1. DL manuals
  2. Qlink
  3. Scooter
  4. Achille 150
  5. User Manual

Qlink Achille 150 User Manual

Summary of Achille 150

  • Page 1

    Thank you for your selection of this qlink scooter. It represents high technology and reliability, the emission of this vehicle has reached the latest national emission standard, therefore it is a really environment-friendly motorcycle that may satisfy the demands of modern society. It has been manu...

  • Page 2

    The following information appears as signs in this user's manual this sign indicates procedures must be followed to avoid injury of yourself, other people or the motorcycle. This sign indicates procedures must be followed to avoid damage to the motorcycle and yourself. This sign indicates procedures...

  • Page 3

    Main points for safe riding names of parts of the motorcycle motorcycle identification functions of the controllers main switch indicator speedometer oil capacity indication meter handlebar switch rear brake lever front brake lever steering lock fuel tank cap starting lever trunk rearview mirror kic...

  • Page 4

    Use of engine oil maintenance records schematic circuit diagram 31 32 33 specifications contents replacement of gear oil air filter maintenance for the air filter adjustment of carburetor adjustment of idling speed adjustment of the throttle handle adjustment of valve clearance inspection of spark p...

  • Page 5

    Please give clear signals in case of the situations listed below : turning left turning right it's very dangerous to brake on a damp road. Please avoid any emergency brake to prevent slip of the motorcycle. When parking on a damp road, put on the brake slowly. Slow down your motorcycle when approach...

  • Page 6

    Names of parts of the motorcycle 1.Taillight / rear stop lamp 2.Muffler 3.Main stand 4.Battery ( fuse included) 5.Main switch ( seat lock included) 6.Headlamp 7.Side stand 8.Front wheel 9.Front fender 10.Rearview mirror 11.Trunk 12.Seat 13.Fuel tank cap 14.Starting lever 15.Rear wheel 16.Gasoline pu...

  • Page 7

    Motorcycle identification vin number vin number is stenciled on the main beam tube at its right lower position and in the middle part of the frame. Engine number engine number is stamped on the left lower part of the left crankcase. Please learn by heart your engine number so when you are purchasing...

  • Page 8

    1. Turn signal indicator when the turn signal lamp switch functions, this indicator flashes. 2. High beam indicator when the motorcycle uses high beam lamp, this indicator is on. Speedometer can display the riding speed of the motorcycle (in km/h or mile/h).It is equipped with a milemeter that may a...

  • Page 9

    Lighting switch when the lighting switch is on"●"position,all the illu- -minating lamps will be off. Shift the lighting switch to" " position,you can light up the headlamp, taillight, position lamp, and instrument light. Front brake lever the front brake lever is located at the right grip and when g...

  • Page 10

    Starting lever screw out the starting lever towards the outer side of the engine. Tread the starting lever slightly with foot till the gear gets engaged and then start the engine by fast and forceful treading of the starting lever. When using starting lever, use throttle grip to refuel slightly and ...

  • Page 11

    The trunk, when exposed under the sunshine, will easily get hot do not place any flammable articles inside the trunk. Do not put any valuables or breakables things inside the trunk. The trunk will easily get wet in rainy days or during motorcycle cleaning. Articles liable to get damp should be well ...

  • Page 12

    Wheels and tires tire pressure, wear and deflection status various wire cables check of the motion state. And lubricate when necessary brake handlebar pivot check of the motion state.And lubricate when necessary main standand side stand shafts check of the motion state.And lubricate when necessary l...

  • Page 13

    Front and rear brakes 1.Front and rear brake lever check whether the front and rear brake lever have proper free stroke and make adjustment when necessary. Before riding, carry out a checking and confirmation for brake performance while the motorcycle is running at low speed. 2. Check of brakes when...

  • Page 14

    Air filter air filter can prevent dust entering into the engine. But if the air filter is not properly maintained, dust will still enter into the engine. So the air filter should be regularly cleaned for the in case you run your motorcycle in a dusty, muddy or damp environment, you should check or c...

  • Page 15

    The rider with one passenger,front tire: 175kpa rear tire: 225kpa motorcycle load has an absolute effect to various characteristics of the motorcycle itself, such as operation and control, braking, performance and even safety. Articles, if loaded, must be tightly tied and must not get loose. The hea...

  • Page 16

    Inner tube has been properly installed. For ensuring optimum tire performance, lengthening used life and enabling safe operation, each of the following items should be carefully observed: 1. Before riding your motorcycle, check if the tire is with crackles,folding or warping.If any abnormality has b...

  • Page 17

    Main points for motorcycle using and riding before riding this motorcycle, make sure that you are fully familiar with each of the operation controls and functions of the motorcycle. Should there be any item that you do not fully understand, contact your dealer from whom the motorcycle was originally...

  • Page 18

    Avoid any urgent or sudden braking, otherwise it will make the motorcycle slide or overturn carefully apply force to the brake so as to prevent any motorcycle direction deviation, improper braking will cause motorcycle sideslip. Train rails, iron plates used for road construction and manhole covers ...

  • Page 19

    Change the engine oil, air filter element and gear oil after 500 kilometers running. In case any problems occur with the engine in running-in period, contact with the dealer from whom the motorcycle was originally purchased or with the appointed mainte- -nance station. Parking when parking your moto...

