1. DL manuals
  2. Protos
  3. Toy
  4. RC Helicopter
  5. Instruction Manual

Protos RC Helicopter Instruction Manual

Summary of RC Helicopter

  • Page 1

    Instructions manual rc helicopter main rotor diameter : 965mm tail rotor diameter : 192mm lenght without main blades : 892mm lenght with main blades : 1122mm main blades lenght : 425mm overall height : 282mm tail rotor - main rotor ratio : 4,65 main pulley : 93t weight ready to fly with 6slipo : 150...

  • Page 2

    Instructions manual rc helicopter page content 1-7 8-17 18-26 27-29 30 31 main frame assembly head assembly tail assembly motor installation battery, esc and canopy installation belt tensioning diagram index.

  • Page 3

    1 tips/instructions hex screw m2.5x5 only on lower servo frame. Bag- a hex screw m2.5x5 msh 50101 ball screw m2x4.8 msh 50007 nut m2 msh 50123 hex screw m2.5x5 msh 50101 hex screw m2x10 msh 50099 hex screw m2x10 msh 50099 servo adapter msh 50086 ball screw 4.5x10.5 msh 50007 nut m2 1.4x4 msh 50123 n...

  • Page 4

    Guide pulley spacer 3x5x0.6 msh 50018 guide pulley spacer 3x5x0.6 msh 50018 pin 3x14 msh 50059 pin 3x14 msh 50059 bb 3x8x3 msh 50033 guide pulley msh 50091 2 bag- b.

  • Page 5

    3 bag- b hex screw m2.5x6 msh 50102 hex screw m2.5x8 msh 50103 hex screw m2.5x8 msh 50103 motor mount msh 50028 washer 2.6x6.5x1.5 msh 50146 hex screw m2.5x6 msh 50102 attention ! Caution use thread lock on every screw metal/metal such as screws that keep the servo frame in place. Washer 2.6x6.5x1.5...

  • Page 6

    4 main frame l msh 50070 main frame r msh 50066 hex screw m2.5x6 msh 50102 hex screw m2.5x8 msh 50103 washer 2.6x6.5x1.5 msh 50146 nylon nut m2.5 msh 50124 hex screw 2.5x16 msh 50106 self tapping screw msh 50118 hex screw m2.5x6 msh 50102 m2.5 nylon nut msh 50124 hex screw m2.5x16 msh 50106 washer 2...

  • Page 7

    5 ! Caution tips/instructions bag- b hex screw m2.5x10 msh 50104 hex screw m2.5x16 msh 50106 nylon nut m2.5 msh 50124 nylon nut m2.5 msh 50124 slide skid in both struts until "clicks" in position. Both struts should "click". Do not fully tighten hex screws 2.5x16 yet as they are used later to keep b...

  • Page 8

    6 tips/instructions bag- b grub screw m2.5x12 msh 50115 msh 50080 msh 50063 grub screw m2.5x12 msh 50115 hex screw m2.5x8 msh 50103 hex screw m2.5x8 msh 50103 use thread lock on grub screw m2.5x12 on the side that goes in the servo frame. Grub screw can be screwed in by hand and tightened with msh 5...

  • Page 9

    7 tips/instructions very important !! Bag- c hex screw m2x6 msh 50098 msh 50023 msh 50004 hex screw m2x6 msh 50098 hex screw m3x20 msh 50112 hex screw m3x20 msh 50112 nylon nut m3 msh 50125 nylon nut m3 4.3x5.5 msh 50125 hex screw m3x8 msh 50110 hex screw m3x8 msh 50110 washer 3.1x10x1 msh 50121 was...

  • Page 10

    Hex screw m2x10 msh 50099 spacer 2x3x2.5 msh 50021 bb 2x5x2.5 msh 50039 ball m2x2.8 msh 50009 msh 50024 8 tips/instructions use thread lock on balls and screw m2x10. Bag- c hex screw m2x10 msh 50099 ball screw m2x2.8 msh 50009.

  • Page 11

    9 tips/instructions rod d 42.5mm msh 50046 uniball hand l msh 50092 bag- c fut 3150 fut 9650 rod d 42.5mm msh 50046 25.6 mm 28 mm length of rods connecting servos to swashplate is correct if using 9650 or 3150 fut servo other servos might need adjustment. Use provided ball sizer on plastic links in ...

