1. DL manuals
  2. Protos
  3. Toy
  4. MAX2
  5. Instruction Manual

Protos MAX2 Instruction Manual

Summary of MAX2

  • Page 1

    R instructions manual instructions manual 1 main rotor diameter................. 1577mm (700mm blades) tail rotor diameter.................. 286mm (105mm tail blades) length without main blades.......1371mm length with main blades...........1757mm (700mm blades) overall height..........................

  • Page 2

    Pages content 3 safety rules 4 tools required for assembly 5 r/c equipment required to complete 6 motor pinion teeth choice 7 how to read this manual 8-29 main frame assembly 30-42 tail assembly 43 cyclic servos 44-50 head assembly 51-52 brain, esc, bec 53-54 battery installation 55 main blades inst...

  • Page 3

    R always follow these rules for safety instructions manual 3 operate the helicopter in open areas with no people nearby. Do not operate the helicopter in the following places and situations (or else you risk severe accidents): -in places where children gather or people pass through -in residential a...

  • Page 4

    R tools required for assembly instructions manual 4 thrust bearing grease slow curing epoxy philips screw driver where indicated use thread lock medium open-end wrench 7mm hexagon screw drivers : 1,5mm 2mm (need with handle and long tip) 2,5mm - 4mm two 5 mm (spindle) hexagon l-key 2,5mm.

  • Page 5

    R r/c equipment required for assembly instructions manual 5 main blades: standard full carbon blades 690mm - 716mm 750mm - 800mm need 800 conversion kit protos max v2 art. Msh71165 tail blades: standard full carbon blades 105mm to 115mm bec esc : at least 160 a high voltage swashplate servos support...

  • Page 6

    23t art. Msh71181 (optional) r motor pinion teeth choice instructions manual 6 fly style beginner sport soft 3d hardcore 3d pinion 18t art. Msh71137 (optional) 19tart. Msh71179 (optional) 20t art. Msh71138 rpm (520kv motor) 1800 1950 2100 2350 3d 21t art. Msh71180 (optional) 2150 hard 3d 22t art. Ms...

  • Page 7

    R how to read this manual instructions manual 7 box where you can find all big parts box and bag where you can find washers, bearings, screws and all other small parts msh spare part code apply a thin layer of threadlock on the external part of the ball bearing pay attention to the instruction steep...

  • Page 8

    R box a instructions manual 8 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a1 main plastic frame v2 art. Msh7163 landing gear art. Msh71001 washer 3.1x8x1 hex screw m3x10 art. Msh71114.

  • Page 9

    Guide pulley support - front side - guide pulley - front side - hex screw m3x8 art. Msh71109 ball bearing 10x19x5 art. Msh71071 hex screw m4x8 art. Msh71117 motor mount art. Msh71132 r box g instructions manual 9 where i can find the big parts where i can find screws, ball bearings and stuff like th...

  • Page 10

    R box e instructions manual 10 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a1 ball bearing 6x19x6 art. Msh71135 hex screw m4x16 art. Msh71131 motor 4530 - 500kv art. Msh71134 optional ball bearing 8x19x6 art. Msh71162 for 6mm motor shaft for 8m...

  • Page 11

    R instructions manual 11 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a1 m4x4 socket screw art. Msh71122 hex screw m4x16 art. Msh71093 pinion 20t art. Msh71138 pinion adapter for 6mm motor shaft art. Msh71147 38 - 49mm 23mm 34mm 6 - 8mm.

  • Page 12

    R box instructions manual 12 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a2 ball bearing 6x12x4 art. Msh71082 hex screw m3x5 art. Msh71140 ball bearing 6x10x2,5 art. Msh51073 guide pulley support - back side - guide pulley arm - back side - spr...

  • Page 13

    R box g instructions manual 13 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a2 hex screw m4x10 art. Msh71101 frame rear plate art. Msh71017.

  • Page 14

    R box instructions manual where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a + a2 hex screw m3x8 art. Msh71109 tail boom frame clamp art. Msh71028 do not fully thighten yet 14.

