- DL manuals
- QSC
- Speakers
- K10
- Service Manual
QSC K10 Service Manual - page 46
46
QSC Audio Products, LLC
PC-003311-00 K-SERIES BOARD - TOP SIDE - REV. D
DATE: JULY 22th, 2010
REV.: B
SHEET 1 OF 3
blue
brown
100 - 260vac
MS-10.250-FU
AC LINE FILTER
XF-000376-00
XF-000376-00
XF-000391-00
PFC-IMPROVING
INDUCTOR
RE-000300-NR
MAIN DC VOLTAGE
RECTIFIER & FILTER CAPACITORS
140VDC@100VAC or 340VDC@230VAC
ACTIVE-CLAMP FLYBACK SUPPLY
HI-CUR. SWITCHING
Q13, Q14, XF-SEC
+/-VCC (+/-85V)
SF-PRI, RECTIFIERS, FILTER
CAPACITORS, AND C124+C52
+R166 (REDUCE SECONDARY
GROUND RIPPLE, EFFECTIVELY
INCREASE SNR)
HOUSEKEEPING VOLTAGES
+15V SUPPLY
-15V SUPPLY
VDD1 (+7V SUPPLY)
+12VLOW SUPPLY
VDD (+12V PSU-BIAS)
MAIN +/-85V RAIL
REGULATION (U3, U6, Q15)
POWER SUPPLY CONTROL CIRCUIT
UNDERVOLTAGE
AC DETECTOR
START-UP - PROVIDING CURRENT
FOR CHARGING C145 THROUGH U15
PWM (U15, U3, T1, T3)
J2A&J2B PINOUTS
1: AGND; 2: CH1; 3: CH2; 4: TEMP; 5: FRONT LED
6: AMP-SD; 7: +7V; 8: PGND; 9: -15V; 10: +15V
J5 PINOUTS
1:
2:
FAN+;
FAN-
J6 PINOUTS
1: +5V; 2: VOL; 3: GND
INPUTS & SIGNAL PROCESSING
SIG. PRE. LED
INPUT A, 2-WAY
LINE IN B
J10, J11,
J12, U14:A
SIGNAL
PRESENCE
LED - INPUT B
2-WAY:
EXT SUB/NORM/DEEP
LF SW
GAIN B
FAN SPEED
CONTROLLER
REMOTE
GAIN
GAIN A
2-WAY
+/-15V_D
FRONT LED
SW
2-WAY: HF SW
VOCAL BOOST/FLAT
STATUS INDICATORS
RED: LIMIT
GREEM: STBY
BLUE: POWER
MIC/LINE SW
2-WAY
CLOCK
EEPROM
DSP
+3.3VD
LINE OUT (U17:A)
(POST GAIN - MIX)
PRE-EMPHASIS (U17:B):
10dB @ 5K HZ
LINE OUTS
(POST DSP)
U19:A = CH1
U19:B = CH2
+1.8VD
LINE IN B
J8, J9,
U14:B
SUB: POLARITY SW
NORMAL/REVERSE
SUB: MODE SW
NORMAL/DEEP
MIC LED, 2-WAY
SELF-OSCILLATING CLASS-D AMPLIFIER
CH2 PWM
U4, F(IDLING) = 400k Hz
TEMP-TO-VOLT
SENSOR U9
CH1 PWM
U2, F(IDLING) = 400k Hz
CH2:
GATE DRIVE U5,
HI-CUR. SWITCHING Q2 & Q3,
OUTPUT FILTER NETWORK L1 & C34
CH2 HF 1ST.
ORDER FILTER
CH2 ZOBEL
NETWORK
CH1 ZOBEL
NETWORK
FRONT
LED
CH1:
GATE DRIVE U7,
HI-CUR. SWITCHING Q4 & Q5,
OUTPUT FILTER NETWORK L2 & C35
11.2 PCB image with notes (all models)
Summary of K10
Page 1
Product model: k8, k10, k12, ksub document #: td-000487-00 initial release: february 2015 revised release: revision: a service manual qsc audio products, llc costa mesa, california, usa www.Qsc.Com k series.
Page 2
2 qsc audio products, llc.
Page 3: Table of Contents
3 td-000487-00 k series service manual table of contents 1. Introduction ..................................................................................................................................................................................5 1.1 restriction of hazardous substances directi...
Page 4
4 qsc audio products, llc qsc audio products, llc technical services group 1665 macarthur blvd. Costa mesa ca 92626 usa k series powered loudspeakers service manual copyright © 2014 by qsc audio products, llc. All rights reserved. Qsc and the qsc logo are trademarks of qsc audio products, llc in the...
