Summary of Q-T3
Page 1
1.
Page 2
2 voltage see nameplate power output 1400w turbine 3 stage airflow 2800 l/min max working pressure 0.41 bar (6 psi) turbine dimensions (lxwxh) 325mm x 250mm x 325mm net weight 8.5 kgs ( 18.7 lbs) material applications: * automotive refinish * architectural * marine * industrial * aerospace * wood * ...
Page 3
3 general safety rules warning! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and / or serious personal injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool. Save...
Page 4
4 a power tool. Do not use tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. B) use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid sa...
Page 5
5 5) service have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. If the supply cord of this power tool is damaged it must be replaced by a specially prepared cord available through the se...
Page 6
6 • always ensure fire extinguishing equipment is readily available and properly maintained. Always inspect spraying area • keep the spraying area free from obstructions. • make sure the spraying area has good ventilation to safely remove vapors and mists. • never keep flammable material in spraying...
Page 7
7 next heavier gauge. 2. Hose: use only grounded hoses. 3. Spray gun: grounding is obtained through connection to a properly grounded hose and turbine. W h e n s p r a y i n g & c l e a n i n g w i t h flammable paints and thinners 1. When spraying with flammable liquids, the unit must be located a ...
Page 8
8 2. Test the spray pattern and atomization on a test piece. Hold about 20cm (8 inches) away. Turn the pattern adjustor knob for the desired pattern. 3. Adjust the speed control knob on the turbine to control the air volume. Generally, it is best to use the minimum a i r v o l u m e w h i c h w i l ...
Page 9
9 choosing fluid sets: the fluid set includes a needle, a nozzle and an air cap. These parts are a matched set. Do not mix parts from other sizes. The standard fluid set which comes with the gun is a 1.3mm, which will work well for most applications. Different sizes of fluid set will give different ...
Page 10
10 clean-up: always clean the gun at the end of the day or between colors 1. U s i n g a r a g m o i s t e n e d w i t h a compatible solvent, clean the cup and the outside of the gun. 2. Remove the air cap, baffle and nozzle and clean with a cleaning brush. Take care to avoid damage to the air cap ...
Page 11: Wiring
11 wiring.
Page 12: Hvlp Turbine Exploded View
12 hvlp turbine exploded view 20 54 53 52 51 50 30 31 27 26 25 27 26 25 29 29 28 24 31 30 33 32 34 43 44 48 20 36 23 21 20 42 18 13 15 14 13 15 14 13 12 11 09 10 09 08 07 03 04 05 06 16 17 38 37 39 02 01 55 56 57 58 59 60 59 61 62 63 22 35 49 19 40 41 45 47 46 60- 2 60- 1 64 65.
Page 13: Hvlp Turbine Parts List
13 hvlp turbine parts list no. Parts name q'ty 1. Hex nut-left hand thread m6 1 2. Fan 70 x 6 1 3. Motor housing 1 4. Brush holder 2 5. Carbon brush 7 x 12 2 6. Screw m4 x 12 4 7. Stator 1 8. Stator screw m5 x 60 2 9. Bearing 6200 2ru 2 10. Armature 1 11. Motor front cover 1 12. Spacer-large 1 13. T...
Page 14: Hvlp Gun
14 hvlp gun exploded view.
Page 15: Hvlp Gun Parts List
15 hvlp gun parts list no. Parts name q'ty g1-1 air cap retaining ring 1 g1-2 air cap 1 g2 nozzle 1 g3 baffle 1 g4 gun body 1 g5 socket cap screw 1 g6 pattern adjustor 1 g7 o-ring 1 g8 seat 1 g9 adjustor support 1 g10 adjustor knob 1 g11 bushing 1 g12 needle spindle 1 g13 spring 1 g14 seal 1 g15 o-r...