1. DL manuals
  2. ProVisual
  3. DVR
  4. 16 series
  5. User Manual

ProVisual 16 series User Manual

Manual is about: Standalone Digital Video Recorder

Summary of 16 series

  • Page 1

    Provisual standalone digital video recorder provisual dvr series h / fh / mh / vh / aqh 4 / 8 / 16 channel models user manual this document contains preliminary information and is subject to change without notice..

  • Page 2

    2 fcc compliance statement notice to users : this equipment has been tested and found to comply with the limits for a class a digital device. Pursuant to part 15 of the fcc rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated i...

  • Page 3

    3 cautions  this product has free voltages (100v and 240v). See installation instructions before connecting to the power supply.  this product uses a lithium battery.  to avoid any risk of explosion, do not replace the battery on the main board by anything other than a lithium battery.  dispose ...

  • Page 4

    4 12. Servicing  do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel. 13. Damage requiring service  unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions: ① when the power-suppl...

  • Page 5: The List Of Configuration

    5 the list of configuration dvr set provisual h series dvr : 4 / 8 / 16ch provisual fh / mh / aqh series dvr : 4 / 8 / 16ch cd (provisual cms pro/manual) remote controller screws hdd brackets rack bracket (except a and c type model) data cable power cable adapter (except e / h / i type model).

  • Page 6: Operation Precautions

    6 operation precautions  power off  do not turn dvr off, or plug off the power adapter while dvr is in operation (record/playback). Otherwise, it may cause permanent damage to the equipment. Please click (  ) setup>system>shutdown sequentially and then remove the power after dvr is shutdown compl...

  • Page 7: Table Of Contents

    7 table of contents dvr the equipment complies with the requirement of fcc cfr 47 part 15 subpart b, class a. ..................................................................... 2 explanation of graphical symbols .................................................... 2 warnings ........................

  • Page 8

    8 clear all data ............................................................................................ 32 4.2.2 admin ......................................................................................... 32 date ................................................................................

  • Page 9

    9 4.6.5 popup link ................................................................................. 60 5. Operation instruction .................................................................. 61 5.1 viewing.............................................................................................

  • Page 10

    10 12.1.3 site registration ................................................................. 103 12.1.4 connection .......................................................................... 104 12.1.5 search ................................................................................. 105 12.1....

  • Page 11: 1.  Product Features

    11 1. Product features 1.1 unpacking  this equipment is an electronic appliance, so it should be handled with special care.  after unpacking, please check if all the following items are included. - dvr main body - provisual h series dvr : power supply adapter (dc 12v, 5a) and power supply cable - ...

  • Page 12

    12 provisual dvr-824-fh / dvr-1648-fh.

  • Page 13

    13 provisual dvr-824-mh / dvr-1648-mh.

  • Page 14

    14 provisual dvr-824-vh / dvr-1648-vh.

  • Page 15

    15 provisual dvr-412-aqh / dvr-824-aqh / dvr-1648-aqh hd-sdi dvr.

  • Page 16

    16 provisual aqh series – dvr-400-aqh 4 channels dvr.

  • Page 17

    17 provisual – dvr-16214-aqh 16 channels hybrid dvr.

  • Page 18: 2.  Installation

    18 2. Installation 2.1 hard disk and dvd-rw installation 2.1.1 sata port provisual h series dvr - main substrate of this dvr has three sata ports: they are indicated as sata 1, 2 and sata 3. - please mount dvd-rw at the sata 3 port. Provisual fh series dvr - main substrate of this dvr has four sata ...

  • Page 19

    19 caution do not mount dvd-rw at sata 5 port. 2.1.3 e-sata external storage (d type)  this series dvr has 2 external sata ports; the picture above shows external sata 6-7 port.  6-7 sata port: it is designed to mount 4hdds per each external sata ports. 2.1.4 hdd installation  securely fix a hard...

  • Page 20

    20 2.1.6 dvd-rw installation  securely fix dvd-rw by using bracket and screws provided herewith.  please do not use any different dvd-rw cables (data cable and power supply cable) other than the ones we provide.  otherwise, it may cause damage to the dvd-rw.  only one dvd-rw can be used. Mount i...

  • Page 21

    21  if user wishes to hear audio via hdmi cable, check the box hd audio output  click the box below to select resolution. - user can select the resolution among ‘1920x1080 rb’, ‘1920x1080’, ‘1680x1050 rb’, ‘1680x1050’, ‘1280x1024’, and ‘1024x768’ - the default setting of dvr is ‘1280 x 1024’. (not...

