1. DL manuals
  2. Poise Technology
  3. Network Accessory
  4. AG-188
  5. User Manual

Poise Technology AG-188 User Manual

Summary of AG-188

  • Page 1

    Ag-188 user manual 1 / 53 ag-188 user manual.

  • Page 2

    Ag-188 user manual 2 / 53 1 ag-188 features ..................................................................................................3 1.1 appearance .................................................................................................................3 1.2 interface ...............

  • Page 3

    Ag-188 user manual 3 / 53 6 network diagnosis ...............................................................................................3 7 restore to factory default ....................................................................................3 8 post mode(safe mode) ......................

  • Page 4

    Ag-188 user manual 4 / 53 1 ag-188 features 1.1 appearance power: power indicator. Server: server indicator. Registered: on; registering: blinking; do not register: off. Voip: indicate the calling status. Hook-on: off; hook-off and in voip state: on; hook-off and in pstn state: off 1.2 interface pow...

  • Page 5

    Ag-188 user manual 5 / 53 z the network connects:2 rj45 connect, a wan, a lan 1.4 software z support two sip servers running at the same time. Z back-up sip server support. Z nat, firewall. Z dhcp client and server. Z support pppoe, (used for adsl, cable modem connecting). Z support major g7.Xxx cod...

  • Page 6

    Ag-188 user manual 6 / 53 1.6 compliant standards ● ce: en55022, en55044 ● fcc part 15 ● rohs 1.7 operating requirement ● operation temperature: 0 to 40° c (32° to 104° f) ● storage temperature: -30° to 65° c (-22° to 149° f) ● humidity: 10 to 90% no dew 1.8 package z size 128 x 85 x 30 mm z packing...

  • Page 7

    Ag-188 user manual 7 / 53 1.9 installation use ethernet cable to connect ag-188’s lan port and your computer. Set your computer’s ip to the network 192.168.10.X or using dynamic obtain ip. Open your web browser and key in 192.168.10.1. Then you will see the logon page of ag-188, the default username...

  • Page 8

    Ag-188 user manual 8 / 53 2 web configuration 1.1 access web setting page enter ag-188 ip address in the web browser and press enter to go to the log on page, and key in the username and password to access ag-188 setting page. Default username and password is: administrator: username: admin password...

  • Page 9

    Ag-188 user manual 9 / 53 1.2 current state this page shows ag-188’s running state. Network ：shows the wan and lan port connecting state and current settings. Voip： show the default protocol, the working state of sip and iax2, you can see whether ag-188 has registered the public sip server and iax2 ...

  • Page 10

    Ag-188 user manual 10 / 53 1.3 network 1.3.1 wan config wan port network setting page. Support static ip, dynamic obtain ip and pppoe. Configure static ip: ----enable static; ----set ag-188’s ip address in the ip address; ----set net mask in the net mask field; ----set router ip address in the gatew...

  • Page 11

    Ag-188 user manual 11 / 53 lan config bridge mode: enable this option to switch to bridge mode. Gateway won’t assign ip for its lan port in bridge mode and its lan and wan port will be in the same network. (this setting won’t take effect unless you save the config and reboot the device) ip netmask: ...

  • Page 12

    Ag-188 user manual 12 / 53 1.4 voip 2.4.1 sip config setting page of public sip server: register server addr: register address of public sip server register server port: register port of public sip server register username: username of your sip account (always the same as the phone number) register ...

  • Page 13

    Ag-188 user manual 13 / 53 server. Detect interval time: co-work with the auto detect server, if auto detect server is enable, ag-188 will periodically detect if the sip server is available according this setting. Rfc protocol edition: current ag-188 sip versions. Set to rfc 2543 if the gate need to...

  • Page 14

    Ag-188 user manual 14 / 53 local port: signal port of local, default port is 4569 phone number: phone number of your iax account voice mail number: if the iax support voice mail, but your username of the voice mail is letters which you can not input with the ata , then you use the number to stand fo...

