1. DL manuals
  2. PlumbNation
  3. Thermostat
  4. JG PRT-E
  5. Operating Instructions Manual

PlumbNation JG PRT-E Operating Instructions Manual

Summary of JG PRT-E

  • Page 1

    Operating instructions model: jg stat/v3 this is a multi mode thermostat, please see page 13 for setup instructions revision 1 - 10/09 ref: jgstat/v3.

  • Page 2: Plumbnation.Co.Uk

    The nation’s favourite for plumbing & heating supplies secure payments shop online with confidence free shipping on all orders over £100 to mainland uk finance available spread the cost with low interest rates price match always get the best deals available boilers radiators heating controls pipes &...

  • Page 3

    This is inside front cover and will be blank.

  • Page 4: Contents Page

    1 contents page what is a programmable thermostat? 2-4 installation 5-6 icons explained 6 temperature display 7 setting the clock 7 setting the comfort levels 8-9 keypad lock facility 9 temperature hold 10 setting the temperature 10 holiday feature 11 turning the heating on/off 12 factory reset 12 s...

  • Page 5

    2 what is a programmable room thermostat? A programmable room thermostat is both a programmer and a room thermostat. A programmer allows you to set “on” and “off” periods to suit your own lifestyle. A room thermostat works by sensing the air temperature, switching on the heating when the air tempera...

  • Page 6

    3 down. Turning a programmable room thermostat to a lower setting will result in the room being controlled at a lower temperature, and saves energy. The way to set and use your programmable room thermostat is to ind the lowest temperature settings that you are comfortable with at the different times...

  • Page 7

    4 (trvs) on individual radiators. If you don’t have trvs, you should choose a temperature that is reasonable for the whole house. If you do have trvs, you can choose a slightly higher setting to make sure that even the coldest room is comfortable, then prevent any overheating in other rooms by adjus...

  • Page 8: Installation Procedure

    5 installation procedure do’s 1. Do mount the thermostat at eye level. 2. Do read the instructions fully so that you can get the best from our product. Don’ts 1. Do not install near a direct heat source as this will affect the workings of the thermostat. 2. Do not push hard on the lcd otherwise you ...

  • Page 9: Icons Explained

    6 step 2 place the thermostat front somewhere safe. Terminate the thermostat as shown in the diagrams at the back of this booklet. Step 3 clip the front of the thermostat to the back plate. Icons explained symbol description heat on icon shown when the heating is on flashing when the optimum starts ...

  • Page 10: Temperature Display

    7 temperature display room temp = this is the current room temperature. Set = this is the temperature you are trying to achieve in your home. Setting the clock to set the clock, follow the steps below: • with the thermostat turned on, press the clock button twice. • you are now able to set the minut...

  • Page 11: Comfort Levels Explained

    8 comfort levels explained the stat/v3 provides weekday/weekend or 7 day programming. You should consult the “coniguration menu” section to select the required mode. The thermostat is supplied with comfort levels already programmed, but these can be changed easily. The default times are: 08.00 - 21°...

  • Page 12: Locking The Thermostat

    9 • press h. • using the up/down arrow keys, enter the required wake temperature. • press h. • you will now see “leave”. • you should repeat the programming for each period, entering --.—for unused periods. Note: for weekday/weekend programming, the 4 comfort levels are the same for all weekdays. Fo...

  • Page 13: Temperature Hold

    10 temperature hold the temperature hold function is ideal for parties or when you will be going out for a number of hours. It allows you to hold a temperature for a desired period. • press h. • using the up/down arrow keys enter the required hold time. • press h. • using the up/down arrow keys ente...

  • Page 14: Holiday

    11 holiday the stat/v3 has a holiday function. This allows you to enter a holiday setting. During a holiday, the thermostat will maintain the frost set temperature. At the end of your holiday, the thermostat will revert back to the programmed setting ensuring that your home is warm on your arrival. ...

  • Page 15: Heat On / Off

    12 heat on / off frost protect mode: pressing the power button once will place the thermostat in frost protect mode. In this mode, the thermostat will display the frost icon and will only turn the heating on should the room temperature drop below the set temperature (see page 14) should the heating ...

  • Page 16: Setting The Mode

    Setting the mode the stat/v3 has 4 modes, these are explained below: mode no. Mode explanation 00 non programmable mode with built in air sensor 01 non programmable with remote sensor options 02 programmable mode with built in air sensor 03 programmable mode with remote sensor options first select t...

  • Page 17: Optional Features Explained

    14 the following settings are optional and in most cases need not be adjusted optional features explained feature 01 - temperature format: this function allows you to select between °c and °f. Feature 02 – switching differential: this function allows you to increase the switching differential of the...

  • Page 18

    15 feature 04 – frost protect temperature: this is the temperature maintained when the thermostat is in frost mode. The range is 07 - 17°c. The default is 12°c and is suitable for almost all applications. Feature 05 – output delay: to prevent rapid switching, an output delay can be entered. This can...

  • Page 19

    16 • 00 = built in air sensor • 01 = remote air sensor • 02 = floor sensor only • 03 = floor sensors & built in air sensor • 04 = floor sensor and remote air sensor feature 09 – floor limit: when the thermostat is operating in mode 01 and 03 (as described on page 13) and function 08 is set to 02, 03...

  • Page 20

    17 feature 12 – weekday/weekend or 7 day programming: the thermostat offers two programming methods. Weekday/ weekend allows you to program 4 comfort levels for the weekday and 4 different comfort levels for the weekend. In 7 day program mode, each day has 4 comfort levels that can be programmed ind...

  • Page 21: Feature Table

    Adjusting the optional settings 1. To access the coniguration menu, turn off the thermostat by pressing and holding down the power button. Then, press and hold the clock button until the display lights up. 2. The small number is the feature number, the large number is the setting value. 3. Use the c...

  • Page 22: Feature Table

    Feature table (continued) feature description setting 04 frost temperature 07-17°c (12°c default) 05 output delay 00-15 minutes (00 default) 06 communication id set unique comms address 01-32 07 up/down temp limit 00-10°c (00°c default) 08 sensor selection 00 = built in air sensor 01 = remote air se...

  • Page 23: Feature Table

    20 feature table (continued) feature description setting 09 floor limiting sensor 20-45°c 28°c default 10 optimum start 00-03 (00 hours default) 11 rate of change information only 12 mode select 00=weekday/weekend 01 = 7 day programming.

  • Page 24

    21 jg stat/v3.

  • Page 25

    Support tel: 01254 870303.