Page 5: 1. Introduction
5 td-000487-00 k series service manual 1. Introduction 1.1 restriction of hazardous substances directive (rohs) qsc k series loudspeaker products are manufactured to conform to the european union’s rohs directive, which reduces the amount of hazardous substances allowed in products for sale within i...
Page 6
6 qsc audio products, llc 1.5 the well-equipped service bench hardware and software • personal computer (pc) running windows® 7 or newer operating system with available usb2.0 or newer port • total phase aardvark i2c host adapter (for programming) • digital multimeter (dmm) • oscilloscope • audio si...
Page 7: K Series
7 td-000487-00 k series service manual 2. Product specification and images 1 for comparison purposes and in accordance with common industry practice, maximum peak spl specifications are theoretical calculations based upon transducer sensitivity and peak available amplifier power. 2 independent of li...
Page 8: 3. Firmware
8 qsc audio products, llc 3. Firmware very infrequent dsp firmware updates have occured to k series loudspeakers during production. While firmware can be up- dated from the programming header using an aardvark i2c programmer, it’s not recommended and almost never needed to perform updates on the dsp...
Page 9
9 td-000487-00 k series service manual 3.2 firmware programming instructions warning if the instructions are not followed carefully, there is a possibility that the amplifier inside the loudspeaker will stop work- ing. Because house of k loudspeakers use dsp technology, all audio signals are routed ...
Page 10
10 qsc audio products, llc programming a house of k loudspeaker in order to program the loudspeaker with new firmware you must open the correct k programmer utility that works with your windows operating system. To find out what type of operating system you have, go to the system icon under control ...
Page 11: 4.1 Series Description
11 td-000487-00 k series service manual 4. Operational description 4.1 series description converging our expertise in loudspeaker, amplifier, and digital signal processing technologies, qsc has created a spectrum of active loudspeakers designed with one common goal - accurate acoustical performance ...
Page 12: 4.3 Ksub
12 qsc audio products, llc 4.3 ksub the ksub is a dual-12” bandpass design, constructed of premium birch. The wood enclosure is texture painted with a water-based acrylic paint color ral 9011. A single large port sits behind the front panel. The two transducers are mounted vertically on a piece a wo...
Page 13
13 td-000487-00 k series service manual class d amplifier each of the bop amplifiers is a type of class d amplifier called ‘self-oscillating’, as opposed to a class d amplifier that requires a clock to switch. Self-oscillating class d amplifiers create a pwm signal solely by using feedback; although...
Page 14
14 qsc audio products, llc when in off the front led is always off. By setting this switch to limit, the led is normally glows dimly but becomes bright when the dsp is limiting the amplifiers, giving some feedback to the loudspeaker operation from the front of the system. On 2-way systems, hf and lf...
Page 15: 5.1 Bucket of Power
15 td-000487-00 k series service manual 5. Top-box disassembly instructions to reduce the number of pages in this service manual, all top-box k-series loudspeakers have been combined into one section. The k10 powered loudspeaker is used as an example for these generic disassembly and repair procedur...
Page 16: 5.2 Front Grille
16 qsc audio products, llc 5.2 front grille removal 1. Remove the four screws that attach the front grille to the baffle. 2. Using a putty or butter knife, pry the grille outward and remove it. If the grille is stuck, gently pry along the sides in multiple locations until the grille becomes loose en...
Page 17
17 td-000487-00 k series service manual 4. Set the baffle assembly face down on a work surface. 5. Gently place the main enclosure assembly on top of the baffle assembly, paying close attention to the orientation. If possible, connect the molex connector to the bop. Note: connecting the wiring harne...
Page 18
18 qsc audio products, llc 5.5 low frequency transducer the lf transducer can be removed and reinstalled without removing the baffle. Removal 1. Follow the removal instructions in “5.2 front grille” on page 16. 2. Place the speaker on it’s back (or in monitor wedge posi- tion) so the lf transducer d...
Page 19
19 td-000487-00 k series service manual rubber feet removal and installation notes • rubber feet are secured to the enclosure with machine screws (on the exterior of the enclosure) and nuts (on the interi- or of the enclosure). • access to the interior of the speaker assembly is required to remove a...
Page 20: Procedures
20 qsc audio products, llc 6. Ksub disassembly and repair procedures 6.1 bucket of power removal 1. Remove the 10 screws along the outer perimeter of the bop. 2. Partially remove the amplifier module out of the cabinet as seen in figure 6.1. Note: occasionally the module will be stuck to the cabinet...