  • Page 12

    10 ! Caution bag- d ball screw m2x4.8 msh 50007 ball screw m2x4.8 msh 50007 bb 2x5x2.5 flanged msh 50041 hex screw m2x10 msh 50099 msh 50084 msh 50037 hex screw m2x10 msh 50099 pin 2x12 msh 50058 washout pin 2x12 msh 50058 msh 50037 do not over tight screws and balls on plastic.Just 1/8 turn after c...

  • Page 13

    11.

  • Page 14

    12 tips/instructions ! Caution tips/instructions bag- d hex screw m2.5x5 msh 50101 bb 2x5x2.5 flanged msh 50091 bb 2.5x6x2.5 flanged msh 50093 msh 50027 msh 50085 hex screw m2.5x5 msh 50101 apply thread lock on hex screw m2.5x5 and outside bb 2.5x6x2.5. While tightening screw m2.5x5 to flybar carrie...

  • Page 15

    13 tips/instructions bag- d rod a 16.4 mm msh 50048 5.4 mm hex screw m2x6 msh 50098 hex screw m2x6 msh 50098 grub screw m3x3 msh 50117 grub screw m3x3 msh 50117 uniball hand s msh 50036 rod a 16.4mm msh 50048 flybar rod msh 50010 (contained in bag l) msh 50026 msh 50008 use thread lock on screws m2x...

  • Page 16

    14 bag- d hex screw m2x6 msh 50098 hex screw m2x6 msh 50098 grub screw m3x3 msh 50117 grub screw m3x3 msh 50117 msh 50088 paddle weight msh 50062 brass 2.4x 5mm 92.5 mm 92.5 mm.

  • Page 17

    15 bag- d ball screw m2x4.8 msh 50007 msh 50083 msh 50082 bb 2x5x2.5 flanged msh 50041 ball screw m2x4.8 msh 50007 hex screw m2x10 msh 50099 hex screw m2x10 msh 50099 bb 5x10x4 msh 50034 thrust bb 5x10x4 msh 50042 inside (i) outside (o) bb 5x10x4 msh 50034 washer 5x7.5x0.2 msh 50135 bag- d washer 5x...

  • Page 18

    16 tips/instructions ! Caution bag- d use thread lock on screws m3x8. Thrust bearings flange with bigger hole inward, flange with smaller hole outward. Spindle spacer is a stepped washer, please make sure that, the stepped side faces bb 5x10x4. Hex screw m3x8 msh 50110 hex screw m3x8 msh 50110 washe...

  • Page 19

    17 bag- d tips/instructions use threadlock on m3x14 screw. Hex screw m3x14 msh 50113 hex screw m3x14 msh 50113 rod b 12 mm msh 50049 rod c 53 mm msh 50047 37.3mm rod c uniball hands msh 50032 1 mm rod b uniball hand s msh 50036 user to have 2 sets of: msh 50036 note: user to have 2 sets of: msh 5003...

  • Page 20

    18 bag- e self tapping screw 2.2x9.5 msh 50118 self tapping screw 2.2x9.5 msh 50118 msh 50064 click pulley assembly in position click pulley assembly in position pin 3x14 msh 50059 bag- e pin 3x14 msh 50059 bb 3x8x3 msh 50033 guide pulley msh 50091 guide pulley assembly.

  • Page 21

    19 tips/instructions important !! Hex screw m2.5x12 msh 50105 hex screw m2.5x12 msh 50105 nylon nut m2.5 msh 50124 nut m2 1.4x4 msh 50123 hex screw m2x10 msh 50099 hex screw m2.5x42 msh 50109 ball screw m2x4.8 msh 50007 msh 50074 msh 50086 bag- e do not fully tighten screws m2.5x12 yet. When sliding...

  • Page 22

    20 tips/instructions do not over tight guide pulley screw, check that it turns freely after tightening the screw. Bag- f hex screw m2.5x20 msh 50107 hex screw m2.5x16 msh 50106 hex screw m2.5x20 msh 50107 guide pulley bushing 2.5x3x7.8 msh 50019 hex screw m2.5x16 msh 50106 pin 1.5x12 msh 50144 pin 1...