  • Page 22

    22 use any different power supply adapter because it may cause the dvr to malfunction. Provisual fh / vh / mh series : plug the power supply adapter (dc 12v, 6.67a) which include in this product to ’dc12v’ connector and plug another side to power source. Adapter input voltage is a free volt (100 vac...

  • Page 23

    23 3. Input device and screen icons 3.1 key and leds provisual h series dvr keys ptz key operating mode setup mode ▲, ▼, ◄, ► • control pan/tilt rotation of up/down/left/right in ptz mode •up/down/left/righ t on screen cursor control 1 ~ 10 • camera select keys : (4/8 channel dvr) 11 ~ 16 • camera s...

  • Page 24

    24 provisual fh / mh / vh / aqh series dvr keys ptz key operating mode setup mode ▲, ▼, ◄, ► • control pan/tilt rotation of up/down/left/right in ptz mode •up/down/left/righ t on screen cursor control 1 ~ 16 • camera select keys : (4/8/16 channel dvr) display • select 1/4/9/16 channel display sequen...

  • Page 25

    25 3.2 camera select keys for 16 channel dvr provisual h series dvr below shows how to select camera channel for 4 channel dvr - select camera no. 1~4: press key and use 1~4 key below shows how to select camera channel for 8channel dvr - select camera no. 1~8 press key and use 1~8key below shows how...

  • Page 26

    26 8 channels dvr 16 channels dvr provisual fh / mh / vf / aqh series 4 channels dvr 8 channels dvr 16 channels dvr 3.4 using a remote controller  usage of a remote controller is same as the front panel keys.  follow the procedure below when using the remote controller for multi dvrs. ① check syst...

  • Page 27

    27 3.5 using a mouse  mouse provides an easier access to adjustment. Refer to below for proper use.  left mouse button functions the same as enter ( ) key on the front panel of dvr.  right mouse button displays the following “function keys” on screen.  click search menu at “function keys” the s...

  • Page 28

    28 3.6 screen icon icon description icon description continuous recording mode in audio recording event recording mode (alarm in/motion) 4 cms access indication/ no. Of accesses (up to 4) in recording in channel sequencing ptz registration / ptz mode lock remote controller setup in hdd overwrite mod...

  • Page 29: 4.  Setup

    29 4. Setup 4.1 login / logout  at the default setting of dvr, user has to input the password to enter the set up menu.  please press setup key to enter the setup menu and the following screen will appear.  in order to use all functions and privileges, log in as id: admin.  default password is “...

  • Page 30

    30 4.2 system 4.2.1 information  please click ( ) system>information and the following screen will appear. Site description  decide on a name of dvr.  please click ( ) keyboard icon on site description frame and the following virtual keyboard will appear.  please click ( ) desired letters (ch...

  • Page 31

    31  import: copy the menu setup stored in usb memory stick into dvr. Please plug in the memory stick and then click ( ) import.  export: store the menu setup of dvr in usb memory stick. Please plug in the memory stick and then click ( ) export.  when user is on default, import or export process...

  • Page 32

    32  user shall designate the total recording days from 1 day to 30 days and unlimited.  user may set for beeping or notifying messages that notify the used percentage of disk.  check disk overwrite and user may activate the overwrite function. - this function makes restart the recording from the ...

  • Page 33

    33  please click ( ) system>admin and the following screen will appear. Date  this menu will allow user to adjust the settings.  please follow the procedure below for time adjustment. ① click (  ) items (y, m, d) to change. A designated item will be highlighted in a box (y: year, m: month and d...

  • Page 34

    34 time format  set time indication format. Please click ( ) time format frame to select a format from the list.  when user complete date/time input, please click ( ) ntp and the following screen will appear.  this menu is for accurate setting of time of day clock in dvr.  user may check  onl...

  • Page 35

    35  clicking up and down button for checking up the status of hdd and dvd-rw devices.  using e-sata port will allow users to connect up to maximum 12 hdd +1 dvd-rw.  when user installs full storage device and dvd-rw including two e-sata storage, then following procedures will be listed as below: ...

  • Page 36

    36 hdd used in dvr. In general, it is 55°c.  click ( ) ▲, ▼ direction buttons on the right-hand side of hdd damage frame to set the permissible level of hdd damage (%). Hdd is a very crucial element for dvr recording, so set the permissible level within 1% to 2% to assure maximum safety. - while p...

