- DL manuals
- PS Engineering
- Intercom System
- PMA8000BT
- System Installation And Operation Manual
PS Engineering PMA8000BT System Installation And Operation Manual
9800 Martel Road
Lenoir City, TN 37772
www.ps-engineering.com
P
P
M
M
A
A
8
8
0
0
0
0
0
0
B
B
T
T
Document P/N 200-890-0702
Revision 1, Oct. 2010
Audio Selector Panel with Marker Beacon Receiver
High-fidelity Stereo Intercom
System Installation and Operation Manual
FAA- TSO C50c, C35d
EASA ETSO C50c, 2C35d
Patented under one or more of the following;
No. 4,941,187; 5,903,227; 6,160,496 and 6,493,450
PS Engineering, Inc. 2010 ©
Copyright Notice
Any reproduction or retransmittal of this publication, or any portion thereof, without the expressed written permission of PS Engi-
neering, Inc. is strictly prohibited. For further information contact the Publications Manager at PS Engineering, Inc., 9800 Martel
Road, Lenoir City, TN 37772. Phone (865) 988-9800, email contact@ps-engineering.com.
In certified aircraft, warranty is not valid unless this product is installed by an
Authorized PS Engineering dealer.
Summary of PMA8000BT
Page 1
9800 martel road lenoir city, tn 37772 www.Ps-engineering.Com p p m m a a 8 8 0 0 0 0 0 0 b b t t document p/n 200-890-0702 revision 1, oct. 2010 audio selector panel with marker beacon receiver high-fidelity stereo intercom system installation and operation manual faa- tso c50c, c35d easa etso c50c...
Page 2
Table of contents section i – general information......................................................................... 1-1 1.1 introduction ..................................................................................................................................... 1-1 1.2 scope............
Page 3
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page ii rev. 1, oct. 2010 2.12.5 i nternal r ecorder c heckout .......................................................................................... 2-14 2.12.6 f unction b utton c ...
Page 4
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 1-1 rev. 1, oct. 2010 section i – general information 1.1 introduction the pma8000bt represents another evolutionary step in cockpit audio control and intercommunications utility. U...
Page 5
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 1-2 rev. 1, oct. 2010 the small volume knob controls the intercom level for the pilot and copilot, while the large knob controls the passenger intercom volume. Intercom squelch is a...
Page 6
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 1-3 rev. 1, oct. 2010 audio selector specifications audio selector panel input impedance: 510 input isolation: -60 db (min.) speaker muting: -60 db (min.) speaker output (into 4 ...
Page 7
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 1-4 rev. 1, oct. 2010 1.6 equipment supplied 1 ea. Of the following units: model description part number pma8000bt pma8000bt audio panel with marker, stereo intercom, and blue- toot...
Page 8
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-1 rev. 1, oct. 2010 section ii - installation 2.1 general information 2.1.1 scope this section provides detailed installation and interconnection instructions for the ps engineeri...
Page 9
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-2 rev. 1, oct. 2010 the unit aside in a safe location until needed. Install the tray using six clip nuts (475 -630-0002), and six fhp 6-32 x ½" screws (475-632-0012). The audio se...
Page 10
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-3 rev. 1, oct. 2010 radiated signals can be a factor when low level microphone signals are "bundled" with current carrying power wires. Keep these cables physically separated. It ...
Page 11
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-4 rev. 1, oct. 2010 2.4.5 audio panel interface the pma8000bt is designed to interface with standard aircraft avionics, and presents a 510 receiver impedance. For best results, ...
Page 12
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-5 rev. 1, oct. 2010 unswitched #1 is presented to the pilot headphone in fail-safe (off) mode. Note inputs 1, 2 and 4 are fixed (1:1), and any audio level adjustments must be made...
Page 13
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-6 rev. 1, oct. 2010 buttons for more than one second. For units with serial number w04747 and below, an internal modifica- tion can be made that will allow the pma8000bt to provid...
Page 14
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-7 rev. 1, oct. 2010 2. Install the blue jumper located in the back corner near the sub-d connectors on both pins of j4. See figure #2-3. Figure 2-3 jumper location 4. Place the li...
Page 15
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-8 rev. 1, oct. 2010 2.5.1 entertainment inputs the pma8000bt has two independent music inputs, plus a front mounted jack that is connected to entertainment 1. Entertainment input ...
Page 16
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-9 rev. 1, oct. 2010 if the single-source mode is activated through the function keys, the front panel jack (and music 1) is con- nected to all intercom positions, regardless of th...
Page 17
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-10 rev. 1, oct. 2010 figure 2-4- pma8000bt adjustments, top cover speaker volume- turn adjustment clockwise to increase cabin speaker output. Marker beacon volume, turn adjustment...
