Www.Qpcom.Com user’s manual qp-3014 broadband router with 4 ports lan and 1 wan.
Table of contents 1. Software installation and configuration.............................................................................. 1 1.1 configuring the ip sharing.............................................................................................. 1 1.2 connecting to the ip sharing...
Ip sharing user’s manual 1. Software installation and configuration 1.1 configuring the ip sharing the ip sharing can be configured to meet various usage conditions. Some of the factory default settings may suit your usage; however, the other settings may need changing. Before using the ip sharing, ...
Ip sharing user’s manual 1.4 setting ip address manually if you want to set your ip address manually, you should know the following default settings of the ip sharing: ip address: 192.68.1.1 (default) subnet mask: 255.255.255.0 if you set your computer’s ip address manually, the address must be on t...
Ip sharing user’s manual (2) click “next”. (3) after reading and accepting the license agreement, click “next. (4) input a user name and organization as information and click “next”. 3.
Ip sharing user’s manual (5) a default destination folder and user information appear. Click “install”. (6) the ip sharing software installation is finished. Click “finish”. (after installation, a shortcut of ”ip sharing” will appear on desktop.) 1.5.1.2 installing winpcap (1) after installation of ...
Ip sharing user’s manual (2) after reading and accepting the license agreement, click “next. (3) read readme information and click “next. (4) after installation, reboot your pc. (recommnded) 5.
Ip sharing user’s manual note: you must connect the wan port of the ip sharing to your adsl or cable modem using a network cable. When your pc is rebooted, the power of ip sharing must be turned on in ready state. 1.5.1.3 configuring the ip sharing executing ip sharing setup if there is any firewall...
Ip sharing user’s manual 1. Select a network interface card (nic). 2. Input the ip sharing’s address (192.168.1.1). (if your computer’s ip address is the on the same subnet as the ip sharing (192.168.1.X), you will not connect to internet.) the ip address can be any number from 2 to 254 that is not ...
Ip sharing user’s manual setting your own password you are given a default password. However, in consideration of safety, it is recommended that you set your own password. If you forget the password, click “reset” on the interface to recover to the default settings. 7.
Ip sharing user’s manual 2. Description of administration interface factory default settings addresses of lan and wan ports the parameters of lan are factory defaults. The defaults are as follows: lan port ip address: 192.168.1.1 subnet mask: 255.255.255.0 dhcp server function: enabled ip address co...
Ip sharing user’s manual static mode (addresses given by isp) name ip address global address give by isp ex. 203.66.81.201 subnet mask addresex. 255.255.255.0 gateway address ex. 203.66.81.254 dns address ex. 203.66.81.251 after successfully logging in, you will enter a main menu soon. There are two...
Ip sharing user’s manual 2.1 quick setup this item provides a user-friendly setup procedure and users follow only several steps to complete the work. Three setup items are provided on quick setup, shown as follows. 2.1.1 dynamic ip setup isp gives a dynamic ip to access internet. You can use this mo...
Ip sharing user’s manual the option is enabled as default. Start ip: you can set up the dhcp server in the blank of lan configuration, a first address configured in the list. End ip: you can set up the dhcp server in the blank of lan configuration, a last address configured in the list. Broadcast st...
Ip sharing user’s manual dns ip: (given by your isp) flow control: to control packet flow for smooth network traffic wan packet tag-aware: to allow the packets sent from wan to be attached with tag- vid (virtual identifier) if you enable this option, the packets sent from wan will have tag-vid; if n...
Ip sharing user’s manual start ip: you can set up the dhcp server in the blank of lan configuration, a first address configured in the list. End ip: you can set up the dhcp server in the blank of lan configuration, a last address configured in the list. Broadcast storm: when a large number of broadc...
Ip sharing user’s manual password: (given by isp) the characters you input in length cannot be more than 20 characters. Confirm: input the password again for confirmation. Mtu: input data for a proper mtu (1492 is a default/maximum.) reducing the packet length helps you to enter a specific website o...
Ip sharing user’s manual address. If you enable the option, dhcp will automatically distribute any ip address to your pc. (the ip sharing is provided with a dhcp server for the lan pc to get ip automatically, and thus each pc is not required to record and set its ip address.) (the option is enabled ...
Ip sharing user’s manual 2.2 advanced setup a further setup items are provided, such as fire wall, virtual server, port forwarding and the like. System status if you want to know the network connection status, you can click “advanced setup” or “status” at the left side of the interface. 2.2.1 lan: (...
Ip sharing user’s manual 2.2.2.1 dhcp configuration wan mac address: a mac address of wan broadcast storm: when a large number of broadcast packets are sent, network traffic jam will occur so as affect the bandwidth. If you enable this function, the broadcast packet flow can be controlled for smooth...
Ip sharing user’s manual dns ip: (given by your isp) flow control: to control packet flow for smooth network traffic wan packet tag-aware: to allow the packets sent from wan to be attached with tag- vid (virtual identifier) if you enable this option, the packets sent from wan will have tag-vid; if n...
Ip sharing user’s manual confirm: input the password again for confirmation. Mtu: input data for a proper mtu (1492 is a default/maximum.) reducing the packet length helps you to enter a specific website or speed up packet transmission. However, if you input wrong data, you may not enter some websit...
Ip sharing user’s manual other setting enable filtering ping packet: when this function is enabled, ping packets can be filtered. Enable forwarding multicast: when this function is enabled, packets can be sent from wan. Drop mac: when this function is enabled, specific mac address packets can be dro...
Ip sharing user’s manual port: to allow you to input a communication port number. If a destination communication port for packets received is exactly the connection port, the received packets will be re-sent to an ip address specified in lan ip. Protocol: communication protocol types are shown in th...
Ip sharing user’s manual 2.2.6 reset you can use “reset” in “advanced setup” to recover to the factory default settings. When you click this item, you will see a prompt menu and you can determine the reset or not on this prompt menu. 2.2.7 exit if you want to exit from this administration interface,...
Ip sharing user’s manual 2.2.8 language this tool provides 3 language interfaces, english, traditional chinese, and simplified chinese. You can select a language you want. 24.