  • Page 15

    Ag-188 user manual 15 / 53 1.5 advance 1.5.1 dhcp server dhcp server manage page. User may trace and modify dhcp server information in this page. Dns relay: enable dns relay function. User may use below setting to add a new lease table. Lease table name: lease table name. Lease time: dhcp server lea...

  • Page 16

    Ag-188 user manual 16 / 53 1.5.2 nat advance nat setting. Maximum 10 items for tcp and udp port mapping. Ipsec alg: enable/disable ipsec alg; ftp alg: enable/disable ftp alg; pptp alg: enable/disable pptp alg; transfer type: transfer type using port mapping. Inside ip: lan device ip for port mapping...

  • Page 17

    Ag-188 user manual 17 / 53 1.5.3 net service http port: configure http transfer port, default is 80.User may change this port to enhance system’s security. When this port is changed, please use http://xxx.Xxx.Xxx.Xxx:xxxx/ to reconnect. Telnet port: configure telnet transfer port, default is 23. Rtp...

  • Page 18

    Ag-188 user manual 18 / 53 1.5.4 firewall settings firewall setting page. User may set up firewall to prevent unauthorized internet users from accessing private networks connected to the internet (input rule), or prevent unauthorized private network devices to access the internet. Access list suppor...

  • Page 19

    Ag-188 user manual 19 / 53 des mask: destination address mask. Indicate the source is dedicate ip if set to 255.255.255.255. Otherwise is network id.

  • Page 20

    Ag-188 user manual 20 / 53 1.5.5 qos settings at-530 ip phone implement qos based on 802.1p, the qos is used to mark the network communication priority in the data link/mac sub-layer. At-530 will sorted the packets using the qos and sends it to the destination. Vlan enable: if enable the vlan servic...

  • Page 21

    Ag-188 user manual 21 / 53 ag-188 gateway implement qos based on 802.1p, the qos is used to mark the network communication priority in the data link/mac sub-layer. Ag-188 will sorted the packets using the qos and sends it to the destination. Qos enable: enable qos service. Qos table include: enable ...

  • Page 22

    Ag-188 user manual 22 / 53 1.5.6 advance sip settings this page is used to set the private sip server, stun server, and back up sip server information. Stun server setting: stun server addr: configure stun server address; stun server port: configure stun server port default 3478 stun effect time: st...

  • Page 23

    Ag-188 user manual 23 / 53 1.5.7 digital map digit map is a set of rules to determine when the user has finished dialing. Ag-188 support below digital map: digital map is based on some rules to judge when user end their dialing and send the number to the server. Ag-188 support following digital map:...

  • Page 24

    Ag-188 user manual 24 / 53 1.5.8 call service settings user configure the value add service such as hotline, call forward, call transfer, 3-way conference call .Etc in this page hotline: configure hotline number. Ag-188 immediately dials this number after hook-off if it is set. Call forward: please ...

  • Page 25

    Ag-188 user manual 25 / 53 black list: incoming call in these phone numbers will be refused. Limit list: outgoing calls with these phone numbers will be refused.

  • Page 26

    Ag-188 user manual 26 / 53 1.5.9 mmi filter mmi filter is used to make access limit to ag-188 gateway. When mmi filter is enable. Only ip address within the start ip and end ip can access ag-188 gateway..

  • Page 27

    Ag-188 user manual 27 / 53 1.5.10 audio settings codec: select the prefer codec; support ulaw, alaw and g729 signal standard: support china, japan and usa standard input volume: handset in volume. Output volume: handset out volume. G729 payload length: g729 payload length vad: enable/disable voice a...

  • Page 28

    Ag-188 user manual 28 / 53 1.6 dial-peer settings please refer to “how to use dial rule?” for detail..

