1. DL manuals
  2. Proxim
  3. Wireless Access Point
  4. ORiNOCO AP-4000
  5. User Manual

Proxim ORiNOCO AP-4000 User Manual

Summary of ORiNOCO AP-4000

  • Page 1

    Orinoco ap-4000, ap-4000m and ap-4900m user guide.

  • Page 2

    Ap-4000/4000m/4900m user guide 2 copyright © 2006 proxim wireless corporation. All rights reserved. Covered by one or more of the following u.S. Patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This user guide and the software described in it are copyrighted with all rights...

  • Page 3: Contents

    Ap-4000/4000m/4900m user guide 3 contents 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 products covered in this user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 4

    Ap-4000/4000m/4900m user guide 4 dynamic dns support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Ap-4000/4000m/4900m user guide 5 radius accounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 ssid/vlan/security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 6

    Ap-4000/4000m/4900m user guide 6 vlan operation issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 power-over-ethernet (poe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 7

    Ap-4000/4000m/4900m user guide 7 security parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 vlan/ssid parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 8: Introduction

    8 ap-4000/4000m/4900m user guide 1 introduction this chapter contains information on the following: • products covered in this user guide • introduction to wireless networking • mesh networking • guidelines for roaming • management and monitoring capabilities products covered in this user guide this...

  • Page 9

    Introduction ap-4000/4000m/4900m user guide introduction to wireless networking 9 figure 1-1 typical wireless network access infrastructure.

  • Page 10

    Introduction ap-4000/4000m/4900m user guide mesh networking 10 mesh networking using the orinoco mesh creation protocol (omcp), the ap-4000/4000m/4900m supports structured mesh networking. In a mesh network, access points use their wireless interface as a backhaul to the rest of the network. Access ...

  • Page 11

    Introduction ap-4000/4000m/4900m user guide mesh networking 11 are discovered, map2 through map8 will build a neighbor table from the beacons and probe responses they receive. The neighbor table contains three kinds of links: • active: link with a mesh neighbor that has gone through association and ...

  • Page 12

    Introduction ap-4000/4000m/4900m user guide mesh networking 12 after a short while, the network in this example will look like figure 1-4 , where solid lines indicate active mesh links and dotted lines indicate established but inactive mesh links. Figure 1-4 mesh startup topology example – step 3 in...

  • Page 13

    Introduction ap-4000/4000m/4900m user guide guidelines for roaming 13 – average utilization (time that a client is actually transferring data) is 10%. If the conditions on your network are different than the assumptions above, then the maximum number of aps should be adjusted accordingly. Note: clie...

  • Page 14

    Introduction ap-4000/4000m/4900m user guide management and monitoring capabilities 14 • http/https interface • command line interface • snmp management • ssh (secure shell) management http/https interface the http interface (web browser interface) provides easy access to configuration settings and n...

  • Page 15

    Introduction ap-4000/4000m/4900m user guide management and monitoring capabilities 15 enterprise mib for more information; the mib can be opened with any text editor, such as microsoft word, notepad, or wordpad. Snmpv3 secure management snmpv3 is based on the existing snmp framework, but addresses s...

  • Page 16

    16 ap-4000/4000m/4900m user guide 2 installation and initialization in this chapter: • ap-4000/4000m/4900m hardware description – overview – led indicators – power-over-ethernet (poe) – antennas • prerequisites – general prerequisites – mesh prerequisites • system requirements • product package • ha...

  • Page 17

    Installation and initialization ap-4000/4000m/4900m user guide ap-4000/4000m/4900m hardware description 17 ap-4000/4000m/4900m hardware description overview the ap-4000 and ap-4000m are tri-mode aps equipped with the following embedded radios: • one embedded 802.11a radio and one embedded 802.11b/g ...

  • Page 18

    Installation and initialization ap-4000/4000m/4900m user guide ap-4000/4000m/4900m hardware description 18 figure 2-2 led indicators on the ap-4000/4000m/4900m top panel power-over-ethernet (poe) the ap-4000/4000m/4900m is equipped with an 802.3af-compliant power-over-ethernet (poe) module. Poe deli...

  • Page 19

    Installation and initialization ap-4000/4000m/4900m user guide ap-4000/4000m/4900m hardware description 19 external antennas the ap-4000/4000m/4900m also has four antenna connectors, two on each radio, for use with external antennas. External antennas can be used with either radio on the ap-4000/400...

  • Page 20

    Installation and initialization ap-4000/4000m/4900m user guide ap-4000/4000m/4900m hardware description 20 4.9 ghz antenna on the ap-4900m, antenna connector 3 is equipped with a pigtail adaptor for connection to a 4.9 ghz antenna. When the ap-4900m is configured to operate in the 4.9 ghz public saf...

  • Page 21

    Installation and initialization ap-4000/4000m/4900m user guide prerequisites 21 prerequisites general prerequisites before installing your unit, you need to gather certain network information. The following table identifies the information you need. Network name (ssid of the wireless cards) you must...

  • Page 22

    Installation and initialization ap-4000/4000m/4900m user guide system requirements 22 mesh prerequisites before setting up a mesh network, gather the following information: system requirements to begin using an ap, you must have the following minimum requirements: • a 10base-t ethernet or 100base-tx...

  • Page 23

    Installation and initialization ap-4000/4000m/4900m user guide product package 23 product package each ap-4000/4000m/4900m shipment includes the items in the following table. Verify that you have received all parts of the shipment. Note: unless noted in this table, cables are not supplied with the u...

  • Page 24

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 24 hardware installation perform the following procedures to install the ap hardware: • attach cables • install the security cover (optional) • mount the ap-4000/4000m/4900m • power on the unit attach cables cabling...

  • Page 25

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 25 • use a cross-over ethernet cable or adapter if you intend to connect the unit to a single computer. 3. Optionally, connect an rs-232 cable (not shown) to the rs-232 console port (the right port, labeled “rs-232”...

  • Page 26

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 26 2. Slide the hinging end of the security cover into the hole on the rear panel of the unit to the left of the connectors. Once in place, pivot the right side of the cover to bring it close to the rear panel of th...

  • Page 27

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 27 3. Fasten the mounting plate with two screws through the circular holes of the plate. Depending on the type of wall, you may need to use the two fasteners provided. 4. Holding the unit so that the connectors on t...

  • Page 28

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 28 when the unit is powered on, it performs startup diagnostics. When startup is completed, the leds show the operational state of the unit. The led indicators exhibit the following behavior: install external antenn...

  • Page 29

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 29 figure 2-4 opening the antenna compartment 2. There are four antenna connectors in the ap-4000/4000m/4900m, labeled 1 through 4. Connectors 1 and 2 are for the 802.11b/g radio, and connectors 3 and 4 and for the ...

  • Page 30

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 30 connecting antenna(s) to the ap-4900m for 4.9 ghz operation to attach an external antenna to the ap-4900m, attach the selected antenna to the pigtail attachment connected to the ap’s antenna connector 3 (see figu...

  • Page 31

    Installation and initialization ap-4000/4000m/4900m user guide hardware installation 31 antenna types and maximum gain for devices using external antennas, professional installers should select only the antenna types listed in the following table, with gain not exceeding the listed maximum gain for ...

  • Page 32

    Installation and initialization ap-4000/4000m/4900m user guide initialization 32 initialization the following sections detail how to initialize the ap using scantool, log in to the http interface, perform an initial configuration of the ap using the setup wizard, and download the required ap softwar...

  • Page 33

    Installation and initialization ap-4000/4000m/4900m user guide initialization 33 note: if your access point does not appear in the scan list, click the rescan button to update the display. If the unit still does not appear in the list, see troubleshooting for suggestions. Note that after rebooting a...