Page 21
21 td-000487-00 k series service manual 4. Partially lift the transducer out of the cabinet. 5. Disconnect the fastons from the transducer’s positive and negative terminals. 6. Lift and rotate the transducer out of the rear bop cutout hole. It will barely fit. Installation 1. Place the cabinet assem...
Page 22
22 qsc audio products, llc threaded pole mount removal and installation notes • threaded t-nuts are installed in the cabinet for the threaded pole mount to secure to • remove the four machine screws and lift the threaded pole mount out of the cabinet. • verify that any new threaded pole mount has ga...
Page 23: Procedures
23 td-000487-00 k series service manual 7. Bop disassembly and repair procedures 7.1 faceplate removal 1. Remove the 10 screws around the perimeter of the bop. These screws secure the faceplate to the main bucket. 2. Partially lift the faceplate assembly out to gain access to the ribbon cable wire t...
Page 24: 7.2 Psu/amplifier Board
24 qsc audio products, llc 7.2 psu/amplifier board removal 1. Remove the faceplate assembly to gain access to the psu/amplifier pcb. Follow removal instructions in “7.1 faceplate” on page 23. 2. Remove all screws that secure the psu/amplifier pcb to the bucket chassis. 3. Remove the rectangular plat...
Page 25: 7.3 Input/dsp Board
25 td-000487-00 k series service manual 7.3 input/dsp board removal 1. Remove the faceplate assembly for easy access to the input/dsp pcb. Follow removal instructions in “7.1 faceplate” on page 23. 2. Remove all screws securing the xlr and rca connectors to the faceplate. 3. Remove all screws securi...
Page 26: 8. Testing
26 qsc audio products, llc 8. Testing 8.1 requirements hardware • digital multimeter (dmm) • oscilloscope • audio sine wave generator • spl meter • soldering iron • k family test adapter • distortion analyzer (audio precision recommended) • class d output filter for distortion analyzer 8.2 bucket of...
Page 27
27 td-000487-00 k series service manual step 1: power up sequence this test is meant to verify the proper power up sequence. If the bop’s standby or power leds continually blink during power up, there may be an issue with the amplifier’s power supply or output section. 5. Disconnect all xlr, 1/4”, o...
Page 28
28 qsc audio products, llc 5. Adjust the mode switch to “deep”. Verify a slight increase in output voltage on the lf channel. 6. On k8/k10/k12 models, adjust the mode switch to “ext sub”. Verify a decrease in output voltage on the lf channel. 7. Apply a 500 mvrms, 6 khz sine wave signal. Using a dmm...
Page 29: 8.3 Loudspeaker Testing
29 td-000487-00 k series service manual 5. Apply an 8 ohm load to channel 1 only. Follow step 4 again, except test for power this time. A power graph is provided below. 6. Disconnect channel 1’s load. Apply an 8 ohm load to channel 2. Follow step 4 again, except test for power this time. 7. Test com...
Page 30
30 qsc audio products, llc step 2: measuring sensitivity (sound pressure level) 1. Set the frequency of the sine wave generator to 100 hz. 2. Hold the spl meter 1 meter in front of the loudspeaker, directly on axis with its centerline. Measure and take note of the sound pressure. 3. Gradually adjust...
Page 31: 9. Troubleshooting Guide
31 td-000487-00 k series service manual 9. Troubleshooting guide 9.1 general tips and tricks testing the line filter components for open circuit in two measurements the components in the line filter (l11, l12, l13, r140, f1) and the bridge rectifier (br1) can all be checked in two measurements taken...
Page 32
32 qsc audio products, llc amplifier section tips • a quick check of the amplifier feedback path can be done by measuring resistance from the switching node (q2 source and q3 drain, for example) back to the comparator inverting input; it should be about 11.3kΩ. • you may check for amp switching by l...
Page 33
33 td-000487-00 k series service manual 9.2 line filter - broken components (bop) pcb flex/vibration issues seem to cause more broken-component failures in the k12 than in the other k series models. Most common are component leads that break between the base of the component and the pcb. Most vulner...
Page 34
34 qsc audio products, llc 9.3 broken capacitor c45 (bop) pcb flex and vibration issues can also cause the leads on a large electrolytic capacitor, c45, to break. While the amplifier can idle perfectly fine and play music at low power levels with the capacitor broken, the bop will power cycle under ...