  • Page 37

    37  please click ( ) new user and the following screen will appear.  click ( ) the keyboard icon on the right-hand side of user name frame and the virtual keyboard will appear. Click desired characteristics (up to 8 characteristics) on the virtual keyboard.  input password and confirm.  choose...

  • Page 38

    38  this is a screen for password resetting.  input password by clicking the keyboard icon on the right-hand side of the frame.  use key if wish to erase password on keyboard. 4.2.4 system log  please click ( ) system>system log and the following screen will appear.  system log displays divers...

  • Page 39

    39 4.2.6 shutdown  shutdown is a function to help user safely turn the dvr off. Please use the proper shut down procedure to avoid damaging to our dvr system. Do not remove the power during shut down. Caution do not turn dvr off without using the proper shut down procedure. Otherwise, it may cause ...

  • Page 40

    40 de-interlace  this function changes playback display into progressive scan or interlace scan. Check () de-interlace, then frame will display as the progressive scan and shows the better picture quality. Transparency  the transparency menu will allow user to alpha-blending of osd menu on the mo...

  • Page 41

    41  this menu will allow adjust interval of channel sequencing of spot monitor.  click ( ) spot select to choose spot monitor to be set up.  check (check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be excluded from channel sequencing.  adj...

  • Page 42

    42  the multi spot menu will allow user to adjust channel sequencing interval of spot monitor.  adjust interval for ‘full screen sequencing’.  check  check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be excluded from channel sequencing.  a...

  • Page 43

    43  users are able to set its video output resolution from 1024 x 768 to 1920 x 1080  if user wishes to hear audio via hdmi cable, check the box hd audio output  hd-sdi dvr displays and records differently with previous ntsc or pal methods.  analog output will help users to select its video outp...

  • Page 44

    44 network type  please click ( ) network type. When you click ( ) the button, it changes alternately to static (fixed ip) and dhcp (floating ip).  in static, user must manually set the static ip address for use. - set ip address, subnet mask and gateway. Please ask your network administrator fo...

  • Page 45

    45 varies every time when user access. The best alternative is ddns (dynamic domain naming system) which uses name (domain name) instead of ip address (numbers). Ddns automatically recognizes ever changing, floating ip addresses, so it will allow easy internet access.  check  a checkbox of use ddn...

  • Page 46

    46 caution it is not able to change port number during cms access to dvr. Caution if users want to use upnp feature, please note that the router has to support the upnp. Caution changes being made are applied after complete setup to exit. Caution once port numbers are changed, it must be changed the...

  • Page 47

    47  click ( ) the keyboard icon on the right-hand side of each frame on title column and the virtual keyboard will appear. Then, register titles of cameras.  if a check box is checked on no column, a video of the corresponding camera is recorded and displayed on the monitor. However, if user doe...

  • Page 48

    48 4.4.3 audio bind to cam  please click ( ) devices>audio and the following screen will appear.  the audio menu will allow user to choose whether to record audio.  when a check box is marked  on no column, corresponding audio and video are recorded. However, if the check box is not marked, aud...

  • Page 49

    49  click ( ) the keyboard icon on the right-hand side of each frame on title column and the virtual keyboard will appear. Then, please register the title of alarm output.  when a check box is marked  on no column, a corresponding alarm output starts operating. However, if user does not check th...

  • Page 50

    50  there are three kinds of recording mode. - continuous: record continuously. - event: record only when sensor or motion calls. - emergency: record when press emergency key.  the continuous menu will allow user to set recording mode.  each frame on title column shows camera title registered in ...

  • Page 51

    51 provisual dvr-400-aqh 360x 240(288) 720x240(288) 720x480(576) 1280 x 720 1920 x 1080 4 channel dvr 120(100) 120(100) 120(100) 120 100 provisual dvr-16214-aqh  hd-sdi input (ch 1~2) 360x 240(288) 720x240(288) 720x480(576) 1280 x 720 1920 x 1080 2 channel 60(50) 60(50) 60(50) 60 50 analog input (c...

  • Page 52

    52 provisual h / fh dvr series ntsc(pal) 360x240 (360x288) 720x240 (720x288) 720x480 (720x576) 4 channel dvr 120 (100) 120 (100) 60 (50) 8 channel dvr 240 (200) 120 (100) 60 (50) 16 channel dvr 480 (400) 240 (200) 120 (100) provisual mh dvr series ntsc(pal) 360x240 (360x288) 720x240 (720x288) 720x48...