  • Page 20

    Item checking contents the initial 1000 km or one month 3000 km or three months every 3000 km or three mon- -thslateron valve clearance check and set the valve clearance to the specified value when the motorcycle is in cold state. ○ ○ spark plug check the state, adjust the clearance, make cleaning a...

  • Page 21

    Tightness of components check if each of the components of the motorcycle is tightly secured, make adjustments if necessary ○ ○ ○ battery check if the voltage is above 12.8 v, and if the tester pointer is pointing to the green zone .Charge the battery if necessary ○ ○ some proceduces must be check b...

  • Page 22

    1. Upper limit 2. Lower limit engine oil filler cap 2.Replacement of engine oil a). After several minutes of pre-warming, shut down the engine. Place an oil holder under the engine and oil drain bolt d). Clean the oil filter screen and replace it if it is damaged. Engine oil 1.Check of oil amount: a...

  • Page 23

    I). Install the engine oil filler lid and lock it securely. J). Start the engine and pre-warm for several minutes. Check for any engine oil leakage in course of pre-warming. If any leakage is found, shut down the engine immediately and check for the cause. Do not start the engine before engine oil f...

  • Page 24

    3. Replace and lock the crankcase oil drain bolt. Torque for gear oil drain bolt: 23 n m(16.93lb ft) 4. Add gear oil gear oil capacity: 130ml recommend gear oil: sae 85w/140 or api gl-4 gear oil gl-4 is a quality and auxiliary parameter. "gl-5" gear oil can also be used for replacement. Note user's ...

  • Page 25

    If the engine's idle speed cannot be adjusted to the value within the standard specifications, go to the dealer from whom the motorcycle was originally purchased or to the appointed maintenance station for checking. Adjustment of the throttle rotate handle before adjusting the free travel for the th...

  • Page 26

    1. Pull out the gum cover of the regulator. 2. Loosen the fixing nut. 3. Screw in or screw out the regulator till the free travel meets the specification. 4. Lock the fixing nut. 5. Replace the gum cover of the regulator. Gum cover of the regulator adjustment of valve clearance after a certain perio...

  • Page 27

    You may use your hand to screw in 1/2 of the spark plug first. Then tighten the spark plug with a torque spanner to the above torque force. Free travel of front brake free travel of front brake handlebar is 10-20mm (0.394-0.787in). Adjustment of rear brake free travel of rear brake handlebar should ...

  • Page 28

    Inspection of brake fluid amount when brake fluid is not enough, air will enter into the brake system, which will cause failure of the brake. Before riding the motorcycle, check the amount of brake fluid first and fill brake fluid if it is not enough. Please pay attention to the following points whe...

  • Page 29

    Lubrication of throttle valve cable and grip when lubricating cable, apply grease to throttle grip and its joint with the cable at the same time. When lubricating, disassemble the fixing screw of the fueling cable and take out the cable head. Life it up and fill in lubricant. While assembling the th...

  • Page 30

    If there is any damage or poor motion of the front fork, go to the dealer from whom the motorcycle was originally purchased or to the appointed maintenance station for checking and repairing. Check of steering stem check the status of the steering stem regularly. Worn or loose steering stem bearing ...

  • Page 31

    Battery liquid is a kind of noxious and hazardous sub- -stance, which contains sulphuric acid content, so please avoid its touch with skin, eyes or clothes. Extrication method: when it touches the skin, use large amount of water to wash the skin. When drinking it by mistake, drink large amount of bo...

  • Page 32

    Too high water pressure will wash off the lubricant on various parts of the motorcycle, and water will leak into the wheel bearing, which will cause damage to parts. Many expensive repair costs come from improper high pressure washing manner. 4. Wash off plenty of dust with water first, and then use...

  • Page 33

    When using starting motor to start the engine, disassemble the high-voltage wires and earth them so as to avoid the generation of spark. 4. Lubricate all control cables. 5. Use proper support to prop up the front and rear wheel. Then make sure that the motorcycle is in a steady position. 6.Seal the ...

  • Page 34

    Total weight (when the engine oil and gasoline tanks are full ) 251.32lbs engine type cylinder arrangement total working capacity of cylinder cylinder diameter × stroke compression ratio nominal power / relevant rotation speed [kw/(r/min)] max. Torque/relevant rotation speed [n.M(r/min)] idle rotati...

  • Page 35

    Is your motorcycle healthy? It is closely related to the quality of the oil used. Engine oil from original factory engine oil from original factory is a product developed according to the design characteristics of engine. It plays a vital role in such performances as lubrication, power etc. For the ...

  • Page 36

    Maintenance records after completion of the normative maintenance, record the date, odometer readings, name of maintenance man in the provided columns. The additional information "owner check and maintenance" a n d " c o n s t a n t m a i n t e n a n c e " can be added to the below recording sheet. ...

  • Page 37

    Schematic circuit diagram user's manual color code b-black r-red g-green w-white bl-blue gr-grey y-yellow br-brown o-orange n-magenta g/bl-green/blue lg-light green lb-light blue g/y-green/yellow bl/b-blue/black b/w-black/white b/y-black/yellow bl/y-blue/yellow g/r-green/red b/r-black/red br/w-brown...