  • Page 23

    Pin 1.5x8 msh 50057 bb 7x11x3 msh 50036 msh 50061 msh 50095 msh 50093 msh 50094 21 ! Caution bag- f pin 1.5x8 msh 50057 tail pitch plate msh 50099, must screw in to slide shaft msh 50061 perfectly squared..

  • Page 24

    22 tips/instructions tips/instructions bag- f bag- f tail pitch lever screw m2.5x5 msh 50100 pitch lever bush 2.5x3x8.6 msh tail pitch lever screw m2.5x5 msh 50100 ball screw m2x4.8 msh 50007 ball screw m2x4.8 msh 50007 bb 3x6x2.5 msh 50037 msh 50077 nylon nut m2.5 msh 50124 nylon nut m2.5 msh 50124...

  • Page 25

    23 tips/instructions tips/instructions bag- f hex screw m3x12 msh 50111 bb 3x8x4 msh 50035 msh 50076 msh 50022 hex screw m3x12 msh 50111 ball screw m2x4.8 msh 50007 ball screw m2x4.8 msh 50007 bag- f grub screw m3x3 msh 50117 grub screw m3x3 msh 50117 apply thread lock to grub screw m3x3. Make sure ...

  • Page 26

    24 tips/instructions bag- f hex screw m3x12 msh 50111 hex screw m3x12 msh 50111 bag- f hex screw m2.5x16 msh 50106 apply thread lock to m3x12 screws. Hex screw m2.5x16 msh 50106 nylon nut m2.5 msh 50124 nylon nut m2.5 msh 50124 tail blades msh 50050 (contained in bag l).

  • Page 27

    25 tips/instructions tips/instructions bag- g bag- g glue part msh 50065 with slow curing epoxy glue. Msh 50065 msh 50065 tail boom braces 343 mm msh 50050 (containded in bag l) nylon nut m2.5 msh 50124 nylon nut m2.5 3x5 msh 50124 hex screw m2.5x25 msh 50108 hex screw m2.5x25 msh 50108 msh 50067 ms...

  • Page 28

    26 tips/instructions bag- g 35 mm rod e 35mm msh 50045 rod e 35mm msh 50045 control rod 320 mm msh 50051 (contained in bag l) rod e 35mm msh 50045 msh 50092 uniball hand l msh 50092 glue rod e with slow curing epoxy make sure 1mm not threaded part of rod e is protruding..

  • Page 29

    27 tips/instructions apply thread lock to m3x8 hex screw. Hex screw m3x8 msh 50110 msh 50126 hex screw m3x8 msh 50110 washer 3.1x8x1 msh 50122 washer 3.1x8x1 msh 50122.

  • Page 30

    28 make sure there is about 1mm gap between bottom of motor adapter (msh 50006) and motor mount (msh 50028) when tightened in position. ! Caution tips/instructions hex grub screw m3x3 msh 50117 msh 50006 apply thread lock to m3x5 grub screw. Grub screw m3x3 msh 50117.

  • Page 31

    29 washer 3.1x10x1 msh 50121 washer 3.1x10x1 msh 50121 free spin msh 50052 motor pulley 18t msh 50121 while inserting make sure that the pinion spins freely clockwise looking from above..

  • Page 32

    30 tips/instructions use o ring msh 50053 to secure battery (not provided in the kit) in place. Use o ring msh 50060 to secure esc (not provided in the kit) in place..

  • Page 33: Belt Tension Adjustment

    31 belt tension adjustment pressing the belt moderately, it should move 2-3 mm. Test tension as indicated in the picture..

  • Page 34

    32 spare code spare description part code part description part qty msh51001 metal flybar control arm ¬ 06+ &urvvedoo ¬ ¬ 06+ )o\edudup ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[juxevfuhz0[ 06+ 6slqgoh¬ ¬ ¬ ¬ ¬ 06+ 6slqgoh ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ 6slqgohzdvkhu[[ 06+ +hdggdpshqhuv¬ ¬ ¬ ¬ 06+ 6slqgohvsdfhu ¬ ¬...