  • Page 53

    53 caution if the hd-sdi input signal is 1080p, then the frame resolution of 360 x 240, 720 x 240 and 720 x 480 are decreased in half.  please click ( ) emergency and the following screen will appear emergency.  the emergency menu will allow user to set emergency videos.  each frame on title col...

  • Page 54

    54 provisual dvr-400-aqh 360x 240(288) 720x240(288) 720x480(576) 1280 x 720 1920 x 1080 4 channel dvr 120(100) 120(100) 120(100) 120 100 provisual dvr-16214-aqh  hd-sdi input (ch 1~2) 360x 240(288) 720x240(288) 720x480(576) 1280 x 720 1920 x 1080 2 channel 60(50) 60(50) 60(50) 60 50 analog input (c...

  • Page 55

    55  below lists symbols of the respective recording modes. Continuous alarm in alarm in / continuous alarm in / prealarm motion motion / continuous motion / prealarm motion / alarm in motion / alarm in / continuous motion / alarm in / prealarm  choose ‘ok’ to confirm the setting. (note) holiday (h...

  • Page 56

    56 provisual vh series dvr ntsc(pal) 360x240 (360x288) 720x240 (720x288) 720x480 (720x576) 8 channel dvr 240 (200) 240 (200) 240 (200) 16 channel dvr 480 (400) 480 (400) 480 (400) -hd-sdi type- provisual dvr-412-aqh / dvr-824-aqh / dvr-1648-aqh 360x 240(288) 720x240(288) 720x480(576) 1280 x 720 1920...

  • Page 57

    57 4.5.4 motion detection  please click ( ) record>motion detection and the following screen will appear.  the motion detection menu will allow user to set motion detection alarm.  press setup key (or right mouse button) and the setup menu will appear.  setup menu descriptions. - camera: select...

  • Page 58

    58 4.6 link  please click ( ) link and the following screen will appear.  the link menu will allow user to set recording modes of all kinds of alarms (sensor, motion event, video loss, system event, etc.), alarm output, e-mail notification and the like. 4.6.1 alarm in  please click ( ) link>ala...

  • Page 59

    59  select cameras for recording while the motion sensor is in operation and alarm outputs and set up e-mail addresses for notification.  link notification displays e-mail addresses registered in devices>network>notification.  please follow the setup procedures below. ① click (  ) motion event f...

  • Page 60

    60 4.6.4 system event  please click ( ) link>system event and the following screen will appear.  select recording cameras and alarm outputs while emergency recording using emergency key and set e-mail addresses for notification.  link notification displays e-mail addresses registered in devices>...

  • Page 61: 5.  Operation Instruction

    61 5. Operation instruction 5.1 viewing 5.1.1 first image  power on dvr and the following live video will appear, while viewing and recording at the same time.  the screen will display date/time and icons below. Icon description continuous recording mode event recording mode (alarm in/motion) in r...

  • Page 62

    62 (note) using a mouse: double click to view the corresponding camera image in full view format and click one more time to back to split screen. - split screen: please press display key and the available split screens (or multi-window view formats) will display alternately (i.E., 2x2, 3x3 and 4x4)....

  • Page 63

    63 key function ▲, ▼, , up/down/left/right rotation zoom out zoom in focus near focus far iris close iris open save preset go to the preset go to osd main menu run group tour 1~9 run pattern 1~9  to use a mouse in pan/tilt mode, please move the cursor to the lower portion near the center of the scr...

  • Page 64

    64 5.1.6 system log  press event key and the system log screen will appear.  please refer ‘setup>system>system log’ to learn different events listed on the system log and see how to delete the system log. 5.1.7 key lock  press audio>ff>forward keys in sequence to operate the key lock function. Th...

  • Page 65

    65 5.2.1 date / time search  please click ( ) date/time search in search menu and the following input box will appear.  follow the procedure below to search video by date/time. ① click (  ) the date and/or time whichever user needs to change and block the item. The designated item will be marked...

  • Page 66

    66 ⑥ click ▲ ▼ button for selecting cameras. ⑦ selected camera will show the time bar 0-60 and it will be marked on 2.5minutes basis during selected time zone. ⑧ click (  ) the box on the time indication bar to select the start time of the video playback  click ( ) search key to start playing bac...

  • Page 67

    67 device (usb memory stick, dvd-rw). - exit search: from playback display to live display. - cancel: hide menu in playback mode.  playback mode runs in the available maximum number of split screen format. To change the viewing mode, please press display key or camera select key (1~16). (note) usin...