Page 18
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-11 rev. 1, oct. 2010 2.8 communications antenna installation notes for best results while in split mode, it is recommended that the one vhf communications antenna is l o- cated on...
Page 19
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-12 rev. 1, oct. 2010 2.9 pma8000bt pin assignments j1 function j2 function 1 mkr ant 1 pilot phones low 2 mkr ant low 2 copilot phones low 3 telephone audio in 3 copilot phones (l...
Page 20
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-13 rev. 1, oct. 2010 2.10 wiring checkout after wiring is complete, verify power is only on pins 8 and 9 of the j2 and airframe ground on connec- tor pins 10 and 11. Failure to do...
Page 21
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 2-14 rev. 1, oct. 2010 14. Verify that the appropriate led in the lower button row blinks when either push to talk is keyed. 15. Verify proper intercom system operation in the a ll ...
Page 22
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-1 rev. 1, oct. 2010 section iii operation 3.1 scope this section provides detailed operating instructions for the ps engineering pma8000bt, audio selector panel/marker beacon rece...
Page 23
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-2 rev. 1, oct. 2010 when switching from c om 1 to c om 2 while com 2 was not previously selected, c om 1 audio will be switched off. In essence, switching the mic selector will no...
Page 24
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-3 rev. 1, oct. 2010 mic will be transferred to the selected com radio. The telephone party will not hear atc communic a- tions, and vice versa. In crew mode, only the pilot and co...
Page 25
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-4 rev. 1, oct. 2010 accurate location of the outer marker. Holding the mkr button for one second activates marker test lamp, labeled "t/m" and illuminates all three lamps simultan...
Page 26
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-5 rev. 1, oct. 2010 adjust the radios and intercom volume for a comfortable listening level. Most general aviation headsets today have built-in volume controls; therefore, volume ...
Page 27
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-6 rev. 1, oct. 2010 nunciations of the mode selected. Mode 1 - music will mute with either intercom or radio - mute button is lit. Voice annunciation is "mute on." mode 2 - “karao...
Page 28
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-7 rev. 1, oct. 2010 crew in iso intercom mode, when the pma8000bt is in the tel mode, the pilot position is in the "phone booth." only the pilot will hear the telephone, and only ...
Page 29
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-8 rev. 1, oct. 2010 3.11 smart function keys (sfk) with virtual tech support, the configuration process is self-directed. Sfk annunciations are heard by the pilot and copilot posi...
Page 30
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-9 rev. 1, oct. 2010 when function a is toggled into “alternate intercom function,” the passengers will not hear aircraft radios, even in the all mode. They will be able to convers...
Page 31
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-10 rev. 1, oct. 2010 music 2 is provided to the passenger positions regardless of intercom mode, when the audio panel is in standard music distribution, and also in alternate musi...
Page 32
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-11 rev. 1, oct. 2010 you can answer a call by pushing the tel button while it is ringing. Calls can be answered from the tel e- phone handset or the audio panel. You can disconnec...
Page 33
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-12 rev. 1, oct. 2010 3.12.4 bluetooth music control the pma8000bt can control some bluetooth music devices. When the music is playing, press and hold the “function” button (tel), ...
Page 34
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 3-13 rev. 1, oct. 2010 figure 3-3 playback controls.
Page 35
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 page 4-1 rev. 1, oct. 2010 section iv – warranty and service 4.1 warranty in order for the factory warranty to be valid, the installations in a certified aircraft must be accomplished by...
Page 36
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 appendix a rev. 1, oct. 2010 appendix a – external ptt hook up part of the installation includes the installation of ptt (push to talk) switches that allow the use of your aircraft radio...
Page 37
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 rev. 1, oct. 2010 appendix b – pma8000 installation drawings j2 j1 viewed from back 15 30 44 1 16 31 15 30 44 1 16 31 solder lug (mount as convenient) rear plate detail (not to scale) 0....
Page 38
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 rev. 1, oct. 2010 appendix c – j1 connector interconnect co m 1 a ud io hi co m 1 m ic k e y co m 1 l o communications transceiver #1 communications transceiver #2 nav 1 a ud io hi nav 1...
Page 39
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 appendix d rev. 1, oct. 2010 appendix d – j2 connector interconnect 22 20 31 16 1 35 36 24 23 25 4 3 2 copilot phones (r) copilot phones (l) copilot phones lo pass. 1 mic jack pass. Mic ...
Page 40
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 appendix e rev. 1, oct. 2010 appendix e – instructions for faa form 337 and continuing airworthiness 9.1 instructions for faa form 337, audio panels one method of airworthiness approval ...
Page 41
Ps engineering pma8000bt audio selector panel and intercom system installation and operator’s manual 200-890-0702 appendix f rev. 1, oct. 2010 appendix f – rtca do160d environmental qualification form audio selector panel/intercom/marker beacon receiver part number: 050-890-( ) faa tso number: c50c,...