- DL manuals
- QTX Light
- Lighting Equipment
- LS-OPAL
- User Manual
QTX Light LS-OPAL User Manual
Summary of LS-OPAL
Page 1
Version:2.0 this manual contains important laser system safety and operation information. Read and understand all instructions prior to powering on laser unit the first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference..
Page 2: Warning Data
User manual 1 warning data lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety remark and warning statement in the user manual. Read all instructions carefully before operatin...
Page 3: Laser Safety Warnings
User manual 2 laser safety warnings caution avoid direct eye contact with laser 了 light. Never intentionally expose your eyes or others to direct laser radiation. Caution this laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes. Caution it is ...
Page 4
User manual 3 laser safety and operating instructions stop and read all laser safety data laser light is different from any other light source witch you may be familiar. The light from this product can potentially cause eyes injury if not set up and used properly. Laser light is thousands of times m...
Page 5: Laser Exposure Warning
User manual 4 z after set up, and prior to public use test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emissio...
Page 6: Laser Emission Data
User manual 5 laser safety label reproductions the label indicates the laser beam output aperture caution – class 3b laser radiation, when open, avoid exposure to beam laser radioation avoid exposure to beam class 3b laser product. Laser emission data * as measured under iec measurement conditions f...
Page 7: Laser Compliance Statement
User manual 6 laser compliance statement this laser product complies with en/iec 60825-1 ed 2,2007-03,and us fda/cdrh flpps via the terms of laser notice no.50 dated june 24,2007. General safety instructions every person involved with installation and maintenance of this device have to z be qualifie...
Page 8
User manual 7 cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Z it is essential to connect the yellow/green conductor to earth. Z the electric connection, repairs and servicing must be carried out by a qualified employee. Z do not switch the fi...
Page 9: Before Operation
User manual 8 before operation unpacking instructions caution! Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspecti...
Page 10
User manual 9 channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the source voltage matches the fixture’s requirement. The unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections be required they must be ...
Page 11
User manual 10 building a serial dmx-chain z if you are using the standard dmx-controllers, you can connect the dmx-output of the controller directly with the dmx-input of the first fixture in the dmx-chain. If you wish to connect dmx-controllers with other xlr-outputs, you need to use adapter cable...
Page 12
User manual 11 proper laser set up & usage this fixture has been designed to be hung. It is recommended for safety purposes, your lighting effect are properly mounted using a suitable hanging clamp and safety cable. Items appropriate for safe and effective mounting are easily sourced from your light...
Page 13: Rigging The Fixture
User manual 12 rigging the fixture z the installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.. Z the installation must always be secured with a secondary safety attachment, e.G. An appropriate catch net....
Page 14: Product Overview
User manual 13 product overview z this device has left out premise in absolutely perfect condition. In order to maintain this condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual. Z the manufacturer will not a...
Page 15
User manual 14 front panel no name function 19 power main power indicated led. Red is on. 20 ilda / dmx red is ilda connected, green is dmx model. 21 music/auto music/auto indicated led. Red is music mode and green is auto mode. 22 mic /audio mic/audio indicated led. Red is mic activated music mode ...
Page 16
User manual 15 rear panel no name function 1 switch switch on and off the power 2 mains input with socket and integrated fuse holder 3 key switch make sure the professional person use 4 urgent and safe switch switch off the laser manually if error occurs 5 dmx output 3pin female xlr port，using for d...
Page 17
User manual 16 ilda / hardware setting panel no name function 11 x size y size the size of x / y axis adjustment 12 x mirror y mirror x / y axis mirror setting (it could be done by lcd control panel as well) 13 audio audio input. Turn the knob to adjust the audio respond sensitivity. 14 mic micropho...
Page 18: Control & Function
User manual 17 control & function z regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use. Z do not switch the unit on and off in short time intervals z always unplug the unit when it is not used for a longer time. Or before replaci...