  • Page 68

    68 5.5 digital zoom in playback  users are able to use digital zoon function in full screen playback.  drag a partition on to the screen, then the partition will enlarge as a full screen.  double click the left button of mouse to exit the zoom-in screen. 5.6 archive  the backup function will all...

  • Page 69

    69 caution please do not use the space when enter backup file name. Caution while backup procedure, please do not detach storage device or power off the dvr. Otherwise, it may cause permanent damage to the dvr or the storage device. In such case, user must reboot the dvr. If the dvr does not operate...

  • Page 70

    70 : date and time search : enter event search : showing current date & time 5.8 color control and position  please click ( ) color /alarm in search menu and the following input box will appear. (note) this function is enabled only when live mode and 1 channel mode  if user clicks (default), prop...

  • Page 71: Intuitive Cms

    71  please click ( ) color / alarm in search popup menu or in front panel and the following input box will appear.  choose ‘close’ to confirm the setting. Caution although users turn its system setting to default, the analog output will stay previous output method and not effect by the default se...

  • Page 72: Cms

    72 cms (central monitoring station) user manual this document contains preliminary information and is subject to change without notice..

  • Page 73: 6.  Program Installations

    73 6. Program installations 6.1 system recommendations  power on dvr and the following live video will appear, while viewing and recording at the same time. - processor: intel pentium(r) (at 2.8ghz or higher) - memory: 1.00gb or more - video: 128 mb agp vga card, 1024 x 768 resolution, 32-bit color...

  • Page 74

    74 ⑥ when the following screen appears, select folder and click next. ⑦ when the following screen appears, click install. ⑧ when the following screen appears, click finish to complete the installation. 6.3 login  after install cms software, cms icon below appears on desktop. Please double click on ...

  • Page 75

    75 7. Function and instructions  below lists are functions of the program. Icon icon name watch mode search mode remarks system log dvr system log ptz control dvr ptz control system health check dvr system health check dvr data playback dvr data playback cms(pc) data playback cms(pc) data playback ...

  • Page 76: 8.  Watch Mode

    76 8. Watch mode 8.1 login screen  when user login cms, the following screen will appear. This screen is of watch mode.  because it is not connected to dvr, images do not show.  please do local setting first before connecting to dvr. 8.2 local setting please click local setting button of toolbar ...

  • Page 77

    77  save option: allow user to select drive(c, d) and folder to save data.  choose ‘ok’ to confirm the setting. 8.2.2 remote site  this menu is for network setup.  make cms ip address and port coincide with dvr.  remote site connection setup - site name: input dvr site name to be displayed on t...

  • Page 78

    78 - click “scan dvr” button then ip address of dvr will be listed which is currently connected with pc in the network. - select the ip address and click “add site” then the connected dvr is automatically registered in the cms.  camera name - it helps to set the camera name in cms program other tha...

  • Page 79

    79 8.3 live video 8.3.1 network connection  as the setup is completed, user should connect cms to dvr over network. Please click in remote dvr on the screen. It will turn to blue, while being activated. Please click remote connect button.  if a popup window for id/password appears, please input id...

  • Page 80

    80  the list below describes functions of each part of the screen. 1 tool bar 2 watch mode 3 date/time led 4 site tree (dvr and channels) 5 color control bar 6 instant record button 7 system log 8 alarm out channels 9 audio channels 10 two way audio 11 video display screen 12 network connect/discon...

  • Page 81

    81 64-split screen mode: click on 64-split button and 64-split screens will display. Zoom mode: click on zoom button. Then, the setup screen will disappear and only the video image will be zoomed in (scaled to fit the screen). To cancel, please press the right mouse button. E map: load and close e m...

  • Page 82

    82 8.3.5 audio  click an audio channel to listen to the corresponding channel.  user may adjust the audio volume with a mouse.  click a mic icon to use to two ways audio. 8.3.6 system log click on log button on watch screen. This will allow user to check system log of remote site (dvr). 8.3.7 ala...

  • Page 83

    83  buttons on the screen have the following functions. ① up/down/left/right direction buttons ② up/down/left/right direction buttons ③ preset control button  click on preset control button and the following screen will appear. Please input title and preset number.  when user completes the inputt...

  • Page 84

    84 8.5 health check  this function allows user to check operating status of each unit in dvr connected to cms. Click on health check button in watch mode and the following screen will appear.  the list below describes functions of each part of the screen. 1 cms connections (up to 4) 2 camera conne...