  • Page 34

    Installation and initialization ap-4000/4000m/4900m user guide initialization 34 k. Click the change button to return to the change screen. L. Click the web configuration button at the bottom of the change screen. M. Proceed to the logging in section for information on how to access the http interfa...

  • Page 35

    Installation and initialization ap-4000/4000m/4900m user guide initialization 35 figure 2-10 system status screen the buttons on the left of the screen provide access to the monitoring and configuration options for the ap. See advanced configuration to begin configuring the ap manually. You can also...

  • Page 36

    Installation and initialization ap-4000/4000m/4900m user guide initialization 36 • save & next button: each setup wizard screen has a save & next button. Click this button to submit any changes you made to the unit’s parameters and continue to the next page. The instructions below describe how to na...

  • Page 37

    Installation and initialization ap-4000/4000m/4900m user guide initialization 37 — primary network name (ssid): enter a network name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Note that the unit supports up to 16 ssi...

  • Page 38

    Installation and initialization ap-4000/4000m/4900m user guide initialization 38 2. If prompted, create an account to gain access. Note: the knowledgebase is available to all website visitors. First-time users will be asked to create an account to gain access. 3. Click search knowledgebase. 4. In th...

  • Page 39

    Installation and initialization ap-4000/4000m/4900m user guide initialization 39 figure 2-13 warning message 5. Click ok to continue with the operation or cancel to abort the operation. 6. If the operation is unsuccessful, you will receive an error message. If this occurs, see the troubleshooting ch...

  • Page 40

    Installation and initialization ap-4000/4000m/4900m user guide initialization 40 4. Enter the ip address of your tftp server in the field provided. 5. Enter the file name (including the file extension). If the file is located in the default tftp directory, you need enter only the file name. Otherwis...

  • Page 41: System Status

    41 ap-4000/4000m/4900m user guide 3 system status the first screen displayed after logging in is the system status screen. You can always return to this screen by clicking the status button. Figure 3-1 system status screen the system status screen provides the following information: • system status:...

  • Page 42: Advanced Configuration

    42 ap-4000/4000m/4900m user guide 4 advanced configuration this chapter contains information on configuring settings in the following categories: • system : configure specific system information such as system name and contact information. • network: configure ip, dns client, dhcp server, dhcp relay...

  • Page 43

    Advanced configuration ap-4000/4000m/4900m user guide 43 figure 4-1 configure main screen 2. Click the tab that corresponds to the parameter you want to configure. For example, click network to configure the access point’s tcp/ip settings. Each configure tab is described in the remainder of this cha...

  • Page 44

    Advanced configuration ap-4000/4000m/4900m user guide system 44 system you can configure and view the following parameters within the system configuration screen: • name: the name assigned to the ap. See the dynamic dns support and access point system naming convention sections for rules on naming t...

  • Page 45

    Advanced configuration ap-4000/4000m/4900m user guide system 45 figure 4-2 system tab dynamic dns support dns is a distributed database mapping the user readable names and ip addresses (and more) of every registered system on the internet. Dynamic dns is a lightweight mechanism which allows for modi...

  • Page 46

    Advanced configuration ap-4000/4000m/4900m user guide network 46 network the network tab contains the following sub-tabs: • ip configuration • dhcp server • dhcp relay agent • link integrity • sntp (simple network time protocol) ip configuration this tab is used to configure the internet (tcp/ip) se...

  • Page 47

    Advanced configuration ap-4000/4000m/4900m user guide network 47 basic ip parameters • ip address assignment type: set this parameter to dynamic to configure the access point as a dynamic host configuration protocol (dhcp) client; the access point will obtain ip settings from a network dhcp server a...

  • Page 48

    Advanced configuration ap-4000/4000m/4900m user guide network 48 figure 4-4 dhcp server configuration screen you can configure and view the following parameters within the dhcp server configuration screen: note: you must reboot the ap before changes to any of these dhcp server parameters take effect...

  • Page 49

    Advanced configuration ap-4000/4000m/4900m user guide network 49 note: the default lease time cannot be larger than the maximum lease time. If you set the maximum lease time, you should also set the default lease time to ensure that the default lease time is less than the maximum. – comment (optiona...

  • Page 50

    Advanced configuration ap-4000/4000m/4900m user guide network 50 dhcp server ip address table the ap supports the configuration of a maximum of 10 server settings in the dhcp relay agents server table. At least one server must be configured to enable dhcp relay. To add entries to the table of dhcp r...

  • Page 51

    Advanced configuration ap-4000/4000m/4900m user guide network 51 figure 4-7 link integrity configuration screen sntp (simple network time protocol) sntp allows a network entity to communicate with time servers in the network/internet to retrieve and synchronize time of day information. When this fea...

  • Page 52

    Advanced configuration ap-4000/4000m/4900m user guide network 52 figure 4-8 sntp configuration screen you can configure and view the following parameters within the sntp screen: • sntp status: select enable or disable from the drop-down menu. The selected status will determine which of the parameter...

  • Page 53

    Advanced configuration ap-4000/4000m/4900m user guide network 53 – year: enter the current year. – month: enter the month in digits (1-12). – day: enter the day in digits (1-31). – hour: enter the hour in digits (0-23). – minutes: enter the minutes in digits (0-59). – seconds: enter the seconds in d...

  • Page 54

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 54 interfaces from the interfaces tab, you configure the access point’s operational mode settings, power control settings, wireless interface settings and ethernet settings. You may also configure a wireless distribution system for ap-...

  • Page 55

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 55 figure 4-10 operational mode screen (ap-4900m) the wireless-a interface operates in 802.11a mode on the ap-4000/4000m and in either 802.11a mode or 4.9 ghz public safety mode on the ap-4900m. In 4.9 ghz public safety mode, you must ...

  • Page 56

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 56 super mode and turbo mode super mode improves throughput between the access point and wireless clients that support this capability. For wireless clients that support this capability the ap will negotiate and treat them accordingly,...

  • Page 57

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 57 4. Click ok. 5. Configure transmit power control and transmit power level if required. Transmit power control/transmit power level transmit power control uses standard 802.11d frames to control transmit power within an infrastructur...

  • Page 58

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 58 wireless-a (802.11a/4.9 ghz radio) and wireless-b (802.11b/g radio) figure 4-11 wireless interface a.

  • Page 59

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 59 you can view and configure the following parameters for the wireless-a and wireless-b interfaces: note: you must reboot the access point before any changes to these parameters take effect. • physical interface type: for wireless int...

  • Page 60

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 60 – for 802.11b/g -- auto fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 mbits/sec – for 802.11g-wifi -- auto fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 mbits/sec note: 802.11g-wifi has been defined for wi-fi testing...

  • Page 61

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 61 affected countries japan is certified in the telec regulatory domain for operation in the 5 ghz band. The following countries are certified in the etsi regulatory domain for operation in the 5 ghz band: rts/cts medium reservation th...

  • Page 62

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 62 • enable the transmission and reception of frames on that wireless interface • enable the associated bss port on that interface • start the ap services to wireless clients • indicate the wireless service resume status of the wireles...

  • Page 63

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 63 figure 4-13 channel blacklist table - edit screen note: wireless service can be shut down/resumed on each wireless interface individually. Wireless distribution system (wds) a wireless distribution system (wds) creates a link betwee...

  • Page 64

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 64 bridging wds each wds link is mapped to a logical wds port on the ap. Wds ports behave like ethernet ports rather than like standard wireless interfaces: on a bss port, an access point learns by association and from frames; on a wds...

  • Page 65

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 65 figure 4-15 wds configuration 5. Click the edit button to update the wireless distribution system (wds) table. Figure 4-16 adding wds links.

