Td-000227-00 rev.B *td-000227-00* isis wideline loudspeaker user manual manual del usuario para los altavoces isis wideline manuel de l'utilisateur des haut-parleurs isis wideline isis wideline-lautsprecher – benutzerhandbuch isis wideline 扬声器用户手册 wl2102 cored composite enclosure wl2102-w birch plyw...
2 important safety precautions install in accordance with qsc audio product's instructions and under the supervision of a licensed professional engineer. Warning! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets...
3 introduction the wideline loudspeaker system has been designed to pro- vide a compact system that has unique power handling, fre- quency response. Its primary uses include ballrooms, theatres, night clubs, houses of worship, and small to medium size events for the corporate and industrial markets....
4 tri amp/bi amp switch tri amp: shading network is not applied (shading must be provided by upstream signal processing). Connect the full- range input signal to pins 1+ and 1-, connect the shaded (pro- cessed) signal to pins 2+ and 2-. To flip shaded transducer location, use the mf (unshaded) selec...
5 input connections the input connectors are a pair of neutrik nl8's wired in parallel. Connections for bi amp and tri amp vary, see table 1. The pin designations for the nl8fc cable connector is shown for ref- erence, bottom right. Note! In tri amp mode, the mf (unshaded) select switch position det...
6 rigging rules for suspension •correct use of all suspension hardware and components is imperative in sound system rigging and deployment. •always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits. •research local code...
7 rigging wideline enclosures use a three-point suspension system. The system consists of front, left/right, captive articulated joints and a single rear link bar. Articulation is in 2° incre- ments using the first location on the link bar. With the use of the second location, 1° degree increments c...
8 adjusting the angle between enclosures (splay) the illustration shows the rear pin block of two enclosures joined by the upper enclosure’s rear link arm. Use the first pin location (closest to the end) on the link arm for setting in normalized 2° increments. The left-side example shows two enclosu...
9 fly grid the mounting plate and link bar are located on the bottom side of the frame assembly. Use this link for attaching the rear of the first enclosure. The frame allows for up or down angle options for use with either stacking or suspending. The 4° “normal” locations on the link system will yi...
10 stacking the stacking frame the stacking frame comes with two aluminum i-bars used for aligning and securing the frame to qsc’s 215sb or 215pcm subwoofer. To use the i-bars, simply slide each one into the small frame’s l-track and secure with a stud fitting. Then, turn the frame over (i-bars on t...
11 system specifications (subject to change without notice) configuration: three way, bi amp or tri amp frequency response 1 : 55 - 18,000 hz (+/- 3 db) frequency range: 48 - 20,000 hz (-10 db) sensitivity: lf: 98 db (1w @ 1m) hf: 107.5 db (1w @ 1m) nominal coverage: horizontal: 140 degrees vertical...
12 dimensions- wl2102 and wl2102-w note! Composite enclo- sures have approximately 1° of draft on the enclosure sides; the birch plywood enclosures do not. Handle orientation may vary between composite and plywood enclosures. 20.75” (527mm) 10.75” (273mm) 20.4” (518mm) 7.7” (196mm) 27.5” (699mm) 26....
13.
Qsc audio products, inc. 1675 macarthur boulevard costa mesa, california 92626 usa ©2006 “qsc” and the qsc logo are registered with the u.S. Patent and trademark office. How to contact qsc audio products mailing address: qsc audio products, inc. 1675 macarthur boulevard costa mesa, ca 92626-1468 usa...