  • Page 85

    85 8.5.3 recording status camera is in normal operation. Recording is stopped. Above the maximum number of cameras allowed. 8.5.4 motion recording status camera is in normal operation. Recording is stopped. Above the maximum number of cameras allowed. 8.5.5 alarm in connection and operating status c...

  • Page 86

    86  the setup procedure is same as that of dvr.  when the setup is completed, do not click exit button on the setup screen, but click ok or cancel button on the remote setup screen..

  • Page 87: 9.  Search Mode

    87 9. Search mode 9.1 search screen  this menu is for playing back recorded data. Click on remote search button in watch mode and the following screen mode screen will appear.  search mode provides three search functions. One is for searching dvr video by clicking remote search button and another ...

  • Page 88

    88 9.2 remote search the remote search button allows user to playback recorded video of dvr.  select date - in calendar, dates with recorded data are marked in blue. - click the wanted date among the dates marked in blue. In background of time select bar, data recorded time is displayed in bar shap...

  • Page 89

    89 9.4 event search the remote search button allows user to search event recorded data of dvr. ① designate event search start time. ② designate event search end time. ③ select camera (video) to search data. ④ check a check box (motion/alarm in/emergency/serial in) check box. ⑤ click on search index ...

  • Page 90

    90 9.5.2 print  this is for printing a selected image (within the red outline). Click image print button and the following screen will appear.  choose ‘ok’ to confirm the setting. Then, the printing proceeds. 9.5.3 save  this is for saving still image(s) in bitmap or jpeg file. Click image save b...

  • Page 91

    91 ① designate archive start time. ② designate archive end time. ③ designate file name. ④ select camera (video) to save. ⑤ click on start button to begin archive..

  • Page 92: 10.

    92 10. Others 10.1 viewer  the format of archive file is .Exe (executable file). Please double click on the icon to execute the program. Play • playback mode: 1x play pause • playback mode: pause backward • frame-by-frame backward still image playback forward • frame-by-frame forward still image pl...

  • Page 93

    93 please click on the icon to load the image file. , , , , to move the icon just drag and drop.  you can also rotate the icon. Please click on the icon and input the name of the e map file to save and execute. Please click on the icon to exit program.  please click on cms (pc) setup and select re...

  • Page 94

    94 10.3 watermark check system  mouse double click wcs.Exe program in the cms program folder (default: c:\program files\cms\wcs.Exe).  to open the check .Exe or .Jpg or .Bmp file just click load file button.  to click the check button, user will get following message; - result: - verification ok ...

  • Page 95

    95  click “file open” and choose an archived file (exe format).  click “exe to avi file” and select a directory to save the converted avi file.  select a channel to convert (only one channel can be converted at once).  select a video encoder between microsoft and divx encoder.  click “save” the...

  • Page 96: Cms Web Client

    96 cms web client cms web client user manual this document contains preliminary information and is subject to change without notice..

  • Page 97: 11.   Cms Web Client

    97 11. Cms web client 11.1 setup and login  ms explorer web browser is required for installation and using this program.  open a browser and type the ip address of dvr.  it is required to install activex in the first connection.  basically, explorer limits automatic activex installation.  click...

  • Page 98

    98 11.2 live display  after login, the following screen will appear.  the screen contains following features: ① display current live video ② setting display mode - playback: transferring search mode. - freeze: pause current display. - resume: resume paused display. - quit: finish program and close...

  • Page 99

    99 11.3 playback screen  click [playback] then following screen will appear.  the screen contains following features: ① searched playback video displays. ② transferring live mode. ③ setting date/time to search. - click a date in calendar, and then recorded data will be showed up in time bar. - sta...

  • Page 100: Cms Mobile Viewer

    100 cms mobile viewer cms mobile viewer user manual this document contains preliminary information and is subject to change without notice..

  • Page 101: 12.

    101 12. Cms mobile viewer 12.1 iphone mobile 12.1.1 system requirements  there are no other requirements to run this program because it is specialized to perform on iphone interface. 12.1.2 installation  turn on the iphone then connect to app store.  move to search menu and type “mviewer” then cl...

  • Page 102

    102  select “ ” program which is offered from dvrdomain by free.  when user clicks a “ ” button, it will be turned to “ ”  click “ ” to start installation.  if user already has an itunes account, then input user’s account to download the program.  if user does not have the account, then click “...

  • Page 103

    103  when user registered the account, the program will be automatically installed. 12.1.3 site registration  click “ ” icon on iphone menu then below will show.  move to “ ” and enter site information which are same as cms site registration.  enter site name, ip or ddns address.  enter admin/s...