  • Page 29

    Ag-188 user manual 29 / 53 1.7 config manage save config: save current settings. Clear config: restore to default settings. Notice: clear config in admin mode, all settings restores to factory default; clear config in guest modem, all settings except sip, advance sip restore to factory default..

  • Page 30

    Ag-188 user manual 30 / 53 1.8 update web update: update gateway’s settings or firmware. Firmware file is .Dlf extension when configure file is .Cfg extension, ag-188 will auto select configure update or firmware update according the extension. Ftp update: back up the configure file to ftp or tftp s...

  • Page 31

    Ag-188 user manual 31 / 53 gateway original version is: >version:1.0000 conffile version：6 user may edit the configure file version to: >version:1.0007 conffile version：7.

  • Page 32

    Ag-188 user manual 32 / 53 1.9 system manage 1.9.1 account manage set web access account or keypad password of at-530. 1.9.2 phone book: user may set contacts in this page, and the contacts will be saved in the memory. Then using the pbook, vol+,vol-,menu/ok and exit keys to choose your friend in th...

  • Page 33

    Ag-188 user manual 33 / 53 2.9.4 time set: server:type the ip address of time server timezone:select correct time zone in list box timeout: longest response time for sntp manual timeset:the time setting daylight: daylight saving time 2.1.1 reboot: reboot ip phone, some setting needs to reboot to mak...

  • Page 34

    Ag-188 user manual 34 / 53 3 use normal phone to pre-configure ag-188 gateway user may pre-config ag-188 gateway using a normal phone connecting to ag-188. Please refer the below command: notice: all command below can be end with # to speed response. "#****" /*reboot gateway*/ "#*000" /*clear settin...

  • Page 35

    Ag-188 user manual 35 / 53 4 telnet console 4.1 introduce 4.1.1 basic structure user may use telnet command to access and manage gateway. Ag-188 adopts tree structure for telnet. Every node contains its sub-nodes or local command. User can type “help” or “?” whenever to see sub-nodes and all local c...

  • Page 36

    Ag-188 user manual 36 / 53 4.2 global command global command is available under all nodes, ag-188 support following commands: command function example chinese set to chinese ui #chinese clear clear telnet screen #clear english set to english ui #english exit return to parent-node #exit help 1． show ...

  • Page 37

    Ag-188 user manual 37 / 53 5 tree structure 5.1.1 account path: # [stop]start syslog ---syslog [no] start configure syslog server address and port ---syslog server –ip x.X.X.X _port xxx example: ##server –ip 202.112.20.10 show syslog settings ---syslog show show all account settings ---show 5.1.2 co...

  • Page 38

    Ag-188 user manual 38 / 53 delete digital map rule ---no entry –prefix xxx example: #no entry –prefix 010 show current digital map ---show ¾ lan interface settings path: # [disable]enable bridge mode ---[no]bridgemode [disable]enable dhcp service ---[no]dhcp-server [disable]enable nat ---[no]nat sho...

  • Page 39

    Ag-188 user manual 39 / 53 [disable]enable ftp alg ---[no]ftpalg [disable]enable ipsec alg ---[no]ipsecalg [disable]enable pptp alg ---[no]pptpalg add tcp mapping rule ---tcp-entry –ip x.X.X.X –lanport xxx –wanport xxx example:#tcp-entry –ip 192.168.1.5 –lanport 1720 –wanport 1000 delete tcp mapping...

  • Page 40

    Ag-188 user manual 40 / 53 ---entry –number xxx –ip x.X.X.X –protocol xxx _all xxx example:#entry –number 100 –ip 202.112.20.100 –protocol sip _all 123( user dial 100 and gateway will sent 100 instead) add number-ip bond and delete the prefix of the destination number ---entry –number xxx –ip x.X.X....

  • Page 41

    Ag-188 user manual 41 / 53 ¾ pppoe settings path: # pppoe account settings ---auth –user xxx -password xxx example:#auth –user aaa –password 123456 [disable]enable service settings ---[no]service xxx show pppoe settings ---show ¾ qos settings path: # [delete]add qos table entry --- [no]entry –addr x...

