1. DL manuals
  2. PlaySafe
  3. Swing Set
  4. Bristol Swing Set
  5. Owner's Manual And Assembly Instruction

PlaySafe Bristol Swing Set Owner's Manual And Assembly Instruction

Manual is about: 22-PS150

Summary of Bristol Swing Set

  • Page 1

    1 ©2006 pacific cycle, inc. Owner’s manual and assembly instruction model #: 22-ps150 model name: bristol swing set manual date: september, 2008 important: keep this owner’s manual; do not discard in case you need to contact pacific cycle, inc. In the future. Should there be a change of ownership, p...

  • Page 2

    2 ©2006 pacific cycle, inc. To make claim under warranty, notification of such defect must be given to pacific cycle, inc. By calling the phone number below, you will be instructed on how the product or part needing replacement should be shipped postpaid to pacific cycle, inc. Customer service and a...

  • Page 3

    3 ©2006 pacific cycle, inc. Warnings and safety information o bserve all warnings and statements in order to reduce the risk of injury or death . Before you assemble the swing set , find level ground not less than 6 feet from any structure or obstruction to the swing set . Y our swing set must have ...

  • Page 4

    4 ©2006 pacific cycle, inc. Proper use this swing set is designed for use by children ages 3 to 10 under adult supervision. The maximum number of users this unit is intended for is 8 children with a maximum weight of 105 lbs each. The maximum fall height for this swing set is 74”. Single ride (i.E. ...

  • Page 5

    5 ©2006 pacific cycle, inc. Checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability of material in your area and its cost. (the information above h...

  • Page 6

    6 ©2006 pacific cycle, inc. Pre-assembled hardware for easier assembly, playsafe™ has pre-assembled some of the parts for you. Most of the screws and bolts should already be in place. If removal of this hardware is required for certain assembly steps, it should be replaced in its original position. ...

  • Page 7

    7 ©2006 pacific cycle, inc. 4 remove the hardware from the middle section of a leg. Match up the holes of the mid-leg and support bar and re-insert the hardware through both. Repeat the process for the opposite side and center legs. It may be necessary to pull both legs towards each other in order f...

  • Page 8

    8 ©2006 pacific cycle, inc. 2 attach the two vertical poles to the glider attachment. Start by removing the hardware from the lower section of the glider attachment. Align the vertical bar with the glider attachment and re-insert the hardware. Repeat the process for the other side. Note: the curved ...

  • Page 9

    9 ©2006 pacific cycle, inc. Swing and trapeze assembly pre-assembled parts • swing seats should be attached to the chain. Step illustration instructions hardware reference 1 before attaching the swings, you will need to verify the hook positioning. Although the hooks will be pre-assembled in the top...

  • Page 10

    10 ©2006 pacific cycle, inc. See-saw assembly required parts: see-saw frame and extension frame attachment top tube attachment seat x2 step illustration instructions hardware reference 1 remove the hardware from the see-saw frame and connect the extension. Re- insert the hardware and tighten. Note: ...

  • Page 11

    11 ©2006 pacific cycle, inc. 6 once fully assembled, check that the see- saw hinges freely. If it does not, make sure that the bolts on the see-saw top tube are not overly tightened. Part ref. #: pshw10 slide assembly proper placement: slide assembly correct location incorrect location pre-assembled...

  • Page 12

    12 ©2006 pacific cycle, inc. 4 locate the slide front legs and insert them into the front hand rail tubes, on the underside of the slide. Align the holes and secure with the screws, washers and lock nuts. Part ref. #: pshw24 5 slide the two ladder steps onto the legs of the slide. Align the holes an...