1. DL manuals
  2. QSC
  3. Stereo System
  4. Q-SYS Core 250i
  5. User Manual

QSC Q-SYS Core 250i User Manual

Other manuals for Q-SYS Core 250i: Specification, User manual
Manual is about: Networked audio and control processor and input and output device; Networked audio and control processor and input and output device

Summary of Q-SYS Core 250i

  • Page 1

    Td-000347-00-a *td-000347-00* ™ type 2 hardware user manual core 250i — networked audio and control processor and input and output device core 500i — networked audio and control processor and input and output device.

  • Page 2: Lithium Battery  Arninn

    2 td-000347-00-a explanation of terms and symbols the term “warning!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death. The term “caution!” indicates instructions regarding possible damage to physical equipment. If these ...

  • Page 3: Fcc Statement

    3 td-000347-00-a fcc statement note!: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. Note!: these limits are designed to provide reasonable protection against harmful interference in a residential installation. T...

  • Page 4: Rohs Statement

    4 td-000347-00-a rohs statement the following chart is provided for product use in china. Q-sys™ core 250i 系列, q-sys core 500i 部件名称 (part name) 有毒有害物质或元素 (toxic or hazardous substances and elements ) 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 电路板组件 (pcb assemblies) x o o o o o 机壳装配件 (...

  • Page 5: Connections

    5 td-000347-00-a connections ac power cord insert the molded receptacle of the ac power cord into the ac power inlet on the back of the q-sys product. (figure 1) plug the ac line connector into an ac outlet. The power supply on the q-sys cores accepts 100 — 240 v, 50 — 60 hz. If a different type of ...

  • Page 6

    6 td-000347-00-a minimum system requirements for q-sys™ designer q-sys designer is the software you use to create the designs for a q-sys system. After your system is designed, tested and deployed on the core, q-sys designer is not required for that system to operate. Q-sys designer runs in a pc env...

  • Page 7: Quick Start Nuide

    7 td-000347-00-a quick start nuide this quick start guide is intended to give a high-level procedure for getting a simple q-sys system connected, running a q-sys design, and passing audio. The following procedure assumes that you have a q-sys designer file with components properly connected, but not...

  • Page 8: Overview

    8 td-000347-00-a overview q-sys™ is an integrated system audio solution. The dsp is centralized to allow faster development and deployment of new features, and requires fewer hardware changes as well. Q-sys has been designed around four major criteria: sonic quality, reliability, power and flexibili...

  • Page 9

    9 td-000347-00-a qsc dataport amplifiers qsc dataport amplifiers (powerlight™, cx, pl2, dca, and pl3) can be used in a q-sys system to communicate with the q-sys dataport card and provide critical telemetry information and protection for both the amplifier and any loudspeaker. With qsc loudspeaker c...

  • Page 11

    11 td-000347-00-a rear panel core 500i 1. Eight audio i/o bays — accepts q-sys type 2 audio i/o cards 2. Gpio a and gpio b female da-15 connectors for q-sys control i/o 3. Video out — hd-15 female connector for future use 4. Video out — dvi female connector for future use 5. Rs-232 — de-9 male conne...

  • Page 12

    12 td-000347-00-a q-sys™ i/o card remove and replace procedure this procedure is for q-sys type 2 i/o cards only. Card installation should only be done by a trained and qualified technician. Tools • phillips screwdriver • esd grounded wrist strap • 1/4” hex driver/socket (not shown) for replacing q-...

  • Page 13

    13 td-000347-00-a note!: when you connect the ribbon cable to the core main board be sure that you connect it to the proper connector. The connectors on the core main board are identified by the slot letters a through h. 9. When replacing the blank card with an i/o card, the new ribbon cable must al...

  • Page 14

    14 td-000347-00-a q-sys™ npio signal specifications npio pin assignments db15 pin signal name signal type description 1 rno relay contact relay - normally open 2 rnc relay contact relay - normally closed 3 gpio1 normal current gpio pin 4 gpio3 normal current gpio pin 5 power power +12 v dc 6 gpio5 h...

  • Page 15

    15 td-000347-00-a q-sys type 2 system hardware specifications core 500i core 250i description system processor, control engine, and input and output device system processor, control engine, and input and output device front panel controls lcd page forward momentary switch unit id button momentary sw...

  • Page 16

    16 td-000347-00-a core 500i core 250i accessories included 6ftul/csa/ieclinecord•rubberfeet•usermanual•software cd•optionalaudioi/oshipkit 6ftul/csa/ieclinecord•rubberfeet•usermanual•software cd•optionalaudioi/oshipkit 2 the maximum number of local channels a core can have is 128 in and 128 out (64 ...

  • Page 17

    17 td-000347-00-a i/o cards (dataport out, aes3) dataport output codp4 aes3 input/output caes4 description four audio output channels (2 dataports) for connection to dataport equipped qsc amplifiers four input and four output channels of aes3 digital audio performance dynamic range unweighted dynami...

  • Page 18

    © 2012 qsc audio products, llc. All rights reserved. Qsc and the qsc logo are registered trademarks of qsc audio products, llc in the u.S. Patent and trademark office and other countries. Q-sys and intrinsic correction are trademarks of qsc audio products, llc. Amd is a trademark of advanced micro d...