Page 35
35 td-000487-00 k series service manual 9.5 amplifier section, mosfet failure (bop) while not a common failure due to the dsp limiting and protecting the amplifier section from being over-driven, the mos- fets in the amplifier section can fail in certain conditions. For example, if the lf or hf tran...
Page 36
36 qsc audio products, llc 9.6 power supply, mosfet failure (bop) the most common psu failure is a failed q13 or q14 mosfet. The failure can cascade down further to gate-drive compo- nents. In some cases, the psu will not start due to a pwm controller u15 failure. Symptoms: • no power • the psu atte...
Page 37: 9.7 Fan Behavior
37 td-000487-00 k series service manual 9.7 fan behavior there may not be a problem with the fan itself due to firmware changes. Please see “3.1 firmware revisions and program numbers” on page 8. On newer models the fan does not turn on until the bop reaches a high temperature condition. On older mo...
Page 38: 9.9 Front Led
38 qsc audio products, llc • if the faston connector was disconnected from the transducer terminal, it’s recommended to crimp a brand new faston connector. For the lf green and green/black wire, use a 0.205” or 5.21 mm female, 14–16 awg, insulated straight faston. For the hf yellow and yellow/black ...
Page 39: 9.10 Transducer Issues
39 td-000487-00 k series service manual 9.10 transducer issues there are many different types of failures for transducers in k series loudspeak- ers. The most common issues found are the following: spider becomes unglued from the frame, cone tears near the surround, burnt voice coil (because of a bo...
Page 40: 9.11 Broken Baffle
40 qsc audio products, llc 9.11 broken baffle this applies to top-box models only. Though not a common failure, the mounting point where the baffle is secured to the main enclosure can break the abs plastic mounts. Symptoms: • very distorted sound • air leaking around the edges of the baffle failure...
Page 41: 10. Service Updates
41 td-000487-00 k series service manual 10. Service updates 10.1 inductor reinforcement, l13 please read qsc service bulletin kse0001 for more information regarding the inductor reinforcement. New k-series models have changed l13 to a 6-pin inductor for added stability on the board. Summary within t...
Page 42
42 qsc audio products, llc sh3: b1 sh3: b2 & c3 2-way 2-way 2-way mic led sub: 0r 2-way 2-way input stage, signal presence, gain, input summing f3 = 72khz inv 2-way line 2-way 2-way 2-way 2-way mic 2-way inv 2-way 2-way sub: 0r mic 2-way sub line sub -inf at bottom +10db at top 2-way 2-way 2-way 2-w...
Page 43
43 td-000487-00 k series service manual sh5: d1 sh2: a3 sh2: a3 = ((1.13k/2.21k) x 3.3) + 3.3 = 4.99v sh2: c1 hf eq/polarity sub: polarity 21.75db gain overlap sub: 0r top: vocal boost limit 01 deep 01 3rd order, f3 = 30khz tall euro header: 2p2t (sw-111) deep 10 phoenix contact 1771965 a-mstbva 2,5...
Page 44
44 qsc audio products, llc sh5: c1 lm19: temp - vout 25c - 1.570v 45c - 1.327v lo = standby hi = led on temp ch1 +15v agnd -15v pgnd wire trap: molex 52004-1010 ch2 amp-sd front led hf amp in 2-way 2-way ch2 out- prep r159 off board 2-way hf pad 2-way 2-way ch1 out+ ch1 out- sync cap t94-2 60t 21awg...
Page 45
45 td-000487-00 k series service manual sh4: b3 & c4 sh4: c4 & sh3: b4 sh4: b2 & c2 t106-26b 79t 18awg on about 24vac oc = 26.1a = 0.75v +85v -85v off in 30ms +7v total operating current = 32ma gate drive current: (102nc + 40nc) * 200k = 29ma ucc2893 run current = 3ma max ac detector 0.5*960uf*375v^...
Page 46
46 qsc audio products, llc pc-003311-00 k-series board - top side - rev. D date: july 22th, 2010 rev.: b sheet 1 of 3 blue brown 100 - 260vac ms-10.250-fu ac line filter xf-000376-00 xf-000376-00 xf-000391-00 pfc-improving inductor re-000300-nr main dc voltage rectifier & filter capacitors 140vdc@10...
Page 47
47 td-000487-00 k series service manual pc-003311-00 k-series board - bottom side - rev. D date: july 22th, 2011 rev.: b sheet 2 of 3 ch1 switching q4: positive; q5 negative ch2 switching q2: positive; q3 negative temp-to-volt sensor u9: pin1 = v+, pin2 = vo; pin3 = gnd rectifier diodes d33: positiv...