  • Page 104

    104  click “ ” to save the setting. 12.1.4 connection  on “ ” window, click one of the registered site and click “ ”.  click “ ” to connect the dvr to the iphone.  to select other channels, click the channel bar below the site name.  if users wish to change the channel among 9~16, then click “ ...

  • Page 105

    105 12.1.5 search  users are able to search the recorded data in the mobile cms program.  click “ ” to use search function of the application.  click “ ” for date setting.  if users click “ ”, then the month with recorded data will show up.  choose the month that wish to search and click “ ”..

  • Page 106

    106  click “ ” to select the date in the month and click “ ”  click “ ” to select the time of the date of the recorded data.  and then search the data with the playback buttons on the search menu.  if users wish to change the search speed, then click “1x icon” to change the speed.  if the dvr i...

  • Page 107

    107  touch and drag upside on the center of the screen to zoom out.  touch and drag downside on the center of the screen to zoom in.  touch sides and corners of the screen to change the direction as user want.  touch right side of the screen to move right and left side to move left.  touch up s...

  • Page 108

    108 12.1.9 uninstallation  click the “ ” icon and hold for a while until the program icon shows x mark on the top-left side.  click the “ ” icon then it will ask to delete the program.  click “ ” button to successfully uninstall the program. 12.2 android phone 12.2.1 system requirements.

  • Page 109

    109  this program is designed and applied only for android os (version 1.6 or higher) based smart phones. 12.2.2 installation  turn on the phone then connect to android market.  move to search menu and type “mviewer” then select “ ” program which is offered from dvrdomain by free.  click “ ” the...

  • Page 110

    110  the program will be automatically installed in user’s application menu. 12.2.3 site registration  click “ ” icon on application menu then below will show.  move to “ ” tab and enter site information which is same as cms site registration.  enter site name, ip or ddns address.  enter admin/...

  • Page 111

    111  click “ ” to save the setting. 12.2.4 connection  click “ ” icon and select one of the registered site and click “ ”.  move to “ ” tab and click “ ” icon.  to change the display mode, click the “ ” and select among 1ch (full screen), 4ch, 9ch and 16ch multi view.  to select other channels,...

  • Page 112

    112 12.2.5 search  users are able to search the recorded data in the mobile cms program.  click “ ” to use search function of the application.  click “ ” to select the month, the date and the time in order. .  click “ ” to select the month, the date and the time in order.  users can adjust the ...

  • Page 113

    113  press volume down button on the right side of the phone to zoom out.  touch sides and corners of the screen to change the direction as user want.  touch right side of the screen to move right and left side to move left.  touch up side of the screen to move up and down side to move down.  i...

  • Page 114

    114  when disconnecting, please click " ” and exit the mobile viewer program. 12.2.10 uninstallation  move to setup > application > manage applications then select “ ”.  click “ ” icon then it will ask to delete the program.  click “ ” button to successfully uninstall the program. 12.3 blackberr...

  • Page 115

    115  click “search” icon and type “dvr viewer” program.  select the “dvr viewer” which is offered from dvrdomain by free and start to install the program by clicking the icon. 12.3.3 site registration  after downloading the program, click “ ” icon in the download folder or applications folder and...

  • Page 116

    116  enter site name and ip/domain.  enter admin and stream port.  enter id and password.  click “add” to save the setting. 12.3.4 connection  if the site is registered appropriately, the following screen will be shown.  click “menu>connect” to connect the site.  users can select the display ...

  • Page 117

    117 12.3.5 ptz control  users are able to control ptz by blackberry phone.  press volume up button on the right side of the phone to zoom in.  press volume down button on the right side of the phone to zoom out.  press 1~9 number buttons to change directions as user want.  for example, click no...

  • Page 118

    118 12.4 symbian mobile 12.4.1 system requirements  this program is designed and applied only for symbian os based smart phones. 12.4.2 installation  turn on the phone then connect to ovi store.  move to “search all items” and type “dvr viewer” then click “search”  select “dvr viewer “ program w...

  • Page 119

    119  when user clicks a dvr viewer icon, it will be changed to login page.  if user does not have the account, then click “create a nokia account” and it is registered by free.  type e-mail address and password and select country and type the identified text shown at the below, then you can click...

  • Page 120

    120  when users registered the account, then click “download”  when downloading has been completed, click “launch” to complete the installation. 12.4.3 site registration  click “dvr viewer” icon on symbian menu then below will show..