  • Page 15

    R box g + b instructions manual 15 where i can find the big parts where i can find screws, ball bearings and stuff like that box f b ag a2 + b1 rear belt tension regulation front belt tension regulation hex screw m3x8 art. Msh71109 x carbon frame art. Msh71018 frame central plate art. Msh71157 hex s...

  • Page 16

    R box a instructions manual 16 where i can find the big parts where i can find screws, ball bearings and stuff like that box hex screw m3x6 art. Msh71108 oneway top oneway hub oneway shaft ball bearing 17x23x4 art. Msh71146 oneway bearing pre-assembled.

  • Page 17

    R box a instructions manual 17 where i can find the big parts where i can find screws, ball bearings and stuff like that box hex screw m3x6 art. Msh71108 main pulley v2 art.Msh71149 1 tighten untill completely seated 2 3 tighten 1/8 turn pre-assembled.

  • Page 18

    R box a instructions manual 18 where i can find the big parts where i can find screws, ball bearings and stuff like that box hex screw m3x6 art. Msh71108 autorotation pulley art.Msh71150 autorotation pulley support pre-assembled 1 tighten untill completely seated 2 3 tighten 1/8 turn.

  • Page 19

    R box instructions manual 19 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a2 main shaft hollow v2 art.Msh71151 hex screw m5x25 art. Msh71118 m5 nut art. Msh71098 short dimension.

  • Page 20

    R box a + box b instructions manual 20 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a2 apply grease on thrust bearing front belt art.Msh71154 tail belt 700 art.Msh71152 ball bearing 12x24x6 art. Msh71155 internal hole smaller internal hole bigge...

  • Page 21

    R instructions manual 21 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a2 main shaft locking ring art. Msh71025 hex screw m3x10 art. Msh71114.

  • Page 22

    R box b instructions manual 22 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a+a3 carbon main frame v2 art. Msh71156 magnet canopy support kit art. Msh71022 hex screw m3x10 art. Msh71114.

  • Page 23

    R screws layout instructions manual 23 hex screw m3x10 art. Msh71114 hex screw m3x8 art. Msh71109.

  • Page 24

    R box b instructions manual 24 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a3 rectangular washer art msh71021 msh washer 3x8 art. Msh71091 hex screw m3x10 art. Msh71114 hex screw m3x8 art. Msh71109 do not fully thighten yet do not fully thighte...

  • Page 25

    R box instructions manual 25 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a3 check that screw goes inside the plastic housing 1 tighten slowly until completely seated 2 3 tighten 1/8 turn hex screw m3x10 art. Msh71114.

  • Page 26

    R box g instructions manual 26 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a3 hex screw m3x6 art. Msh71108 ball bearing 12x24x6 art. Msh71073 servo frame art. Msh71024 hex screw m3x8 art. Msh71109.

  • Page 27

    R instructions manual 27 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a4 do not fully tighten yet 1 tighten slowly until completely seated 2 3 tighten 1/8 turn rectangular washer art msh71021 hex screw m3x10 art. Msh71114 hex screw m3x8 art. Msh...

  • Page 28

    R box g instructions manual 28 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a4 ball bearing 12x21x5 art. Msh71072 msh washer 3x8 art. Msh71091 third bearing support art. Msh71023 press the bearing support upward against the main pulley and tight...

  • Page 29

    R box instructions manual 29 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag a5 hex screw m3x10 art. Msh71114 do not fully tighten yet hex screw m3x10 art. Msh71099 spring support - front side - spring bracket art. Msh71161 hard 3d sport / 3d begin...

  • Page 30

    To be used with 800mm main blades art. Msh71159 optional r box b instructions manual 30 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag b +b1 tail servo holder art. Msh71029 to be used with 700mm main blades art. Msh71158 short long b o o m.