Page 48
48 qsc audio products, llc 12. Component identification 12.1 top-box assembly components part number and description quantity ch-000850-01 handle,,blk,speakers, 2 pa-00024 x -01 grille assy, with logo,blk,,, for k8, use pa-000244-01 for k10, use pa-000245-01 for k12, use pa-000246-01 1 sb-00015 x -t...
Page 49
49 td-000487-00 k series service manual part number and description quantity sp-000182-00 woofer,,,12”,paper,ferrite,k12/kw122 k12 only 1 sp-000184-00 compression driver,,,1.75”,petp,neodymium,k/ kw series same hf transducer for k8/k10/k12 1 wp-00331 x -00 pcb assy,universal supply includes psu/amp ...
Page 50: 12.3 Bop Components
50 qsc audio products, llc part number and description quantity wp-003314-00 pcb assy,,ksub,,universal supply 1 wp-003310-00 chassis assy,main,ksub,,universal supply 1 12.3 bop components part number and description quantity co-000436-00 plug,euro,3 pos,male,grn 1 co-000386-00 jack,iec,3 pos,female,...
Page 51
51 td-000487-00 k series service manual part number and description quantity re-000300-nr ntc,2.5 ohms,8 amps,,,inrush limit 90j 1 sw-000088-gp rocker power switch 1 wp-000367-00 fan assy,,bop-2ch,, 1 xf-000376-00 inductor,common mode,toroid,4m- h,bop,,50/60hz 6.3a 2.
Page 52: 13. Exploded View Drawings
52 qsc audio products, llc 13. Exploded view drawings 13.1 k8 exploded view item # part number description qty 1 ch-001153-01 grille, w/no logo, blk, k8, 1.0mm (assembly available) 1 2 ch-000850-01 handle, , blk, speakers, 1 3 ch-001142-01 threaded insert, m5, steel, blk oxide, , 4 4 ch-000870-00 pl...
Page 53
53 td-000487-00 k series service manual 13.2 k10 exploded view item # part number description qty 1 ch-001152-01 grille, w/no logo, blk, k10, 1.0mm (assembly available) 1 2 ch-000850-01 handle, , blk, speakers, 2 3 ch-001142-01 threaded insert, m5, steel, blk oxide, , 2 4 ch-000870-00 plate, handle ...
Page 54
Qsc audio products, llc 13.3 k12 exploded view wp-003304-01.Drw as stored from pdmlink via productview march 26, 2012 11:40am drawing release level: production user name: denise delarm.
Page 55
55 td-000487-00 k series service manual item # part number description qty 1 ch-001151-01 grille, w/no logo, blk, k12, 1.0mm (assembly available) 1 2 ch-000850-01 handle, , blk, speakers, 2 3 ch-001142-01 threaded insert, m5, steel, blk oxide, , 2 4 ch-000870-00 plate, handle backing, , k-series, 4 ...
Page 56
Qsc audio products, llc 13.4 ksub exploded view item # part number description qty 1 ch-000850-01 handle, , blk, speakers, 2 2 ch-000870-00 plate, handle backing, , k-series, 4 3 ch-000889-00 pole mount, threaded, m20, ksub, 1 4 ms-000074-gp acoustic wool, 200x600x30, , , 4 5 ms-000259-gp caster, sw...
Page 57: 14. Replacement Parts
57 td-000487-00 k series service manual 14. Replacement parts 14.1 fg-003300-01 (120v) or fg-003320-01 (230v), k8 part number description qty. Reference comment co-000436-00 plug, euro, 3 pos, male, grn 1 lb-000747-00 label, grille tag, , k8, 1 pm-000270-gp polybag manual, 240x360x0.05, , , , 1 pm-0...
Page 58
58 qsc audio products, llc part number description qty. Reference comment pl-000857-01 gasket, belt, baffle/bucket, k8, , blk, 1 qd-000312-gp led, 3mm, blue sp, slr343bb t 225419 rohm, , , 1 sb-000073-01 bucket, , k8, , blk, 1 not available for purchase sb-000076-01 baffle, , k8, , blk, 1 use baffle...
Page 59
59 td-000487-00 k series service manual part number description qty. Reference comment ms-000480-00 felt pad, pole mount, k-series, , 6 ms-000496-00 spacer, led, , , 1 ms-000543-00 gasket, pe600mm x 10mm x 1.0mm thk, , , 2 ms-000593-00 strip gasket, , 5x500, eva, , 0 ms-000604-00 gasket, strip, k-se...