  • Page 121

    121  click options and select “new”.  enter the information which is similar as cms site registration.  enter site name, ip.  enter admin/stream port value.  enter id/password  click “submit” to save the setting. 12.4.4 connection  click one of the registered sites and then select “options” t...

  • Page 122

    122  choose available connection and it will start connecting the dvr to the symbian.  choose required channel to display.  selected channel will be displayed..

  • Page 123

    123 12.4.5 ptz control  users are able to control ptz with symbian by touching the screen.  touch sides and corners of the screen to change the direction as user want.  touch right side of the screen to move right and left side to move left.  touch up side of the screen to move up and down side....

  • Page 124

    124 12.4.6 information  click “options” and select “about” to check the information of the application. 12.4.7 disconnection  when disconnecting, please click “disconnect” and exit the mobile viewer program. 12.4.8 uninstallation  click “option” and select “remove” to uninstall the program.  cli...

  • Page 125

    125 12.5 windows mobile 12.5.1 system requirements  os: windows mobile professional 6.1 or higher version.  memory: 512kb or higher.  device : smartphone  network: available all wireless networking method. I.E. Wi-fi, hsdpa, wibro. 12.5.2 installation  prepare activesync program to user’s pc. -...

  • Page 126

    126  click accepting the license agreement, then click “finish” button.  installation box will appear.  click [ok] to start installation.  when installation completed, following pop-up will appear.  click [ok].  if following message appeared, it has successfully installed. (note) depending on ...

  • Page 127

    127 12.5.3 site configuration  click [add] to appear following screen.  fill in correct information. - site name: insert the name of site. - ip/domain: insert the ip address or domain name of the site. - id: input the registered id of the site. - password: input the password of the registered id. ...

  • Page 128

    128  correct items then click [save].  select a site and click [del].  confirmation message will pop up.  click [yes] then the site information will be removed. 12.5.4 connection  select a site then click [connect].  live display screen of the site will appear if it is successfully connected. ...

  • Page 129

    129  users are able to select a camera by clicking camera button.  click [disconnect] then, live display screen will be closed and site list box will appear. 12.5.5 uninstall  move to [program menu> system] then click [remove programs].  the currently installed list will show up.  choose mobile...

  • Page 130

    130 12.6 operation 12.6.1 dvr/ptz mode conversion  press system id number (for example, id: 001 press num pad ) with button.  osd will show “kbd:1” in right-bottom side that the keyboard is on dvr mode as below picture;  then, user should be able to operate the dvr functions by the keyboard contr...

  • Page 131

    131 (note) when a key does not work after set up - if the communication speed of dvr and cp are not co-related, it may not work. Please make sure the baud rate of keyboard sets on 9.6kbps. - press the button to enter ptz mode and switch to dvr mode again. - please reboot the dvr. When tx blinks cont...

  • Page 132: Serial In (Pos / Atm)

    132 serial in (pos / atm) serial in (pos / atm) user manual.

  • Page 133

    133 this document contains preliminary information and is subject to change without notice. 13. Serial in (pos/atm) 13.1 usage of serial-in function  enables to record/search/display all transactions on monitoring screen by connecting pos/atm/cash register.  user can choose the data whether to rec...

  • Page 134

    134 13.4 link 13.4.1 link setup  click “setup>link>” then shows as below. (note) the above menu is only available on the dvr model with serial-in function.  click “serial in” to appear following screen.  select pos/atm port by clicking ‘serial in’ button.  assign the port to display/record chann...

  • Page 135

    135  tick the box ( □) item alarm in.  click the time/date that wishes to activate atm/pos function on schedule.  it is possible to activate all the time by clicking top-right side of table.  click “ok” to save the schedules. (note) please do not select the alarm in and motion simultaneously on ...

  • Page 136

    136 13.5.3 osd display  osd items are to decide whether to display the information from the serial port connected to the rs232 port on osd screen.  they have 4 menus as followings: - none: displays anything on the osd screen. - live: displays incoming information from the serial port in real time ...

  • Page 137

    137  input a certain repeated string to “line delimiter”.  decide the number of minimum characters in “mcpl” item to hide data under the designated number of characters.  input the pattern of dummy data to discard pattern.  choose the data which willing to display and enter the start pattern and...

  • Page 138

    138  then tick the auto box off in order to make the dvr recognizes the data between the start and end patterns.  finally, test again and adjust data to remove missed dummy data. 13.6 search  using event search function.  please click ( ) the “search>event search” menu on the pop-up menu of the...