  • Page 31

    Hex screw m3x14 art. Msh71112 hex screw m2,5x12 art. Msh71104 ball m2x4.8 art. Msh41009 m2 nut art. Msh71095 tighten the six tail clamp screws r box b instructions manual 31 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag b +b1 level 15mm carbon se...

  • Page 32

    R box instructions manual 32 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag b+b1 tail rod clamp art. Msh71036 hex screw m3x12 art. Msh71106 m2 nut art. Msh71095 hex screw m2x10 art. Msh71102 do not fully tighten yet front check the direction of th...

  • Page 33

    R box c instructions manual 33 where i can find the big parts where i can find screws, ball bearings and stuff like that box hex screw m2,5x12 art. Msh71104 tail pulley plate tail pulley tail pulley art. 71141 pre-assembled.

  • Page 34

    R box c instructions manual 34 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c1 alu tail frame tail shaft art. 71040 ball bearing 6x15x5 flanged art. Msh71074 tail box art. 71037 hex screw m3x20 art. Msh71107 ball bearing 6x12x4 art. Msh71082 tai...

  • Page 35

    Tail pitch lever support art. Msh71042 tail pitch lever art. Msh71160 r box c instructions manual 35 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c+c1 tail pitch carbon lever art. Msh71043 art. Msh71160 tail pitch lever screw m2,5x5 art. Msh7112...

  • Page 36

    R box instructions manual 36 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c2 check the rotation direction during the installation of the belt 1 alignment slot 2 3 4 alignment pin art. Msh71037 art. Msh71044 hex screw m3x14 art. Msh71112 y tail b...

  • Page 37

    R box instructions manual 37 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c2 pre-assembled idler pulley bushing idler pulley tail pulley support hex screw m3x8 art. Msh71109 idler pulley tail art. Msh71143 do not overtighten. Idler pulley must s...

  • Page 38

    Hex grub screw m4x4 art. Msh71122 r box b instructions manual 38 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c2 pin 1,5x8 art. Msh71045 tail plastic rod art. Msh71045 art. Msh71048 tail pitch assembly art. Msh71045 1 2 3 vertical fin art. Msh71...

  • Page 39

    R box instructions manual 39 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c + c2 ball bearing 5x10x4 art. Msh71081 art. Msh71048 washer 5x7,5x0,2 art. Msh71048 washer 7,5x9,8x0,2 art. Msh71048 hex screw m2,5x10 art. Msh71103 art. Msh71048 hex sc...

  • Page 40

    R box b instructions manual 40 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c2 hex screw m3x23 art. Msh51151 art. Msh71048 m3 nut art. Msh71096 art. Msh71048.

  • Page 41

    R box b instructions manual 41 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c3 hex screw m4x16 art. Msh71049 art. Msh71086 hex screw m4x10 art. Msh71116 m4 nut art. Msh71097 to be used with 700mm main blades art. Msh71049 short long to be used w...

  • Page 42

    R box b instructions manual 42 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag c3 uniball hand m2.5 art. Msh71083 15mm remove coating with sandpaper apply a film of slow curing epoxy wait completely curing and mount it on the model 3 4 5 1 2 hex sc...

  • Page 43

    R box instructions manual 43 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag d+d1 hex screw m2,5x10 art. Msh71103 ball m3x4 art. Msh71089 hex screw m2.5x8 art. Msh71111 servo horn 19mm msh71052 carbon servo washer art. Msh71032 art. Msh71050 art. M...

  • Page 44

    R box c instructions manual 44 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e1 ball m3x4 art. Msh71089 bushing 3x5x3 art. Msh71053 ball bearing 3x6,5x2,5 art. Msh71078 swashplate art. Msh71053 hex screw m3x12 art. Msh71106.

  • Page 45

    R box c instructions manual 45 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e+e1 hex screw m3x8 art. Msh71109 screw m5x25 art. Msh71118 m5 nut art. Msh71098 anti swashplate spin carbon art. Msh71054 main hub art. Msh71055.

