sheets x 2) 1 bin saddle-stitch finisher da-fs356 optional paper transport unit is required. 1 bin finisher da-fs350 optional pa...

  • Page 100: Appendix

    Appendix 100 declaration of conformity (doc) panasonic communications co., ltd. Declares that this g3 facsimile equipment is in compliance with the essential requirements and other relevant provisions of directive 1999/5/ec. If you want to get a copy of the original declaration of conformity of our ...

  • Page 101

    Appendix 101 machine noise information ordinance 3. Gsgv, january 18, 1991: the maximum sound pressure level is equal or less than 70 db(a) according to iso 7779. The grant of a telepermit for any item of terminal equipment indicates only that telecom has accepted that the item complies with the min...

  • Page 102: Appendix

    Appendix 102 index numerics 1 -> 2 copy ............................................................ 26, 30 2 -> 1 copy .................................................................. 26 2 -> 2 copy ............................................................ 26, 30 2 page copy .....................

  • Page 103

    Appendix 103 j jam error codes (j codes) ......................................... 65 job build and sadf (copy) ......................................... 26 job build and sadf (scan/email) ............................... 47 jpeg ................................................................ 40, 46...

  • Page 104: Appendix

    Appendix 104 index resolution (scanning) ................................................. 46 right side cover .......................................................... 14 rotate-group ......................................................... 27, 36 rotate-sort ........................................

  • Page 105: Glossary

    Appendix 105 glossary address book address book dialing adf (automatic document feeder) cd-rom dds (document distribution system) density dept. Code (department code) dhcp disk drive dpi drum fax board ftp g3 (group 3) the address book is a convenient directory that stores contact phone numbers and ...

  • Page 106: Appendix

    Appendix 106 glossary hdd (hard disk drive) install internet internet fax jpeg key name keypad lan (local area network) lcd memory modem module network pc pcmcia/pc card pcl (printer control language) pdf the physical component of a pc which performs the basic operations on the hard disk-including r...

  • Page 107

    Appendix 107 protocol resolution sd card (secure digital memory card) sleep mode smtp (simple mail transfer protocol) software station name tcp/ip thumbnails tiff toner verification stamp a standard process, a set of rules & conditions that perform a particular function. A word which is very common ...

  • Page 108

    Memo 011basic_op(uk)108_111.Pmd 16/11/2006, 13:10 108.

  • Page 109

    Memo 011basic_op(uk)108_111.Pmd 16/11/2006, 13:10 109.

  • Page 110

    Memo 011basic_op(uk)108_111.Pmd 16/11/2006, 13:10 110

  • Page 111

    The following trademarks and registered trademarks are used throughout this manual: microsoft, windows, windows nt, windows server, outlook & windows logo are registered trademarks of microsoft corporation in the usa and other countries. Microsoft product screen shot(s) reprinted with permission fro...

  • Page 112

    C0606-3116(01) pjqmc0580zd november 2006 p ublished in japan for service, call: for customer support: panasonic communications co., ltd. Fukuoka, japan http://panasonic.Net © 2006 panasonic communications co., ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. The...