Q90 Q2PCVI Instructions For Installation, Use And Maintenance Manual - page 4
IS535 ECN 3673
Page 4 of 9
POTENTIAL TROUBLESHOOTING AND SOLUTIONS
Even during correct use of the appliance, malfunctions and
breakdowns may occur. Common situations are listed
below, and checks an installer should make before
contacting the technical support centre are indicated.
If after checking, the problem remains, switch the appliance
off immediately and disconnect it from the power supply.
Contact the technical support centre.
Insufficient heating of cooking zone
Unsuitable pan material
– use suitable pan
material.
Continuous heating of cooking zone at maximum power
Knob switch faulty
– check and replace knob
switch.
Empty cooking zone starts operating
Pan detection sensor faulty
– replace generator.
Small metal objects are heated
Pan detection sensor faulty
– replace generator.
No heating of cooking zone
Pan base less than 12cm
– use larger pan.
Generator defective
– replace generator.
No reaction of appliance
Mains fuse/mains supply interrupted
– check
mains connection.
Fuses blow when switching on
Short circuit in generator
– replace generator.
REPLACING COMPONENTS WITH SPARES
ATTENTION: This section exclusively concerns technical
assistance personnel.
IMPORTANT: Before any service or maintenance, switch
off at the mains switch and disconnect the appliance from
the power supply.
All servicing, maintenance and component replacement
must be carried out by a qualified person.
Do not touch sealed components.
Inductors / Generator
Remove control knobs and control panel.
Disconnect the inductor. Remove the
conveyor/filter. Remove the conductor. Replace.
Potentiometer
Remove control knobs and control panel.
Disconnect the potentiometer from the generator.
Replace potentiometer and LED.
Glass ceramic induction cooking hob
In the event that the glass ceramic surface breaks,
replace it with an original part from our company.
INSTRUCTIONS FOR USE AND MAINTENANCE
ATTENTION: This appliance is intended for professional
use and therefore must be used by qualified or trained
personnel. It is essential to monitor the appliance during
use. During operation, parts may become hot
– avoid
accidental contact.
Ensure plug/socket is accessible at all times.
If the appliance is fitted with castors, use caution
at all times when moving and lock castors when
appliance is in position.
Installation and conversion to different voltages must be
carried out by qualified and authorised installers. In the
event of problems or malfunction, switch off the appliance
at the mains. In the event of a damaged supply cord, it
must be replaced by the manufacturer, its service agent or
similarly qualified person.
If the ceramic surface is cracked, switch off at the mains
supply and contact service support.
For repairs, refer only to the authorised assistance centres
and use only genuine replacement parts
Before using the appliance, read this manual and keep it for
future reference.
The induction generator has an internal system for cooling
down. Please make sure air input and output vents are not
obstructed.
Metallic objects should not be placed on the hob surface as
they will quickly become hot.
Operators with a pacemaker or metal prosthesis should
consult their doctor before using this appliance.
Operation
Note
Only use induction suitable pots and pans with a flat bottom
and with a minimum diameter of at least 12cm for the
cooking area. The pan bottom should be clean, smooth
and dry to avoid the ceramic cooking hob being scratched.
Do not place aluminium foil or plastic containers on the
ceramic cooking hob whilst it is hot, and do not use the hob
as a storage surface. The pan should be placed centrally
over the target ring of the ceramic glass.
Glass ceramic induction cooking hob
The glass ceramic cooking hob is provided with control
knobs and indicator display integrated into the printed
surface:
Potentiometer knob to set cooking temperature.
Green neon to indicate power to the appliance.
The potentiometer knob displays the following:
Back hob
Front hob
Off
Power level
Maximum
Switching on the glass ceramic cooking hob
Turn the knob to the position indicating the desired
cooking temperature
– the green neon illuminates.
Select the temperature by turning the
potentiometer knob
– the lowest level corresponds
ENG