Page 60
60 qsc audio products, llc part number description qty. Reference comment pm-000447-00 polybag, , , k10/k12, 870x845x.05mm, 1 td-000276-00 hookup drawings, k-series, 1 td-000337-00 warning sheet, pwrd amp/pwrd loudspeaker, 1 wc-000361-gp power cord, 120v, iec v-lock, 18awg, 3m, , nema 5-15, , 1 wc-0...
Page 61
61 td-000487-00 k series service manual part number description qty. Reference comment sc-000303-00 scr, phh, pnh, tpg, plastite, , , , m4, 12 l, stl, blk, zinc cr3, 8 sc-000304-00 scr, phh, pnh, tpg, plastite, , , , m4, 18 l, stl, blk, zinc cr3, 8 sc-000305-00 scr, phh, pnh, tpg, plastite, , , , m5...
Page 62
62 qsc audio products, llc part number description qty. Reference comment ca-110001-10 100pf, 5 pcnt, 500v, mica, dipped, 2 c126, c127 ca-110002-30 100pf, 5 pcnt, 50v, ceramic npo, 0805, 4 c75, c76, c77, c78 ca-112001-30 120pf, 5 pcnt, 200v, ceramic np0, 0805, 12 c1, c19, c20, c22, c28, c29, c30, c3...
Page 63
63 td-000487-00 k series service manual part number description qty. Reference comment ic-000413-30 driver, mosfet half bridge, irs20957, smt, 2 u5, u7 ic-000420-30 voltage regulator, +3.3v, ncp1117st33, sot223, 1 u8 ic-000425-30 opto coupler, transistor output, moc205r2v-m, smt, vde approval 1 u3 i...
Page 64
64 qsc audio products, llc part number description qty. Reference comment re-110002-30 1.00k, 1 pcnt, 1/10w, thick film, 0805, 100v 9 r158, r167, r18, r20, r21, r24, r29, r7, r87 re-111301-30 1.13k, 1 pcnt, 1/10w, thick film, 0805, 100v 12 r106, r107, r163, r164, r171, r177, r23, r25, r30, r31, r73,...
Page 65
65 td-000487-00 k series service manual part number description qty. Reference comment pm-000444-00 insert, top, , ksub, , 120v 1 pm-000445-00 insert, bottom, , ksub, , 120v 1 pm-000449-00 polybag, , , ksub, 1120x500x.04mm, 1 pm-000491-00 insert, , , ksub, , 1 pm-000516-00 bag, , polypropylene, k-se...
Page 66
66 qsc audio products, llc part number description qty. Reference comment ch-000885-00 panel, input, bop-2ch, ksub, 1 ch-001025-00 shield, line filter, short, kw series, 1 co-000386-00 jack, iec, 3 pos, female, locking 1 lb-001062-00 label, rcm logo, regulatory certification mark, , (australia & new...
Page 67
67 td-000487-00 k series service manual part number description qty. Reference comment ca-410027-10 0.1uf, 5 pcnt, 100v, film, box style, 2 c109, c119 ca-468005-10 0.68uf, 5 pcnt, 100v, film, box, 3 c125, c34, c35 ca-468006-00 0.68uf, 5 pcnt, 250v, polypropylene, box, 2 c116, c149 ca-468007-00 0.68u...
Page 68
68 qsc audio products, llc part number description qty. Reference comment qd-000102-30 diode, 75v, 0.075a, , imbd4148, sot-23, 4ns 12 d1, d13, d15, d16, d2, d22, d25, d27, d35, d40, d45, d7 qd-000103-30 transistor npn, 40v, 0.2a, 0.2w, mmst3904, sot-23, 5 q1, q11, q12, q17, q6 qd-000104-30 transisto...
Page 69
69 td-000487-00 k series service manual part number description qty. Reference comment re-220002-30 20.0k, 1 pcnt, 1/10w, thick film, 0805, 100v 9 r104, r105, r111, r112, r84, r96, r97, r98, r99 re-229402-30 29.4k, 1 pcnt, 1/10w, thick film, 0805, 100v 1 r150 re-256002-10 56k, 5 pcnt, mini-1w, metal...
Page 70: Contact Information
Contact information service manuals and other service documents are available for download from www.Qscservice.Com. If you need any further information regarding this service procedure, please contact qsc technical services at the addresses or numbers below. Telephone: 1-800-772-2834 (within usa onl...