1. DL manuals
  2. QUAD
  3. Subwoofer
  4. C4 - REV 1
  5. Instruction Booklet

QUAD C4 - REV 1 Instruction Booklet

Summary of C4 - REV 1

  • Page 1

    C o n c o u r s e c s e r i e s instruction booklet models c4, c4-16, c4-t, c6, c8, & csub f o r t h e c l o s e s t a p p r o a c h t o t h e o r i g i n a l s o u n d r e v .1.

  • Page 2

    Safety instructions safety first! 1. Pleasereadthismanualfullybeforeinstallingandoperatingthis product. 2. Retainacopyofthismanualforfuturereference. 3. Complywithallwarninglabelsandinstructions. 4. Donotattempttheinstallationofthisequipmentunlessyouare qualifiedtodoso. 5. Protectyourhearingfromhigh...

  • Page 3

    Product description the concourse c series are two-way, high performance ceiling mounted speaker systems designed for distributed music, paging and speech applications. Packaged in pairs (except the c-sub and c-subt) and including all needed mounting accessories, the c series models are complete ven...

  • Page 4

    Product features all models include the following components: • speaker assembly (2) • cover grille with restraint (2) • split c ring backing plate (2) • support rails (4) • plastic paint cover (2) • cardboard cutout template (2) please ensure that you are familiar with all of the parts and how they...

  • Page 5

    Product description concourse c models are complete assemblies ready for installation into both suspended tile ceilings and hard ceilings. A rear mounted termi- nal box allows termination of the speaker wiring to the speaker as well as impedance selection (except c4t and c4-16). Power taps are selec...

  • Page 6

    Concourse c4, c4-8, c4-16, c4-t concourse c6 concourse c8 concourse csub 219mm/8.62” 219mm/8.62” 349mm/13.74” 331mm/13.03” 371mm/14.6” 238mm/9.37” 293mm/11.54” 333mm/13.11” 212mm/8.35” 252mm/9.92” 212mm/10.04” 295mm/11.61” 6.

  • Page 7

    Installation suspended tile ceilings step 1 carefully unpack the contents of the box and ensure that all parts are accounted for before beginning installation. Step remove the tile from the ceiling and place it on a suitable work surface to cut the hole and assemble the speaker. Locate the cardboard...

  • Page 8

    Step 9 step 10 8 step remove the screws holding the terminal cover plate and then remove any knock outs needed to connect the speaker wiring. Step 8 select the appropriate impedance using the push-button switch inside the terminal box if the speaker is part of a low impedance system (except c4t and ...

  • Page 9

    9 installation hard ceilings note: installation into a hard ceiling requires that you first ensure that the location is suitable and that there are no obstacles behind the ceiling material. Use extreme caution when cutting into hard ceilings to avoid severing electrical wiring, heating ducts or wate...

  • Page 10

    10 step lift the speaker into the opening, then using a screwdriver tighten each of the four mounting screws in sequence. Turning the screws in a clockwise direction will cause the mounting clamps to rotate into position then extend down to clamp the assembly to the ceiling. Step 8 set the correct w...

  • Page 11

    From amplifier to next speaker 11 wiring & connections ensure that all wiring is installed in compliance with local laws, codes and convention. Obtain all necessary permits and approv- als and use only cable that is approved for the application and is sized to safely accommodate the load. Models c /...

  • Page 12

    1 for low impedance operation first set the rotary switch to indicate the 4Ω setting. Then remove the terminal cover plate and note the position of the push-button switch. When the switch is in the “up” position it indicates that the system is in 4Ω mode. When the switch is in the “down” position it...

  • Page 13

    1 specifications (c4/c6/c8/csub/c4/16) power handling: c4 models c6 c8 csub c4-16 continuous 25w 50w 75w 100w 25w program 50w 100w 150w 200w 50w peak 100w 200w 300w 400w 100w frequency response: 55hz−20khz 50hz−20khz 45hz−20khz 28hz−500hz 55hz−20khz (-10db) frequency response: 70hz−20khz 70hz−20khz ...

  • Page 14

    R e v .1 f o r t h e c l o s e s t a p p r o a c h t o t h e o r i g i n a l s o u n d © 2006 quad industrial. Quad industrial is a member of the international audio group. Iag america inc. 8440 154th avenue ne · redmond, wa 98052 u s a c o n t a c t : p h + 8 7 7 . 4 4 0 . 0 8 8 8 p h + 4 2 5 . 8 6...