  • Page 66

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 66 6. Select which encryption method to use (if any) from the wds security mode drop-down menu. 7. If you selected a wds security mode, do one of the following: • if you selected wep: enter an encryption key. • if you selected aes: ent...

  • Page 67

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 67 mesh mesh functionality can be enabled on only one of the ap’s wireless interfaces. When configured for mesh, the ap’s wireless interface simultaneously functions as a mesh link and as a radio to service clients. Caution: mesh mis-c...

  • Page 68

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 68 • mesh radio: select the wireless interface on which to enable mesh functionality. Select wireless interlace a (802.11a/4.9 ghz radio) or wireless interface b (802.11b/g radio). • mesh ssid: enter a unique mesh network name (ssid) b...

  • Page 69

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 69 click on the advanced button on the interfaces > mesh page to access advanced mesh parameters. The parameters on the advanced mesh parameters page are preconfigured with default settings that optimize the type of network identified ...

  • Page 70

    Advanced configuration ap-4000/4000m/4900m user guide interfaces 70 note: when enabling auto switch mode, proxim recommends that you also enable auto channel select. Acs is is configured on the wireless a or wireless b page. See wireless-a (802.11a/4.9 ghz radio) and wireless-b (802.11b/g radio) for...

  • Page 71

    Advanced configuration ap-4000/4000m/4900m user guide management 71 management the management tab contains the following sub-tabs: • passwords • ip access table • services • automatic configuration (autoconfig) • hardware configuration reset (chrd) passwords passwords are stored in flash memory and ...

  • Page 72

    Advanced configuration ap-4000/4000m/4900m user guide management 72 ip access table the management ip access table limits in-band management access to the ip addresses or range of ip addresses specified in the table. This feature applies to all management services (snmp, http, and cli) except for cl...

  • Page 73

    Advanced configuration ap-4000/4000m/4900m user guide management 73 • secure management status: enables the further configuration of https access, snmpv3, and secure shell (ssh). After enabling secure management, you can choose to configure https (ssl) and secure shell access on the services tab, an...

  • Page 74

    Advanced configuration ap-4000/4000m/4900m user guide management 74 figure 4-20 management services configuration screen.

  • Page 75

    Advanced configuration ap-4000/4000m/4900m user guide management 75 telnet configuration settings • telnet interface bitmask: select the interface (ethernet, wireless-slot a, wireless-slot b, all interfaces) from which you can manage the ap via telnet. This parameter can also be used to disable teln...

  • Page 76

    Advanced configuration ap-4000/4000m/4900m user guide management 76 note: when secure management is enabled on the ap, ssh will be enabled by default and cannot be disabled. Host keys must either be generated externally and uploaded to the ap (see uploading externally generated host keys ), generate...

  • Page 77

    Advanced configuration ap-4000/4000m/4900m user guide management 77 serial configuration settings the serial port interface on the ap is enabled at all times. See setting ip address using serial port for information on how to access the cli interface via the serial port. You can configure and view t...

  • Page 78

    Advanced configuration ap-4000/4000m/4900m user guide management 78 • radius profile for management access control: specifies the radius profile to be used for radius based management access. • local user status: enables or disables the local user when radius based management is enabled. The default...

  • Page 79

    Advanced configuration ap-4000/4000m/4900m user guide management 79 figure 4-22 automatic configuration screen set up automatic configuration for dynamic ip perform the following procedure to enable and set up automatic configuration when you have a dynamic ip address for the tftp server via dhcp. T...

  • Page 80

    Advanced configuration ap-4000/4000m/4900m user guide management 80 figure 4-23 dhcp options: setting the boot server host name 4. Add the boot server hostname and boot filename parameters to the available options list. 5. Set the value of the boot server hostname parameter to the hostname or ip add...

  • Page 81

    Advanced configuration ap-4000/4000m/4900m user guide management 81 access to the ap is not protected, an unauthorized person could reset the ap to factory defaults and thus gain control of the ap. The user can disable the hardware configuration reset functionality to prevent unauthorized access. Th...

  • Page 82

    Advanced configuration ap-4000/4000m/4900m user guide management 82 2. Check (enable) or uncheck (disable) the enable hardware configuration reset checkbox. 3. Change the default configuration reset password in the “configuration reset password” and “confirm” fields. 4. Click ok. 5. Reboot the ap. N...

  • Page 83

    Advanced configuration ap-4000/4000m/4900m user guide filtering 83 filtering the access point’s packet filtering features help control the amount of traffic exchanged between the wired and wireless networks. There are four sub-tabs under the filtering heading: • ethernet protocol • static mac • adva...

  • Page 84

    Advanced configuration ap-4000/4000m/4900m user guide filtering 84 • to add an entry, click add, and then specify the protocol number and a protocol name. – protocol number: enter the protocol number. See http://www.Iana.Org/assignments/ethernet-numbers for a list of protocol numbers. – protocol nam...

  • Page 85

    Advanced configuration ap-4000/4000m/4900m user guide filtering 85 figure 4-29 static mac filter configuration each static mac entry contains the following fields: • wired mac address • wired mask • wireless mac address • wireless mask • comment: this field is optional. Each mac address or mask is c...

  • Page 86

    Advanced configuration ap-4000/4000m/4900m user guide filtering 86 a maximum of 200 entries can be created in the static mac filter table. To create an entry, click add and enter the appropriate mac addresses and masks to setup a filter. The entry is enabled automatically when saved. Figure 4-30 sta...

  • Page 87

    Advanced configuration ap-4000/4000m/4900m user guide filtering 87 prevent all wireless devices from communicating with a single wired device configure the following settings to prevent all three wireless clients from communicating with wired server 1: • wired mac address: 00:40:f4:1c:db:6a • wired ...

  • Page 88

    Advanced configuration ap-4000/4000m/4900m user guide filtering 88 figure 4-31 advanced filter configuration the following protocols are listed in the advanced filter table: • deny ipx rip • deny ipx sap • deny ipx lsp • deny ip broadcasts • deny ip multicasts the ap can filter these protocols in th...

  • Page 89

    Advanced configuration ap-4000/4000m/4900m user guide filtering 89 figure 4-32 static mac filter table - edit entries tcp/udp port port-based filtering enables you to control wireless user access to network services by selectively blocking tcp/udp protocols through the ap. A user specifies a protoco...

  • Page 90

    Advanced configuration ap-4000/4000m/4900m user guide filtering 90 figure 4-33 tcp/udp port filter configuration 2. Click add under the tcp/udp port filter table heading. 3. In the tcp/udp port filter table , enter the protocol names to filter. 4. Set the destination port number (a value between 1 a...

  • Page 91

    Advanced configuration ap-4000/4000m/4900m user guide filtering 91 figure 4-34 tcp/udp port filter table - add entries editing tcp/udp port filters 1. Click edit under the tcp/udp port filter table heading. 2. Make any changes to the protocol name or port number for a specific entry, if necessary. 3...

  • Page 92

    Advanced configuration ap-4000/4000m/4900m user guide alarms 92 alarms the alarms tab has the following sub-tabs: • groups • alarm host table • syslog • rogue scan groups alarm groups can be enabled or disabled via the web interface. Place a check mark in the box provided to enable a specific group....

  • Page 93

    Advanced configuration ap-4000/4000m/4900m user guide alarms 93 wireless interface/card trap group operational trap group oritrapauthenticationfailure client authentication failure has occurred. Authentication failures can range from: • mac access control table • radius mac authentication • 802.1x a...

  • Page 94

    Advanced configuration ap-4000/4000m/4900m user guide alarms 94 flash memory trap group tftp trap group image trap group oritrapdhcpfailed response to the dhcp client request not received; device not dynamically assigned an ip address major oritrapdnsclientlookupfailure dns client attempts to resolv...