Page 19
User manual 18 operation auto show 1 z press func to enter mode option z till to auto show 1 shown on lcd monitor. The laser is set at auto show 1 standalone mode and it will play the preprogrammed show until next setting is changed. Auto show 1 is fast and hot show which is better for disco. Z pres...
Page 20
User manual 19 music show 1 z press func to enter mode option z till to music show 1 shown on lcd monitor. The laser is set at music show 1 standalone mode and it will play the preprogrammed show until next setting is changed. Music show 1 is fast and hot show which is better for disco. Z press ente...
Page 21
User manual 20 attention when the laser is connected with dmx controlled or under control by dmx signal, the dmx indicated led on front panel is in red. Slave mode z press func to enter mode option z till to slave shown on lcd monitor. Connect master and slave lasers with dmx cable. The slave lasers...
Page 22: Dmx Channels Chart
User manual 21 ilda control mode z this unit has the ilda db25 port, and it can be controlled by the pc, there is auto transform set in the inside of the unit to transform the ilda and preprogrammed show. When connecting by the 25 pin cable, the unit will be control by pc, when disconnect the unit, ...
Page 23
User manual 22 single pattern mode dmx chart channel value description ch 2 laser on/off 000-127 laser off 128-255 laser on ch 3 group 000-255 every 32 for 1 group, total 8 groups. Ch 4 pattern 000-255 every 16 for 1 pattern, total 16 patterns. Ch5 color 000-31 pattern original fixed color none func...
Page 24
User manual 23 ch 10 y axis rolling 000-127 0°~359°fixed pattern rolled 128-191 slow to fast clockwise rolling 192-255 slow to fast anticlockwise rolling ch 11 z axis rotating 000-127 0°~359°fixed pattern rotated 128-191 slow to fast clockwise rotating 128-255 slow to fast anticlockwise rotating ch ...
Page 25
User manual 24 ch6 color 000-005 pattern original fixed color 006-255 color loop from slow to fast ch 7 cliping 000 full pattern without clipping 001-127 0%~99% fixed pattern clipped 128-255 slow to fast pattern clipping ch 8 zooming 000-005 100% full pattern without zooming 005-127 4%~99% fixed pat...
Page 26
User manual 25 096-127 yellow laser projector 128-159 green 160-191 cyan 192-223 blue 224-255 purple ch 17 color 000-005 pattern original fixed color 006-255 color loop from slow to fast ch 18 cliping 000 full pattern without clipping 001-127 0%~99% fixed pattern clipped 128-255 slow to fast pattern...
Page 27
User manual 26 wave effect mode dmx chart channel value description ch 2 laser on/off 000-127 laser off 128-255 laser on ch 3 amplitude 000-255 0%~100% wave amplitude ch 4 frequency 000-255 0%~100% wave frequency ch 5 color 000-31 pattern original fixed color none functions on single color laser pro...
Page 28
User manual 27 pattern list in channel 3&4 dmx 1 2 3 4 5 6 7 8 000-015 016-031 032-047 048-063 064-079 080-095 096-111 112-127 128-143 144-159 160-175 176-191 192-207 208-223 224-239 240-255.
Page 29: Maintenance
User manual 28 maintenance z make sure the area below the installation place is free from unwanted persons during servicing z switch off the unit , unplug the mains cable and wait until the unit has been cooled down. Z housings, fixations and installations spots( ceiling, truss, suspensions) should ...
Page 30
User manual 29 trouble shooting following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting. Z the fixture does not work, no laser and the fan does not work. 1) check the connect power and main fuse. 2) measure the mains voltage on the main...
Page 31: Specifictaions
User manual 30 specifictaions mains input: fuse: total power: x/y axis beam angle: music control: laser power: laser classification: laser safety standard: condition temperature: dmx connections: dmx channels measurement: n weight: ac100~240v, 50/60hz 250v 2a slow blow (20mm glass) 60w ±25° audio / ...