  • Page 35

    33 spare code spare description part code part description part qty 06+ 3lqlrq7¬ ¬ ¬ ¬ 06+ 0rwrusxooh\7 ¬ ¬ 06+ 2qhzd\%%[[ ¬ ¬ 06+ %%[[ ¬ ¬ 06+ (ulqj ¬ ¬ 06+ :dvkhu[[ 06+ 3lqlrq7¬ ¬ ¬ ¬ 06+ 0rwrusxooh\7 ¬ ¬ 06+ 2qhzd\%%[[ ¬ ¬ 06+ %%[[ ¬ ¬ 06+ (ulqj ¬ ¬ 06+ :dvkhu[[ ¬ ¬ ¬ ¬ ¬ 06+ 3lqlrq7¬ ¬ ¬ ¬ 06+ 0...

  • Page 36

    34 spare code spare description part code part description part qty 06+ :dvkrxwkxe¬ ¬ ¬ ¬ 06+ :dvkrxwkxe ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ ¬ ¬ ¬ 06+ +hdgurgvvhw¬ ¬ ¬ ¬ 06+ 5rg&pp ¬ ¬ 06+ 5rg$pp ¬ ¬ 06+ 5rg%pp ¬ ¬ ¬ ¬ ¬ 06+ 6huyrurgvvhw¬¬ ¬ ¬ 06+ 5rg'pp ¬ ¬ ¬ ¬ 06+ 7dlofrqwurourgvhw¬ ¬ ¬ ¬ 06+ 5rg(pp ¬ ¬ 06+ 7d...

  • Page 37

    35 spare code spare description part code part description part qty 06+ *xlghsxooh\v¬ ¬ ¬ ¬ 06+ *xlghsxooh\iudphvsdfhu 3x5x0.6 6 ¬ ¬ 06+ %%[[ ¬ ¬ 06+ 3lq[ ¬ ¬ 06+ *xlghsxooh\ ¬ ¬ ¬ ¬ ¬ 06+ %how¬ ¬ ¬ ¬ 06+ %how ¬ ¬ ¬ ¬ 06+ 3dggohv¬ ¬ ¬ ¬ 06+ sdggohzhljkw ¬ ¬ 06+ sdggoh ¬ ¬ ¬ ¬ ¬ 06+ 6huyrdgdswhuvhw¬ ...

  • Page 38

    36 spare code spare description part code part description part qty 06+ 7dloer[¬ ¬ ¬ ¬ 06+ %%[[ ¬ ¬ 06+ 7dloer[5 ¬ ¬ 06+ 7dloer[/ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ 0q\orqqxw ¬ ¬ ¬ ¬ ¬ 06+ 7dloslwfkohyhu¬ ¬ ¬ ¬ 06+ %doo0[ ¬ ¬ 06+ 7dloslwfkohyhuexvklqj ¬ ¬ 06+ %%[[ ¬ ¬ 06+ 7dloslwfkohyhu ¬...

  • Page 39

    37 spare code spare description part code part description part qty 06+ 0dlq3xooh\¬ ¬ ¬ ¬ 06+ 0dlqjhdu ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ 0q\orqqxw ¬ ¬ ¬ ¬ ¬ 06+ 0dlqiudphdvvhpeo\¬ ¬ ¬ ¬ 06+ 0dlqiudph5 ¬ ¬ 06+ 0dlqiudph/ ¬ ¬ 06+ *xlghsxooh\kroghu ¬ ¬ 06+ $qwlvzdvksodwhvslq ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuh...

  • Page 40

    38 spare code spare description part code part description part qty 06+ 6sduhvfuhzvhw¬ ¬ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ 0[6shfldowdloslwfk ohyhuvfuhz ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ¬ 06+ +h[vfuhz0[ ¬ ...

  • Page 41

    39 spare code spare description part code part description part qty 06+ %%[[¬ ¬ ¬ ¬ 06+ %%[[ ¬ ¬ ¬ ¬ 06+ %%[[¬ ¬ ¬ ¬ 06+ %%[[ ¬ ¬ ¬ ¬ 06+ %%[[¬ ¬ ¬ ¬ 06+ %%[[ ¬ ¬ ¬ ¬ 06+ %%[[)odqjhg¬ ¬ ¬ ¬ 06+ %%[[)odqjhg.