  • Page 95

    Advanced configuration ap-4000/4000m/4900m user guide alarms 95 sntp trap group generic trap group a generic snmp trap may be sent for any of the following reasons: system feature/license group in addition, the ap supports these standard traps, which are always enabled: rfc 1215-trap bridge mib (rfc...

  • Page 96

    Advanced configuration ap-4000/4000m/4900m user guide alarms 96 all these alarm groups correspond to system alarms that are displayed in the system status screen , including the traps that are sent by the ap to the snmp managers specified in the alarm host table . Alarm host table to add an entry an...

  • Page 97

    Advanced configuration ap-4000/4000m/4900m user guide alarms 97 syslog the syslog messaging system enables the ap to transmit event messages to a central server for monitoring and troubleshooting. The access point logs “session start (log-in)” and “session stop (log-out)” events for each wireless cl...

  • Page 98

    Advanced configuration ap-4000/4000m/4900m user guide alarms 98 • syslog lowest priority logged: the ap will send event messages to the syslog server that correspond to the selected priority number and any priority numbers below it. For example, if set to 6, the ap will transmit event messages label...

  • Page 99

    Advanced configuration ap-4000/4000m/4900m user guide alarms 99 client login authentication status 6 informational client logs in/authenticates. Message includes: • client mac address • authentication type = none, acl, radius mac, 802.1x • cipher type = none, wep, tkip, aes • status = allow, deny • ...

  • Page 100

    Advanced configuration ap-4000/4000m/4900m user guide alarms 100 rogue scan the rogue scan feature provides an additional security level for wireless lan deployments. Rogue scan uses the selected wireless interface(s) for scanning its coverage area for access points and clients. A centralized networ...

  • Page 101

    Advanced configuration ap-4000/4000m/4900m user guide alarms 101 figure 4-37 preventing rogue ap attacks the figure above shows client 1 connected to a trusted ap and client 2 connected to a rogue ap. The trusted ap scans the networks, detects client 2, and notifies the network manager. The network ...

  • Page 102

    Advanced configuration ap-4000/4000m/4900m user guide alarms 102 rogue scan data collection the ap stores information gathered about detected stations during scanning in a rogue scan result table. The rogue scan result table can store a maximum of 2000 entries. When the table fills, the oldest entry...

  • Page 103

    Advanced configuration ap-4000/4000m/4900m user guide alarms 103 • notify all (notify both ap and client detection) 8. Configure the scan results trap report style to control the way detected stations are reported in the notification: • report all detected stations since last scan (default) • report...

  • Page 104

    Advanced configuration ap-4000/4000m/4900m user guide bridge 104 bridge the ap is a bridge between your wired and wireless networking devices. As a bridge, the functions performed by the ap include: • mac address learning • forward and filtering decision making • spanning tree protocol used for loop...

  • Page 105

    Advanced configuration ap-4000/4000m/4900m user guide bridge 105 figure 4-39 spanning tree sub-tab storm threshold storm threshold is an advanced bridge setup option that you can use to protect the network against data overload by: • specifying a maximum number of frames per second as received from ...

  • Page 106

    Advanced configuration ap-4000/4000m/4900m user guide bridge 106 • wireless threshold: enter the maximum allowed number of packets per second. Intra bss the wireless clients (or subscribers) that associate with a certain ap form the basic service set (bss) of a network infrastructure. By default, wi...

  • Page 107

    Advanced configuration ap-4000/4000m/4900m user guide qos 107 qos wi-fi multimedia (wmm)/quality of service (qos) introduction the ap supports wi-fi multimedia (wmm), which is a solution for qos functionality based on the ieee 802.11e specification. Wmm defines enhancements to the mac for wireless l...

  • Page 108

    Advanced configuration ap-4000/4000m/4900m user guide qos 108 2. To enable qos, check the enable quality of service checkbox. 3. Configure the qos maximum medium threshold for all admission controls. Admission will be granted if the new requested traffic stream and already admitted time is less than...

  • Page 109

    Advanced configuration ap-4000/4000m/4900m user guide qos 109 8. Select whether to enable qos marking. 9. Click ok. Priority mapping use this page to configure qos 802.1p to 802.1d priority mappings (for layer 2 policies) and ip dscp to 802.1d priority mappings (for layer 3 policies). The first entr...

  • Page 110

    Advanced configuration ap-4000/4000m/4900m user guide qos 110 figure 4-43 add priority mapping entry 3. Select the 802.1p priority (from 0-7) for 802.1d priorities 0-7. 4. Click ok. 5. Click add in the ip precedence/dscp ranges and 802.1d priority table. 6. Select the ip dscp range for each 802.1d p...

  • Page 111

    Advanced configuration ap-4000/4000m/4900m user guide qos 111 perform the following procedure to configure the station and ap edca tables. 1. Click configure > qos > edca. Figure 4-44 edca tables 2. Click edit and configure the following parameters in each table:.

  • Page 112

    Advanced configuration ap-4000/4000m/4900m user guide qos 112 note: changes to edca parameters require a reboot of the ap to take effect. • index: read-only. Indicates the index of the access category (1-4) being defined: – 1 = best effort – 2 = background – 3 = video – 4 = voice • cwmin: minimum co...

  • Page 113

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 113 radius profiles configuring radius profiles on the ap allows the administrator to define a profile for radius servers used by the system or by a vlan. The network administrator can define radius servers per authentication mode...

  • Page 114

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 114 this figure shows a network with separate authentication servers for each authentication type and for each vlan. The clients in vlan 1 are authenticated using the authentication servers configured for vlan 1. The type of authe...

  • Page 115

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 115 note: this page configures only the primary radius server associated with the profile. After configuring these parameters, save them by clicking ok. Then, to configure the secondary radius server, edit the profile from the mai...

  • Page 116

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 116 – colon delimited/mac: mac addresses are formatted with a colon between each pair of digits (xx:yy:zz:aa:bb:cc) and the password sent to the radius server is the mac address of the client. – single dash delimited/mac: mac addr...

  • Page 117

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 117 radius accounting using an external radius server, the ap can track and record the length of client sessions on the access point by sending radius accounting messages per rfc2866. When a wireless client is successfully authent...

  • Page 118

    Advanced configuration ap-4000/4000m/4900m user guide radius profiles 118 – obtained during the authentication process and used for determining the time interval for sending accounting update messages. – this attribute value takes precedence over the value of the accounting update interval. Accounti...

  • Page 119

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 119 ssid/vlan/security the ap provides several security features to protect your network from unauthorized access. This section gives an overview of vlans and then discusses the ssid/vlan/security configuration options in the a...

  • Page 120

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 120 figure 4-48 components of a typical vlan vlan workgroups and traffic management access points that are not vlan-capable typically transmit broadcast and multicast traffic to all wireless network interface cards (nics). This...

  • Page 121

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 121 1. Vlan disabled: your network does not use vlans, and you cannot configure the ap to use multiple ssids. 2. Vlan enabled, each vlan workgroup uses a different vlan id tag. 3. Vlan enabled, a mixture of tagged and untagged ...

  • Page 122

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 122 caution: once a vlan management id is configured and is equivalent to one of the vlan user ids on the ap, all members of that user vlan will have management access to the ap. Be careful to restrict vlan membership to those ...

  • Page 123

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 123 • eap-message digest 5 (md5): username/password-based authentication; does not support automatic key distribution • eap-transport layer security (tls): certificate-based authentication (a certificate is required on the serv...