  • Page 46

    R box instructions manual 46 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e+e1 hex screw m3x12 art. Msh71106 spindle art. Msh71058 art. Msh71056 sport / 3d art. Msh71057 hard 3d 700 blades 3d 800 blades optional h e a d d a m p e n e r s step vi...

  • Page 47

    R box c instructions manual 47 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e1 ball m3x4 art. Msh71089 hex screw m3x8 art. Msh71109 ball bearing 10x19x5 art. Msh71071 thrust 10x18x5,5 art. Msh71076 washer 10x16x1 art. Msh71059 main blade holder ...

  • Page 48

    Step outside the main hub r box instructions manual 48 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e1 spindle spacer art. Msh70056 art. Msh71057 washer cnc 6,1x14x2.5 art. Msh71058 screw m6x16 art. Msh71058 art. Msh71120

  • Page 49

    R box c instructions manual 49 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e1 pin 2x12 art. Msh71061 art. Msh71062 ball bearing 3x8x4 art. Msh71080 spacer 3x5x0.5 art. Msh71061 hex grub screw m3x3 art. Msh71121 hex screw m3x14 art. Msh71112 was...

  • Page 50

    R box instructions manual 50 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e2 uniball hand m2.5 art. Msh71083 uniball hand m2.5 art. Msh71083 servo rods set m2.5 x 57.8mm art. Msh71064 head rods set m2.5 x 49mm art. Msh71063 37,5mm 29mm head rod ...

  • Page 51

    R box b + box d instructions manual 51 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e2 hex screw m3x5 art. Msh71100 carbon cover frame rear plate art. Msh71016 brain art. Msh51600

  • Page 52

    R box d instructions manual 52 where i can find the big parts esc msh by yge 160 hv art. Msh71069 optional bec (not included).

  • Page 53

    R box b instructions manual 53 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag b1 hex screw m3x10 art. Msh71099 plastic - battery support slide art. Msh71066 carbon - battery support slide art. Msh71066 battery oring set art. Msh71067.

  • Page 54

    R battery slide instructions manual 54 to remove the battery 1 - push back the slide 2 - push the button.

  • Page 55

    R box instructions manual 55 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e2 hex screw m5x35 art. Msh71119 m5 nut art. Msh71098.

  • Page 56

    R box a instructions manual 56 where i can find the big parts where i can find screws, ball bearings and stuff like that box f bag e2 painted canopy fg classic scheme art. Msh71065 hex screw m3x8 art. Msh71109 msh washer 3x8 art. Msh71091 1 2 3.

  • Page 57

    R main blades pitch check instructions manual 57 where i can find screws, ball bearings and stuff like that box f bag e2 main and tail blades pitch checker art. Msh71126 90° 90° 0° 90° 1 2 4 set transmitter and brain to 0° 5 -12° -6° 0° +6° +12° tighten the 3 servo horn screws pitch indicator 3.

  • Page 58

    R tail blades pitch check instructions manual 58 1 3 4 2 90° 90° main and tail blades pitch checker art. Msh71126.

  • Page 59

    R belt tension check - tail side instructions manual 59 loose to adjust the belt tighten to fly belt tensioner correct position.

  • Page 60

    R belt tension check - motor side instructions manual 60 tighten to increase the belt tension loose to decrease the belt tension loose to adjust the belt tighten to fly distance 42,8mm 43,8mm 44,8mm 45,8mm 46,8mm 47,8mm pinion 18t 19t 20t 21t 22t 23t.

  • Page 61

    R upgrades instructions manual 61 landing gear - gorilla gear msh71051 msh71057 msh71165 msh71172 servo horn adapter jr (2x) head dampeners 3d (red) 800 conversion kit protos max v2 msh71166 main plastic frame v2 - white msh71168 guide pulley - 10mm - metal pinion 21t v2 msh71173 msh71174 msh71177 m...

  • Page 62

    R instructions manual 62 specifcation and design are subject to change without notice loctite, uhu plus, spektrum, futaba, hott and multiplex are registered trademarks msheli s.R.L. Uboldo (va) italy.