QFX BT-207 Instruction Manual - page 4
EN-6
EN-5
EN-
Remote Control
USE CLOCK
to setup the time of the unit
1. connect the ac on(
.
2. short according to the time button, the time will flashing on the lcd display.
3. Rotate BACK、NEXT to select the number of the time. you can setup the time format by
12h or 24h.
4. press time button to confirm.
5. then you can set the hour and the minute with the same method of steps 3- 4.
6.
with the same method of steps 3- 4.
Rotate
The following operation must be in standby mode)
after setup the unit time, long press the time button can setup the unit begin working time ,
Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/aux/blue mode,
the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise
it playusb or aux mode first.
Radio reception
1.
FUNCTION
select RADIO
.
.Press BAND to select the desired wave band: FM STEREO, AM, FM, FM ST.
3.Tune to required station by
Manual Tuning: Rotate BACK or NEXT and then release within 1 sec.
Auto Tuning:
Preset Channel:(FM 30 Preset memories,
)
(1)
BACK/
Select desired station.
(2) Press PROGRAM button once , The MEMORY number indicator begins steady
in the display.
(3) Press PRESET-UP OR PRESET- DN buttons to select the desired number.
(4) Press PROGRAM button to save that station.
(5) Repeat steps (1) to (4) procedures for other stations.
4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you
selected or Press number key on the remote control.
5.
6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.
7.Turn off the radio by press FUNCTION button select other mode or press power button
to off the unit.
Press
button
mode
Press the play/pause button enter the automatic channel
mode, and to be put automatically sets.
[VOL-]or [VOL +] to adjust the volume.
2
Rotate BACK/ NEXT or press PRE- DN / PRE- UP.
scan
AM 10 preset memories
Rotate
NEXT
Rotate
8.Switch on again after shut down, the memory frequency still exists.
MONO/STEREO
-Press MO/ST button once, to mono state.
-Press MO/ST button twice, to stereo state, stereo is displayed.
* Please pull out the plastic paper from the battery door before use the remote control.
* When the remote control operation becomes unstable or the distance from which the
remote control works is shorter. replace the batteries with new ones.
* Using the remote control unit
To use the remote unit, point at the REMOTE SENSOR and press the buttons gently and
firmly. Remote control operation is possible within approximate 18ft (6m). However, since
the remote control range is less when the unit is used at an angle, use directly in front of
the REMOTE SENSOR, for maximum distance.
Do not expose the REMOTE SENSOR to strong light (direct sunlight or artificial lighting)
and make sure that there are no obstacles between the REMOTE SENSOR and the
remote control unit.
1. POWER BUTTON
2. OPEN/CLOSE BUTTON
3. INTRO BUTTON
4. MUTE BUTTON
5. RANDOM BUTTON
6. P- UP BUTTON
7. REPEAT/MO/ST BUTTON
8. PROGRAM BUTTON
9. BACK BUTTON
10. FUNCTION BUTTON
11. NEXT BUTTON
12. EQ BUTTON
13. PLAY/ PAUSE BUTTON
14. P- DOWN BUTTON
15. BBS BUTTON
16. STOP/BAND BUTTON
17. NUMBER KEY
18. VOL- BUTTON
19. VOL+ BUTTON
4
5
1
9
10
14
15
18
19
6
2
11
8
7
13
12
17
16
3
RANDOM BUTTON
-In the player CD/MP3/USB/AUX , press the RANDOM button can be played at random.
Press again to cancel.
BBS BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the BASS button can make into the
bass state. Press again to cancel.
EQ BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the EQ button to change music style.
-When playing the music, press this button is in the classica-rock-popular-jazz-FLR.
MUTE BUTTON
-In the player CD/MP3/USB/BT/AUX/ RADIO, press the MUTE button to enter the mute state.
Press again to restore volume.
INTRO BUTTON
-In the player CD/MP3/USB,press the INTRO button into 10 seconds browsing repertoire
state, press again cancel browse.