  • Page 124

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 124 wi-fi protected access (wpa/802.11i [wpa2]) wi-fi protected access (wpa) is a security standard designed by the wi-fi alliance in conjunction with the institute of electrical and electronics engineers (ieee). The ap support...

  • Page 125

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 125 if you have both 802.1x and mac access control authentication enabled, the 802.1x authentication takes precedence because it is higher in the authentication protocol hierarchy. This is required in order to propagate the wep...

  • Page 126

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 126 figure 4-51 security profile configuration 2. Click add in the security profile table to create a new entry. To modify an existing profile, select the profile and click edit. To delete an existing profile, select the profil...

  • Page 127

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 127 — for 64-bit encryption, an encryption key is 10 hexadecimal characters (0-9 and a-f) or 5 ascii characters (see ascii character chart ). — for 128-bit encryption, an encryption key is 26 hexadecimal characters or 13 ascii ...

  • Page 128

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 128 figure 4-52 security profile table - add entries.

  • Page 129

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 129 mac access the mac access sub-tab allows you to build a list of stations, identified by their mac addresses, authorized to access the network through the ap. The list is stored inside each ap within your network. Note that ...

  • Page 130

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 130 wireless-a or wireless-b each ssid can have its own security profile that defines its security mode, authentication mechanism, and encryption, so that customers can have multiple types of clients (non-wep, wep, 802.1x, wpa,...

  • Page 131

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 131 • enable: mac addresses in the mac access control list stored on the radius server are blocked or allowed, based on the mac acl settings. If a higher priority authentication protocol is also enabled, the higher-priority set...

  • Page 132

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 132 figure 4-55 ssid/vlan edit entries screen (vlan tagging disabled) 9. Enter a unique network name (ssid) between 1 and 32 characters. This parameter is mandatory. Note: do not use quotation marks (single or double) in the ne...

  • Page 133

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 133 configured, then three ssids will be broadcast in individual beacons; the fourth and subsequent ssids will be combined in one beacon and will not be broadcast. If closed system is set to enable, the ssid will not be broadca...

  • Page 134

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 134 note: if you disable (uncheck) the enable security per ssid option, you will be able to add multiple ssid/vlans, but the same configuration parameters (described below) will applied to all of them. 3. Click add to configure...

  • Page 135

    Advanced configuration ap-4000/4000m/4900m user guide ssid/vlan/security 135 • you can set the vlan id to “-1” or “untagged” if you do not want clients that are using a specific ssid to be members of a vlan workgroup. Only one “untagged” vlan id is allowed per interface. • the vlan id must match an ...

  • Page 136: Monitoring

    136 ap-4000/4000m/4900m user guide 5 monitoring this chapter discusses the following monitoring options: • version: provides version information for the access point’s system components. • icmp: displays statistics for internet control message protocol packets sent and received by the ap. • ip/arp t...

  • Page 137

    Monitoring ap-4000/4000m/4900m user guide version 137 version from the http interface, click the monitor button and select the version tab. The list displayed provides you with information that may be pertinent when calling technical support. With this information, your technical support representat...

  • Page 138

    Monitoring ap-4000/4000m/4900m user guide icmp 138 icmp this tab provides statistical information for both received and transmitted messages directed to the ap. Not all icmp traffic on the network is counted in the icmp (internet control message protocol) statistics. Figure 5-3 icmp monitoring tab.

  • Page 139

    Monitoring ap-4000/4000m/4900m user guide ip/arp table 139 ip/arp table this tab provides information based on the address resolution protocol (arp), which relates mac address and ip addresses. Figure 5-4 ip/arp table monitoring tab.

  • Page 140

    Monitoring ap-4000/4000m/4900m user guide learn table 140 learn table this tab displays information relating to network bridging. It reports the mac address for each node that the device has learned is on the network and the interface on which the node was detected. There can be up 10,000 entries in...

  • Page 141

    Monitoring ap-4000/4000m/4900m user guide iapp 141 iapp this tab displays statistics relating to client handovers and communications between orinoco access points. Figure 5-6 iapp monitoring tab.

  • Page 142

    Monitoring ap-4000/4000m/4900m user guide radius 142 radius this tab provides radius authentication, eap/802.1x authentication, and accounting information for both the primary and backup radius servers for each radius server profile. Note: separate radius servers can be configured for each radius se...

  • Page 143

    Monitoring ap-4000/4000m/4900m user guide interfaces 143 interfaces this tab displays statistics for the ethernet and wireless interfaces. Figure 5-8 interface monitoring tab (ethernet) description of interface statistics the following statistics are displayed for the ethernet interface only, either...

  • Page 144

    Monitoring ap-4000/4000m/4900m user guide interfaces 144 • ethernet chipset (ethernet): identifies the chipset used to realize the interface. • excessive collisions (ethernet): the number of frames for which transmission fails due to excessive collisions. • failed ack count (wireless-slot a/b): the ...

  • Page 145

    Monitoring ap-4000/4000m/4900m user guide interfaces 145 • out discards (ethernet/wireless-slot a/b): the number of error-free outbound packets chosen to be discarded to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. • out errors (...

  • Page 146

    Monitoring ap-4000/4000m/4900m user guide station statistics 146 station statistics this tab displays information on wireless clients attached to the ap and on wireless distribution system. Enable the monitoring station statistics feature (station statistics are disabled by default) by checking enab...

  • Page 147

    Monitoring ap-4000/4000m/4900m user guide station statistics 147 • time since last frame received: the time elapsed since the last frame from the associated wireless station (or wds link partner) was received. • number of stations and wds links: the number of stations and wds links monitored. The fo...

  • Page 148

    Monitoring ap-4000/4000m/4900m user guide mesh statistics 148 mesh statistics this tab displays statistics relating to the mesh portal: the network topology or the neighbor table. Selecting link statistics displays the mac address, ip address, recieve rate, transmit rate, receive errors, transmit er...

  • Page 149: Commands

    149 ap-4000/4000m/4900m user guide 6 commands this chapter contains information on the following command functions: • introduction to file transfer via tftp or http : describes the available file transfer methods. • update ap: download files via tftp or http to the ap. • retrieve file: upload config...

  • Page 150

    Commands ap-4000/4000m/4900m user guide introduction to file transfer via tftp or http 150 introduction to file transfer via tftp or http there are two methods of transferring files to or from the ap: tftp or http (or https if enabled): • downloading files (configuration, ap image, bootloader, licen...

  • Page 151

    Commands ap-4000/4000m/4900m user guide update ap 151 update ap update ap via tftp use the update ap via tftp tab to download configuration, ap image, license file, bootloader files, certificate and private key files, and cli batch file to the ap. A tftp server must be running and configured to poin...

  • Page 152

    Commands ap-4000/4000m/4900m user guide update ap 152 – ssh private key: the private key in ssh communications. See secure shell (ssh) settings for more information. – cli batch file: a cli batch file that contains cli commands to configure the ap. This file will be executed by the ap immediately af...

  • Page 153

    Commands ap-4000/4000m/4900m user guide update ap 153 a warning message gets displayed that advises the user that a reboot of the device will be required for changes to take effect. Figure 6-4 warning message 4. Click ok to continue with the operation or cancel to abort the operation. Note: an http ...

  • Page 154

    Commands ap-4000/4000m/4900m user guide retrieve file 154 retrieve file retrieve file via tftp use the retrieve file via tftp tab to upload files from the ap to the tftp server. The tftp server must be running and configured to point to the directory to which you want to copy the uploaded file. We s...

  • Page 155

    Commands ap-4000/4000m/4900m user guide retrieve file 155 retrieve file via http use the retrieve file via http tab to retrieve configuration files, cli batch files, or cli batch logs from the ap. For more information on cli batch files and cli batch logs see cli batch file . 1. Select the type of f...