  • Page 42

    Ag-188 user manual 42 / 53 ¾ user management path: # change user right. ---access –user xxx –access xxx example:#access –user aaa –access 7 change user password ---password –user xxx add new user ---entry –user xxx –access xxx example:#entry –user abc –access 7 delete user entry ---no entry –user xx...

  • Page 43

    Ag-188 user manual 43 / 53 5.1.3 debug (level 0~7) path: # show debug setting ---show [disable]enable debug all modules ---[no] all xxx [disable]enable debug app module ---[no] app xxx [disable]enable debug cdr module ---[no] cdr xxx [disable]enable debug sip module ---[no] sip xxx [disable]enable d...

  • Page 44

    Ag-188 user manual 44 / 53 example: ##capability ¾ debugging path: # show debug info example:##debugging ¾ dhcp-server path: # show lan status and dhcp server info example:## dhcp-server ¾ dial-rule path: # show digital-map info example:## dial-rule ¾ interface path: # show lan info example:##interf...

  • Page 45

    Ag-188 user manual 45 / 53 show ip packets stat. Example:##ip ip show rtp packets stat. Example:##ip rtp show tcp packets stat. Example:##ip tcp show udp packets stat. Example:##ip udp ¾ memory path: # show gateway memory example:##memory ¾ nat path: # show nat information example:##nat ¾ port path:...

  • Page 46

    Ag-188 user manual 46 / 53 ¾ pppoe path: # show pppoe info example:## pppoe ¾ qos path: # show qos table info example:##qos ¾ sip path: # show sip info example:##sip ¾ udptunnel path: # show udp tunnel info example:## udptunnel ¾ uptime path: # show running time example:## uptime ¾ version path: # s...

  • Page 47

    Ag-188 user manual 47 / 53 set sntp ip address ---sntp server x.X.X.X set sntp server timeout ---sntp timeout xxx set timezone (-12~+12) ---sntp zone xxx show sntp info ---sntp show show current time ---print 5.1.10 tracert trace network path info usage: #tracert –host example:#tracert www.Google.Co...

  • Page 48

    Ag-188 user manual 48 / 53 6 network diagnosis there are some telnet commands for checking your network. Now listing below for your information command function example ping check if the destination is accessible #ping www.Google.Com tracert show network path info #tracert www.Google.Com show basic ...

  • Page 49

    Ag-188 user manual 49 / 53 8 post mode(safe mode) ag-188 provide safe mode. When there is booting problem because of setting problem or firmware problem. User can restore the factory setting or upgrade to a new firmware to solve this problem. How to enter safe mode? In the ag-188 booting procedure, ...

  • Page 50

    Ag-188 user manual 50 / 53 9 faq how many sip servers may ag-188 register simultaneously? Ag-188 support 2 sip servers and a iax server. The default server is sip . If you want to use the iax server you must set iax as default protocol in the iax config page. Iax and sip can register simultaneously ...

  • Page 51

    Ag-188 user manual 51 / 53 this dial-rule. Prefix match means that if prefix of the number that the user dials is the same as the prefix, the call will use this dial-rule, to distinguish from the full match case, you need to add “t” after the prefix number in the phone number setting. Call mode: sup...

  • Page 52

    Ag-188 user manual 52 / 53 how to use speed dial function? Please refer to “how to use dial rule?”. How to configure digital map? Please refer digit map settings. How to use call forward, call transfer and 3-way conference calls? User may set up the configuration in the call service page to use thes...

  • Page 53

    Ag-188 user manual 53 / 53 if a is the ag-188 user, and b calls and talking with a through voip. A can press the hook-flash to hold the call with b, and then press * and then enter c’s number. B will be transferred to c and can talk with c. ¾ 3-way conference calls check enable three way call assume...