1. DL manuals
  2. QuadBoss
  3. Lawn Mower
  4. QBT11544
  5. Owner's Manual

QuadBoss QBT11544 Owner's Manual

Manual is about: 44” FINISH CUT TRAILMOWER

Summary of QBT11544

  • Page 1

    44” finish cut trailmower owner’s manual 1602 corporate drive, warrensburg missouri 64093 phone 660-747-8183 fax 660-747-8650 model no. Manufacturing quality lawn care equipment since 1945 assembly operation service and adjustment repair parts made in the usa rev 12-016 read and follow all safety pr...

  • Page 2

    Limited warranty the manufacturer’s warranty to the original consumer purchaser is: this product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to b...

  • Page 3

    This safety alert symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the fo...

  • Page 4

    • turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine. • watch for traffic when operating near or crossing roadways. • do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibrati...

  • Page 5

    Od36-deflector decal od45-warning decal od29-danger decal engine serial # od11-no step decal od15-void warranty decal od33-speed decal od55-triangle danger decal (all four deck corners) trailmower serial # safety decals replace decal immediately if damaged. Order by part number from swisher od99125-...

  • Page 6

    Operating your trailmower intended use the 44” trailmower is designed to produce a quality finish cut on lawns, golf courses, etc. It is not intended to clear brush or cut saplings. Your trailmower should be towed behind an atv, golf cart, lawn tractor, or other approved vehicle. It is not designed ...

  • Page 7

    • set vehicle parking brake or chock wheels to prevent accidental rolling. • start engine properly. • slowly, engage blade control. • in a safe environment, i.E. No children, allow blades to rotate and engine to idle for 5 minutes. This breaks in the belts and the engine. • stop mower properly. Enga...

  • Page 8

    • there is approximately 1 ½” to 4 ½” of height adjustment. • rotate height adjust crank handle(s) in a clockwise direction to lift the mower deck. A counter-clockwise direction is used to lower the mower deck. • for best results, see “suggested practice” section. Graduated scales are for reference ...

  • Page 9

    Suggested mowing practices • operate mower engine at full throttle to assure the best cutting performance and maximum material discharge. • allow wet grass to dry. Wet grass will clump and collect under the mowing deck. • mowing should be started with tow vehicle in low gear and increased only as sa...

  • Page 10

    Mower maintenance general recommendations the warranty on this trailmower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodical...

  • Page 11

    Blade care and service for best results cutter blades must be kept sharp. The blades can be sharpened with a few strokes of a file or grinding wheel. Do not attempt to sharpen blades while they are on the cutter. Disconnect spark plug wire before servicing unit. Important: replace blades that have b...

  • Page 12

    Front left right rear fig. 2 fig. 1 slide plastic tube snug against toggle switch. (fig. 5 for details) 12 rotate fan plates as needed..

  • Page 13

    T44 recoil start t44 12 volt start fig. 3 parts not shown wiring configurations 13 wiring harnesses b&s engine (remote start only) wh44chb12v honda engine wh1144h remote option wh44rch pull start w/ b&s engine 10638 toggle/ground wire assembly 9090 blade engage cable 9074 12v b&s manual blade engage...

  • Page 14

    Fig. 4 single point height adjust see details see detail 1 1 4 2 12 11 10 8 7 6 18 17 16 15 14 13 24 23 22 21 20 19 33 32 29 28 27 25 * = use paint code: tc=red, tk=black 31 item # description part # 1 cover - belt 10599* 2 base - motor 4517* 3 bolt - 1/4-20 x 1/2 nb114 4 knob - height adjustment h7...

  • Page 15

    Fig. 5 engine set-up fig. 6 blade set-up item # description part # qty 1 engine - 11.5hp 14468 1 1 engine - 12.5hp 14469 1 2 module - engine mod1* 1 3 valve - oil drain 16000 1 4 bolt - serr flange, 5/16-18 x1 1/4 nb253 4 5 tether - assembly 6736 1 6 bracket - switch 4483z 1 7 switch - toggle, singl...

  • Page 16

    Fig. 7 standard engage item # description part # qty 1 bolt - 1/2-13 x 5 nb155 1 2 bolt - spade, 5/16-18 x 10.5 nb260 1 3 nut - nyloc 5/16-18 nb181 1 4 pivot - engage 4578tk 1 5 nut - 5/16-18 nb210z 2 6 knob - shift b19black 1 7 pivot - engagement 4548tk 1 8 nut - serr flange 5/16-18 nb170 1 9 nut -...

  • Page 17

    1 2 3 4 5 2 6 7 8 item # description part # 1 belt - 74" 4220 2 spring t2sm 3 bracket - spring tension 4593tk 4 brake - arm sub-assembly, left 10591 5 brake - arm sub assembly, right 10590 6 switch - return to neutral 3695 7 bracket - switch 4301tk 8 bolt - serr flange 5/16-18 x 3/4 nb596 8 nut - se...

  • Page 18

    Fig. 11 brake arm configurations 18 item # description part # qty 1 arm - brake 10589tk 1 2 eyebolt - 1/4-20 x 3/4 v139eb 1 3 nut - nylock 1/4-20 nb180 1 4 nut - serr flange 1/4-20 nb524 2 5 bolt - htc 1/4-20 x 1 1/2 nb162 2 6 nut - kep 10-24 nb172 1 7 pad - brake 9039 1 8 screw - 10-24 x 1 1/2 nb71...

  • Page 19

    19 fig. 12 hitch assembly item # description part # qty 1 bolt - u, sq 3/8-16 x 1 5/8" x 2 3/4" 9855 2 2 weldment - "l" hitch 18353tk 1 3 pin - safety hitch 3/8 x 2 1/2 h11 1 4 plug - l hitch h1p 2 5 nut - nyloc 3/8-16 nb182 8 6 tube - hitch 18347* 1 7 bolt - 3/8-16 x 2 1/2 nb221 4 8 washer - 3/8 nb...

  • Page 20: Notes:

    ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ________________...

  • Page 21: Notes:

    ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ________________...

  • Page 22: Notes:

    ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ________________...

  • Page 23

    23.

  • Page 24: Owner’S

    Owner’s manual how to order repair parts: 44” finish cut trailmower each trailmower has its own serial number. Each engine has its own serial number. The serial number for the trailmower will be found on the right hand side of the drive belt housing. The serial number for the engine will be found on...