  • Page 156

    Commands ap-4000/4000m/4900m user guide retrieve file 156 figure 6-10 file download dialog box 4. On clicking the save button the save aswindow displays. Select an appropriate filename and location and click ok..

  • Page 157

    Commands ap-4000/4000m/4900m user guide reboot 157 reboot use the reboot tab to save configuration changes (if any) and reset the ap. Enter a value between 0 and 65535 seconds; entering a value of 0 (zero) seconds causes an immediate reboot. Note that reset, described below, does not save configurat...

  • Page 158

    Commands ap-4000/4000m/4900m user guide reset 158 reset use the reset tab to restore the ap to factory default conditions. Since this will reset the ap’s current ip address, a new ip address must be assigned. See initialization for more information. Caution: resetting the ap to its factory default c...

  • Page 159

    Commands ap-4000/4000m/4900m user guide help link 159 help link use the help tab to configure the location of the ap help files. During initialization, the ap on-line help files are downloaded to the default location: c:/program files/orinoco/ap4x00x/html/index.Htm. To enable the help button on each...

  • Page 160: Troubleshooting

    160 ap-4000/4000m/4900m user guide 7 troubleshooting this chapter provides information on the following: • troubleshooting concepts • symptoms and solutions • recovery procedures • related applications note: this section helps you locate problems related to the ap device setup. For details about rad...

  • Page 161

    Troubleshooting ap-4000/4000m/4900m user guide symptoms and solutions 161 symptoms and solutions connectivity issues connectivity issues include any problem that prevents you from powering up or connecting to the ap. Ap unit will not boot - no led activity 1. Make sure your power source is operating...

  • Page 162

    Troubleshooting ap-4000/4000m/4900m user guide symptoms and solutions 162 2. The ap only contacts a dhcp server during boot-up. If your network’s dhcp server is not available while the ap is booting, the device will use the default ip address (169.254.128.132). Reboot the ap once your dhcp server is...

  • Page 163

    Troubleshooting ap-4000/4000m/4900m user guide symptoms and solutions 163 5. If you have a problem uploading a file, verify that the tftp server is configured to allow uploads (typically the default setting is to allow only downloads). Client connection problems client software finds no connection m...

  • Page 164

    Troubleshooting ap-4000/4000m/4900m user guide symptoms and solutions 164 caution: the forced reload procedure disconnects all users and resets all values to factory defaults. Power-over-ethernet (poe) the ap does not work 1. Verify that you are using a standard utp category 5 cable. 2. Try a differ...

  • Page 165

    Troubleshooting ap-4000/4000m/4900m user guide recovery procedures 165 recovery procedures the most common installation problems relate to ip addressing. For example, without the tftp server ip address, you will not be able to download a new ap image to the ap. Ip address management is fundamental. ...

  • Page 166

    Troubleshooting ap-4000/4000m/4900m user guide recovery procedures 166 – download a new image using the bootloader cli because the cli option requires a physical connection to the unit’s serial port, proxim recommends the scantool option. Download a new image using scantool to download the ap image,...

  • Page 167

    Troubleshooting ap-4000/4000m/4900m user guide recovery procedures 167 you must also connect the ap to a computer with a standard serial cable and use a terminal client, such as hyperterminal. From the terminal, enter cli commands to set the ip address and download an ap image. Preparing to download...

  • Page 168

    Troubleshooting ap-4000/4000m/4900m user guide recovery procedures 168 [device name]> show [device name]> reboot the ap will reboot and then download the image file. You should see downloading activity begin after a few seconds within the tftp server’s status screen. 8. When the download process is ...

  • Page 169

    Troubleshooting ap-4000/4000m/4900m user guide recovery procedures 169 figure 7-1 result of “show ip” cli command 6. Change the ip address and other network values using set and reboot cli commands, similar to the example below (use your own ip address and subnet mask). Note that ip address type is ...

  • Page 170

    Troubleshooting ap-4000/4000m/4900m user guide related applications 170 related applications radius authentication server if you enabled radius authentication on the ap, make sure that your network’s radius servers are operational. Otherwise, clients will not be able to log in. There are several rea...

  • Page 171: Command Line Interface (Cli)

    171 ap-4000/4000m/4900m user guide a command line interface (cli) this section discusses the following: • general notes • command line interface (cli) variations • cli command types • using tables and strings • configuring the ap using cli commands • set basic configuration parameters using cli comm...

  • Page 172

    Command line interface (cli) ap-4000/4000m/4900m user guide general notes 172 general notes prerequisite skills and knowledge to use this document effectively, you should have a working knowledge of local area networking (lan) concepts, network access infrastructures, and client-server relationships...

  • Page 173

    Command line interface (cli) ap-4000/4000m/4900m user guide general notes 173 cli error messages the following table describes the error messages associated with improper inputs or expected cli behavior. Tab complete the command line ? List available commands error message description syntax error i...

  • Page 174

    Command line interface (cli) ap-4000/4000m/4900m user guide command line interface (cli) variations 174 command line interface (cli) variations administrators use the cli to control access point operation and monitor network statistics. The ap supports two types of cli: the bootloader cli and the no...

  • Page 175

    Command line interface (cli) ap-4000/4000m/4900m user guide command line interface (cli) variations 175 figure a-2 results of “show” bootloader cli command.

  • Page 176

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 176 cli command types this guide divides cli commands into two categories: operational and parameter controls. Operational cli commands these commands affect access point behavior, such as downloading, rebooting, and so on...

  • Page 177

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 177 example 2. Display specific commands to show all commands that start with specified letters, enter one or more letters, then ? With no space between letters and ?. [device-name]>s? Figure a-4 result of “s?” cli command...

  • Page 178

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 178 figure a-7 result of “show iparp?” cli command example 4. Display prompts for successive parameters enter the command, a space, and then ?. Then, when the parameter prompt appears, enter the parameter value. The parame...

  • Page 179

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 179 help displays instructions on using control-key sequences for navigating a command line and displays command information and examples. 1. Using help as the only argument: [device-name]>help figure a-8 results of “help”...

  • Page 180

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 180 search lists the parameters supported by the specified table. This list corresponds to the table information displayed in the http interface. In this example, the cli returns the list of parameters that make up an entr...

  • Page 181

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 181 [device-name]>show network [device-name]>show mgmtipaccesstbl “set” cli command sets (modifies) the value of the specified parameter. To see a definition and syntax example, type only set and then press the enter key. ...

  • Page 182

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 182 example 2 - create a table entry or row use 0 (zero) as the index to a table when creating an entry. When creating a table row, only the mandatory table elements are required (comment is usually an optional table eleme...

  • Page 183

    Command line interface (cli) ap-4000/4000m/4900m user guide cli command types 183 figure a-10 results of “show network” and “show ip” cli commands example 6 - show individual and table parameters 1. View a single parameter. Syntax: [device-name]>show example: [device-name]> show ipaddr displays the ...

  • Page 184

    Command line interface (cli) ap-4000/4000m/4900m user guide using tables and strings 184 using tables and strings working with tables each table element (or parameter) must be specified, as in the example below. [device-name]>set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0 below are the ru...

  • Page 185

    Command line interface (cli) ap-4000/4000m/4900m user guide using tables and strings 185 the string delimiter does not have to be used for every string object. The single quote or double quote only has to be used for string objects that contain blank space characters. If the string object being used...

  • Page 186

    Command line interface (cli) ap-4000/4000m/4900m user guide configuring the ap using cli commands 186 configuring the ap using cli commands log into the ap using hyperterminal 1. Open your terminal emulation program (like hyperterminal) and set the following connection properties: • com port: • baud...

