Protek Samurai 321B Instruction Manual - page 18
15
20
E N G I N E I N S TA L L AT I O N
Make sure that the vehicles engine mount surfaces are level, and on the same plane.
Poor installation may cause distortion of the crankcase, bearings, etc, resulting in erratic
performance and permanent damage.
The recommended screws for securing the engine are Allen head, hexagon socket type 3mm
or 4-40 steel screws.
If existing holes in the engine mount do not align perfectly with the engine mounting lugs in
the crankcase, enlarge the holes in the lugs slightly with a needle file so that the screws are
perfectly aligned with the engine mount holes.
• Do not allow the bottom of the crankcase to touch the chassis.
• If needed, chamfer the inside edges of the engine mounts for clearance.
Piston
Cylinder Liner
Crankshaft
Near TDC
Slight taper
When the engine is cold.
When the engine is hot.
Low Speed Needle
(Metering Needle)
Idle Screw
(Throttle Stop Screw)
Mid Needle
(Mixture Control Valve)
High Speed
Needle
(Needle Valve)
Thermo Insulator
Carburetor Restrictor (Venturi)
Ball Link
Slide Boot
Exhaust
Gasket
Glowplug
Retaining Screw
O-Ring
O-Ring
Do not allow
bottom of crankcase
to touch chassis
Chamfer inside edges of bearers
Rotate the retainer
nut gently until it stops
Tighten a further
120º - 180º
High Speed
Needle
Open
Close
approx 0.5mm
Element glows when energized
Pliers
Replace the plug when the
element does not glow or is
burnt out.
Glow Plug Igniter
Turn the high speed needle clockwise
until it stops. This is the fully closed
position. Do not force it to turn further.
Approx. 0.5mm open
factory setting with the
restrictor removed.
Fuel
Fuel Tank Side
approx 1mm
Deliver fuel to the carburetor High speed needle position when
starting the engine.
Needle
30º
Close the high speed
needle approximately
30° as needed. This
procedure will be repeated
several times throughout
the break-in process.
Idle Screw
High Speed Needle
Low Speed Needle
Open
Close
Close
Open
HIGH SPEED NEEDLE
LOW SPEED NEEDLE
More fuel
Less fuel
More fuel
Less fuel
Mid Needle
Carburetor Body
Slide Valve
Carburetor Body
Low Speed Needle
Rotate the low speed needle until the head
sticks out 0.5mm from the ball link body.
This is the standard position.
Ball Link
First rotate the mid needle until its slotted
head is flush with the carburetor body. This is the
standard position.
5.5 turns out. Make adjustments with the slide in the open position.
2¾ turns out. Make adjustments with the slide in the open position!
Dirt and dust may lodge in marked places
7
8
NOTE: In the event that you replace any of the major engine components (piston,
sleeve, con rod, crankshaft or bearings), a brief break-in should be performed. If you
change to a fuel with higher nitro content, the engine will need to be re-tuned.
H O W T O S T O P T H E E N G I N E
To stop the engine during normal operation, reduce the throttle to neutral, flip the car over
and push a blunt rubber object against the flywheel.
DO NOT use your fingers!
W A R N I N G !
Do not touch rotating parts, the engine, or the tuned pipe; these components get
extremely hot and contact with them may result in a serious burn or other injury.
Piston
Cylinder Liner
Crankshaft
Near TDC
Slight taper
When the engine is cold.
When the engine is hot.
Low Speed Needle
(Metering Needle)
Idle Screw
(Throttle Stop Screw)
Mid Needle
(Mixture Control Valve)
High Speed
Needle
(Needle Valve)
Thermo Insulator
Carburetor Restrictor (Venturi)
Ball Link
Slide Boot
Exhaust
Gasket
Glowplug
Retaining Screw
O-Ring
O-Ring
Do not allow
bottom of crankcase
to touch chassis
Chamfer inside edges of bearers
Rotate the retainer
nut gently until it stops
Tighten a further
120º - 180º
High Speed
Needle
Open
Close
approx 0.5mm
Element glows when energized
Pliers
Replace the plug when the
element does not glow or is
burnt out.
Glow Plug Igniter
Turn the high speed needle clockwise
until it stops. This is the fully closed
position. Do not force it to turn further.
Approx. 0.5mm open
factory setting with the
restrictor removed.
Fuel
Fuel Tank Side
approx 1mm
Deliver fuel to the carburetor High speed needle position when
starting the engine.
Needle
30º
Close the high speed
needle approximately
30° as needed. This
procedure will be repeated
several times throughout
the break-in process.
Idle Screw
High Speed Needle
Low Speed Needle
Open
Close
Close
Open
HIGH SPEED NEEDLE
LOW SPEED NEEDLE
More fuel
Less fuel
More fuel
Less fuel
Mid Needle
Carburetor Body
Slide Valve
Carburetor Body
Low Speed Needle
Rotate the low speed needle until the head
sticks out 0.5mm from the ball link body.
This is the standard position.
Ball Link
First rotate the mid needle until its slotted
head is flush with the carburetor body. This is the
standard position.
5.5 turns out. Make adjustments with the slide in the open position.
2¾ turns out. Make adjustments with the slide in the open position!
Dirt and dust may lodge in marked places
7
8