  • Page 187

    Command line interface (cli) ap-4000/4000m/4900m user guide set basic configuration parameters using cli commands 187 set basic configuration parameters using cli commands there are a few basic configuration parameters that you may want to setup right away when you receive the ap. For example: • set...

  • Page 188

    Command line interface (cli) ap-4000/4000m/4900m user guide set basic configuration parameters using cli commands 188 [device-name]>set snmprpasswd (snmp read password) [device-name]>set snmprwpasswd (snmp read/write) [device-name]>set snmpv3authpasswd (snmpv3 authentication password) [device-name]>...

  • Page 189

    Command line interface (cli) ap-4000/4000m/4900m user guide set basic configuration parameters using cli commands 189 argentina ar hungary hu peru pe armenia am iceland is philippines ph australia au india in poland pl austria at indonesia id portugal pt azerbaijan az ireland 5.8 ghz i1 puerto rico ...

  • Page 190

    Command line interface (cli) ap-4000/4000m/4900m user guide set basic configuration parameters using cli commands 190 enable and configure tx power control for the wireless interface(s) the tx power control feature lets the user configure the transmit power level of the card in the ap. Perform the f...

  • Page 191

    Command line interface (cli) ap-4000/4000m/4900m user guide set basic configuration parameters using cli commands 191 set up auto configuration the auto configuration feature which allows an ap to be automatically configured by downloading a specific configuration file from a tftp server during the ...

  • Page 192

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 192 other network settings there are other configuration settings that you may want to set for the ap. Some of them are listed below. • configure the ap as a dhcp server • configure the dns client • configure dhcp rel...

  • Page 193

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 193 configure dhcp relay perform the following command to enable or disable dhcp relay agent status. Note: you must have at least one entry in the dhcp relay server table before you can set the dhcp relay status to en...

  • Page 194

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 194 enable/disable closed system [device-name]>set wif closedsys shutdown/resume wireless service [device-name]>set wif wssstatus set load balancing maximum number of clients [device-name]>set wif lbmaxclients set the...

  • Page 195

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 195 set the distance between aps [device-name]>set wif distaps (see below) [device-name]>reboot 0 set ethernet speed and transmission mode [device-name]>set etherspeed (see below) [device-name]>reboot 0 set interface ...

  • Page 196

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 196 set communication ports [device-name]>set httpport (default is 80)> [device-name]>set telport (default is 23)> configure secure socket layer (https) enabling ssl and configuring a passphrase allows encrypted secur...

  • Page 197

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 197 configure wireless distribution system create/enable wds [device-name]>set wdstbl partnermacaddr status enable enable/disable wds [device-name]>set wdstbl status note: is 3.1–3.6 (wireless a) or 4.1–4.6 (wireless ...

  • Page 198

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 198 [device-name]>set radiustbl 1.2 profname "mac authentication" seraddrfmt 1 sernameorip 20.0.0.30 port 1812 ssecret public responsetm 3 maxretx 3 acctupdtintrvl 0 macaddrfmt 1 authlifetm 900 radaccinactivetmr 5 vla...

  • Page 199

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 199 set rogue scan parameters perform the following command to enable or disable rogue scan on a wireless interface and configure the scanning parameters. The cycletime parameter is only configured for background scan...

  • Page 200

    Command line interface (cli) ap-4000/4000m/4900m user guide other network settings 200 set security profile parameters configure a security profile with non secure security mode [device-name]>set secprofiletbl secmode nonsecure status enable example: [device-name]>set secprofiletbl 2 secmode nonsecu...

  • Page 201

    Command line interface (cli) ap-4000/4000m/4900m user guide cli monitoring parameters 201 cli monitoring parameters using the show command with the following table parameters will display operating statistics for the ap (these are the same statistics that are described in the monitoring section). • ...

  • Page 202

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 202 parameter tables objects contain groups that contain both parameters and parameter tables. Use the following tables to configure the access point. Columns used on the tables include: • name - parameter, group, or table ...

  • Page 203

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 203 – broadcast filtering table - control the type of broadcast packets forwarded to the wireless network – tcp/udp port filtering - filter ip packets based on tcp/udp port • alarms parameters – snmp table host table parame...

  • Page 204

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 204 system parameters * available only on aps with model numbers ending with -wd. When available, this object must be configured before any interface parameters can be set. Country identifiers note: all countries may not be...

  • Page 205

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 205 finland indoor fi1 outdoor fi2 france indoor fr1 outdoor fr2 germany indoor de1 outdoor de2 greece indoor gr1 outdoor gr2 hungary indoor hu1 outdoor hu2 ireland indoor ie1 outdoor ie2 italy indoor it1 outdoor it2 latvia...

  • Page 206

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 206 inventory management information the inventory management commands display advanced information about the ap’s installed components. You may be asked to report this information to a representative if you contact custome...

  • Page 207

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 207 dns client for radius name resolution dhcp server parameters * the dhcp server (dhcpstatus) can only be enabled after a dhcp ip pool table entry has been created. Dhcp server table for ip pools * ip addresses must be fr...

  • Page 208

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 208 dhcp relay group the dhcp relay group allows you to enable or disable dhcp relay agent status. Dhcp relay server table the dhcp relay server table contains the commands to set the table entries. The ap supports the conf...

  • Page 209

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 209 sntp parameters link integrity parameters * link integrity cannot be configured when the ap is configured to function as a mesh ap. Link integrity ip target table name type value access cli parameter sntp group group n/...

  • Page 210

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 210 interface parameters wireless interface parameters the wireless interface group parameter is wif. Wireless interface a (802.11a/4.9 ghz radio) uses table index 3 and wireless interface b (802.11b/g radio) uses table ind...

  • Page 211

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 211 common parameters to 802.11a, 4.9 ghz, and 802.11b/g * for 802.11a aps certified in the etsi and telec regulatory domains and operating in the middle frequency band, disabling auto channel select will limit the availabl...

  • Page 212

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 212 ** each 802.11 packet is acknowledged by the receiving station. On links longer than about 100m, the time that it takes for the ack to get back to the sending station is long enough to cause the sending station to belie...

  • Page 213

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 213 4.9 ghz specific parameters 802.11a specific parameters name type value access cli parameter operating frequency channel integer varies by regulatory domain and country. See available channels rw channel supported data ...

  • Page 214

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 214 * available for the 5 ghz frequency band in the fcc regulatory domain only. † super mode must be enabled on the wireless interface before turbo mode can be enabled. Turbo mode and mesh mode (either mesh ap or mesh porta...

  • Page 215

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 215 802.11b specific parameters 802.11b/g specific parameters name type value access cli parameter operating frequency channel integer 1 - 14; available channels vary by regulatory domain/country; see available channels rw ...

  • Page 216

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 216 * also for 802.11g-wifi mode. 802.11g-wifi has been defined for wi-fi testing purposes; it is not recommended for use in your wireless network environment. † available in 802.11b/g or 802.11g modes only. Transmit rate i...

  • Page 217

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 217 wireless distribution system (wds) parameters wireless distribution system (wds) security table parameters the wds security table manages wds related security objects. Wireless interface ssid/vlan/profile parameters the...

  • Page 218

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 218 ethernet interface parameters mesh parameters . Radius accounting status per vlan integer enable disable rw acctstatus mac acl status per vlan integer enable disable rw aclstatus security profile integer32 user defined ...

  • Page 219

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 219 * higher roaming threshold value creates a more static mesh environment. Lower roaming threshold value creates a more dynamic mesh environment. † a qos profile corresponding to this index number must exist. ‡ this comma...

  • Page 220

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 220 management parameters secure management parameters snmp parameters http parameters * the help link must be set to an http address. Use the forward slash character ("/") rather than the backslash character ("\") when con...

  • Page 221

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 221 telnet parameters serial port parameters radius based management access parameters the radius based management access parameters allow you to enable http or telnet radius management access, enable or disable local user ...

  • Page 222

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 222 ssh parameters the following commands enable or disable ssh and set the ssh host key. The ap ssh feature, open-ssh, confirms to the ssh protocol, and supports ssh version 2. The following ssh clients have been verified ...

  • Page 223

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 223 ip access table parameters when creating table entries, you may either specify the argument name followed by argument value or simply enter the argument value. When only the argument value is specified, then enter the v...

  • Page 224

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 224 note: the filter operation type (passthru or block) applies only to the protocol filters that are enabled in this table. Static mac address filter table protocol number octet string n/a rw protonumber protocol name (opt...

  • Page 225

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 225 proxy arp parameters ip arp filtering parameters broadcast filtering table tcp/udp port filtering the following parameters are used to enable/disable the port filter feature. Tcp/udp port filtering table the following p...

  • Page 226

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 226 alarms parameters snmp table host table parameters when creating table entries, you may either specifying the argument name followed by argument value. Cli applies default values to the omitted arguments. Due to the nat...

  • Page 227

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 227 syslog parameters the following parameters configure the syslog settings. Note: when heartbeat is enabled, the ap periodically sends a message to the syslog server to indicate that it is active. The frequency with which...

  • Page 228

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 228 bridge parameters spanning tree parameters spanning tree priority and path cost table storm threshold parameters name type value access cli parameter spanning tree group n/a r stp spanning tree status integer enable dis...

  • Page 229

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 229 storm threshold table intra bss subscriber blocking the following parameters control the intra bss traffic feature, which prevent wireless clients that are associated with the same ap from communicating with each other:...

  • Page 230

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 230 radius parameters general radius parameters radius server configuration parameters note: use a server name only if you have enabled the dns client functionality. See dns client for radius name resolution . Name type val...

  • Page 231

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 231 security parameters mac access control parameters mac access control table rogue scan configuration table the rogue scan configuration table allows you to enable or disable rogue scan and configure the scanning paramete...

  • Page 232

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 232 security profile table the security profile table allows you to configure security profiles. A maximum of 16 security profiles are supported per wireless interface. Each security profile can contain one or more enabled ...

  • Page 233

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 233 encryption key format if wep security mode is configured, then the appropriate key size must be configured. The ap supports 63-, 128-, and 152-bit encryption keys. Encryption keys may be configured using either hexadeci...

  • Page 234

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 234 wireless multimedia enhancements (wme)/quality of service (qos) parameters the wireless multimedia enhancements commands enable and configure wireless multimedia enhancement/quality of service parameters per wireless in...

  • Page 235

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 235 specifying the mapping between ip precedence/dscp ranges and 802.1d priorities the qos ip dscp to 802.1d mapping table specifies the mapping between ip precedence/dscp ranges and 802.1d priorities. Qos enhanced distribu...

  • Page 236

    Command line interface (cli) ap-4000/4000m/4900m user guide parameter tables 236 examples: show qosedcatbl (or qosqapedcatbl) set qosedcatbl (or qosqapedcatbl) . For example: set qosedcatbl 3.1 cwmin 15 defining the qos policy used for a wireless interface ssid the qos policy object configures the q...

  • Page 237

    Command line interface (cli) ap-4000/4000m/4900m user guide cli batch file 237 cli batch file a cli batch file is a user-editable file that lists a series of cli set commands, that can be uploaded to the access point to change its configuration. The access point executes the cli commands specified i...

  • Page 238

    Command line interface (cli) ap-4000/4000m/4900m user guide cli batch file 238 reboot behavior when a cli batch file contains a reboot command, the reboot will occur only after the entire cli batch file has been executed. There are two methods of uploading the cli batch file: • upload • upload and r...

  • Page 239: Ascii Character Chart

    239 ap-4000/4000m/4900m user guide b ascii character chart you can configure wep encryption keys in either hexadecimal or ascii format. Hexadecimal digits are 0-9 and a-f (not case sensitive). Ascii characters are 0-9, a-f, a-f (case sensitive), and punctuation marks. Each ascii character correspond...

  • Page 240: Specifications

    240 ap-4000/4000m/4900m user guide c specifications • software features • hardware specifications • available channels software features the tables below list the software features available on the ap-4000/4000m/4900m. • number of stations per bss • management functions • advanced bridging functions...

  • Page 241

    Specifications ap-4000/4000m/4900m user guide software features 241 advanced bridging functions medium access control (mac) functions * dfs is required for 802.11a aps certified in the etsi and telec regulatory domains and operating in the middle frequency band. When acs is disabled, available chann...

  • Page 242

    Specifications ap-4000/4000m/4900m user guide software features 242 security functions * key lengths supported by 802.11a/4.9 ghz: 64-bit, 128-bit, and 152-bit. Key lengths supported by 802.11b: 64-bit and 128-bit. Key lengths supported by 802.11b/g: 64-bit, 128-bit, and 152-bit. † eap-md5, eap-tls,...

  • Page 243

    Specifications ap-4000/4000m/4900m user guide software features 243 network functions * includes fallback to primary radius server, radius session timeout, radius multiple mac address formats, radius dns host name support, radius start/stop accounting. † dhcp client requests and ip lease renewals ar...

  • Page 244

    Specifications ap-4000/4000m/4900m user guide hardware specifications 244 hardware specifications category specification physical dimensions (h x w x l) 1 x 4.75 x 7.1 in (25 x 121 x 180 mm) plus additional antenna adaptor for ap-4900m weight ap:4000/4000m unit: .65 lb (.295 kg) ap-4900m unit: .75 l...

  • Page 245

    Specifications ap-4000/4000m/4900m user guide available channels 245 available channels available channels vary based on radio, country, and frequency band. To verify which channels are available for your product: 1. Locate the product model number on the underside of your ap unit or on the unit’s b...

  • Page 246

    Specifications ap-4000/4000m/4900m user guide available channels 246 4.9 ghz channels (ap-4900m only) wd sku channels by country available channel bands depend on the selected country and mode of use (indoor/outdoor). The typical channels available in each 802.11a frequency band are as follows: chan...

  • Page 247

    Specifications ap-4000/4000m/4900m user guide available channels 247 hungary indoor l, m, h 1 - 13 hu1 hu outdoor h 1 - 13 hu2 hu ireland indoor l, m, h 1 - 13 ie1 ie outdoor h 1 - 13 ie2 ie italy indoor l, m, h 1 - 13 it1 it outdoor h 1 - 13 it2 it latvia indoor l, m, h 1 - 13 lv1 lv outdoor h 1 - ...

  • Page 248

    248 ap-4000/4000m/4900m user guide d technical services and support see the following sections: • obtaining technical services and support • support options – proxim eservice web site support – telephone support – servpak support obtaining technical services and support if you are having trouble uti...

  • Page 249

    Technical services and support ap-4000/4000m/4900m user guide support options 249 support options proxim eservice web site support the proxim eservice web site is available 7x24x365 at http://support.Proxim.Com . On the proxim eservice web site, you can access the following services: • new product r...

  • Page 250: Statement of Warranty

    250 ap-4000/4000m/4900m user guide e statement of warranty warranty coverage proxim wireless corporation warrants that its products are manufactured solely from new parts, conform substantially to specifications, and will be free of defects in material and workmanship for a warranty period of 1 year...

  • Page 251

    Statement of warranty ap-4000/4000m/4900m user guide other information 251 and shipping instructions. Buyer must return the defective product to proxim wireless, properly packaged to prevent damage, shipping prepaid, with the rma number prominently displayed on the outside of the container. Calls to...