- DL manuals
- Quadivator
- Lawn Mower
- HyperCut RD62
- Assembly/operators/parts Manual
Quadivator HyperCut RD62 Assembly/operators/parts Manual
Summary of HyperCut RD62
Page 1
!" #$% &&&' ( )! *!+ $""")( ,! ) , #-. /01 )-!& 2. -!& # * 2.
Page 3: Foreword
Foreword you are now the owner of a quadivator hypercut mower. To obtain the best use of your hypercut mower, read this manual carefully. It will help you become familiar with the operation and maintenance of the mower. It is quadivator’s policy to use all research, design and manufacturing improvem...
Page 4
Safety first this symbol, the industry’s “safety alert symbol”, is used throughout this manual and on labels on the machine to warn of the possibility of personal injury. Read these instructions carefully. It is essential that you read the instructions and safety regulations before you attempt to as...
Page 5
Hypercut mower pre-delivery check list check off all items as they are found satisfactory or after adjustments are made: all safety shields and guard are securely in place! All decals are in place and readable! Tighten all hardware – see checking bolt torque in service section. Check and tighten bla...
Page 6: Owner Register
Owner register name address city state/prov mail code model (s) serial (s) date sold – d/m/yr delivery checklist tell the customer not to remove any of the safety shields or guards. Review the hypercut warranty with customer. Safe operation and service. Daily and periodic lubrication and maintenance...
Page 7: Table of Contents
Table of contents --------------------------- 1. Safe operation 2. Introduction .1 specifications 3. Setup .1 mower deck assembly .2 mounting mower to power unit .3 mounting mower to atv .4 removing and re-attaching the mower 4. Operation .1 making the best of your mower .2 cutting height .3 operati...
Page 8: Safe Operation
1. Safe operation this cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Danger 1.1 general operation read, understand, and follow all instructions on the machine and in the manu...
Page 9
Operate machine only in daylight or good artificial light. Do not operate machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Always wear eye protection when o...
Page 10
1.3 children tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Warning keep children out of the mowing area and in the watchful care...
Page 11: 2. Introduction
Check grass catcher components and discharge guard frequently and replace with manufacturer’s recommended parts, when necessary. Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. Check brake operation frequently. Adjust and service as required. Maintai...
Page 12: 3. Setup
3. Setup 3.1 mower deck assembly step 1. Remove the components from the shipping container: 1. The assembled deck. 2. The packaged height adjustment handle. 3. The tower assembly kits, packaged with the height adjustment handle. Step 2. Note the serial number of the deck - it is located as shown in ...
Page 13
3.2 mounting mower to power unit step 1 . Insert the tubes of the power unit into the matching brackets on the mower deck as shown. You may need to manoeuvre the power unit into place by grasping the rear nerf bar and wheeling it into position step 2. Secure the mower deck to the power unit with the...
Page 14
Important do not over-tighten the belt – over-tightening the belt will cause excessive heat build up in the belt and premature belt wear! Step 4. Re-install the deck drive shield. Step 5. It is possible to start the mower at this time, before it is mounted to any atv. If you choose to do so, follow ...
Page 15
This initial fit up – hypercut mower to atv - should take place on a flat hard surface that has enough room to mount the mower to the atv, and then manoeuvre the assembled unit! Step 1 - install the supplied pin – part # 88652 in the atv as shown – place the pin through the top and the large washer ...
Page 16
Step 5 - when the atv contacts the ground with all 4 wheels, and the mower between the atv wheels – shut off the atv and place it in neutral for manual maneuvering. Step 6 – remove the floating hitch (by removing the bolt/pivot – with the swivel and number of holes) – from the hitch tower and attach...
Page 17
Note – the hitch with the swivel can be installed in either the “l – up” or “l- down” positions as shown. What is important is that the floating hitch member is in the horizontal position when installed on your atv! Note – always place this bolt in the rear set of holes (on the tower) when installed...
Page 18
Looping the chain around your frame should be done in a secure place to the frame of the atv, there should be a connection point that is a minimum of 12” inward from the “tower” and as much as possible, the connection point - should be in-line with the tower on the other side. Use the provided d-pin...
Page 19: 4. Operating Section
4. Operating section the quadivator hypercut mower mounted to an atv is designed to produce a quality finish on lawns, golf courses, etc. It is not designed to clear brush or to cut saplings. Your hypercut mower should be attached to an atv in the manner described in this manual and should not be us...
Page 20: 5. Maintenance
Check the pneumatic wheels on the hypercut mower daily. They should have 45psi. Cutting height can be adjusted from 1 – 3.75 inches (25 to 95 mm) to set the cutting height, operate the rhs height control lever. On thick springy grass or soft ground, the mower’s rollers may sink into the ground givin...
Page 21
8 ensure hitch security pin is in place - through the atv hitch pin x 9 ensure the deck restraining chains are secure – both ends x 10 ensure that hitch assembly on the mower is secure and moves freely x 11 remove any debris build up on engine cooling air intake. X 11 shut fuel off after usage sessi...
Page 22
To remove the blade(s) from the mower , lift one side of the mower up in the air and block it securely. Wedge a block of wood between the blade and the mower deck housing of that blade to prevent the spindle from rotating while the blade retaining bolt is removed. Loosen the blade by turning the bla...
Page 23
If the deck belt needs replacing, at this point in the disassembly replace the deck belt! Information place the new deck drive belt in pulley in the front, then loop it through the idlers on the rear section of the power unit and attach around the drive clutch pulley. Re-tension the new deck drive b...
Page 24: 6. Troubleshooting Section
6. Troubleshooting section problem cause remedy discharge chute plugged grass too wet. Wait for grass to dry. Grass too long. Raise cutting height and cut grass twice. Cutting too low. Raise cutting height. Engine rpm too low. Mow at full throttle. Ground speed too fast. Slow down. Streaking of uncu...
Page 26
!! ! ! " ! !".
Page 27
" ! # $%$ "& ' () ' * +,- #., /-01.+#,+23 ) 45,67 0'*)-8$), '$%9: ; ;77),. ;77)=*7 ) ;$)1($$*/9:./) 0 0 " ),7+ ! )&$; ! )&$; ;77)=*7 9:$ ! *)0$' 0 1 ')/9 ;77)1 9:$ ;77)= =*7 ; ; ! 0' 9)+#( = a' 0'*1' 0' 9)( ; +#()7 #9c$ /,$#%9d $/9:./)1 e) 1 d0b( )48484 !" )=(f0' ;77)#(#0$ ;77)/(#(7 1 )0$) 7 07 g7 (...
Page 28
!"#$%&'( !"#$%&') *#"" +*,- .(* /,0(+.*+12 3*45 !"#$%& !"#$%&!"6'( 7&8%& 7&8.9#$ 75 : :67#$; !25 !68)#=>2$;20?$#"@ +*,- .(* /,0(+.*+12 3*45 !"#$%& !"#$%&!"6') 7&8%& 7&8.9#$ 75 : :67#$; !25 !68)#=>2$;20?$#"@ +*,- .(* /,0(+.*+12 3*45 %5576"8 76"8 (+/'1/% *6="'2 %5576" +*,- .(* /,0(+.*+12 3*45 %"'*#"(/...
Page 29
3!!&))!31 )+ !* )&) ** 4 5 2/01 )-!& $ $ 6 5 % 6 - , 7, 89 $ ::" * # 271. ::;; * # )!2 % ::;" * # 2 6 ::;% * # )!2) 7 3 * ::$ * #-!2/01 2) $ :: * #7 , ) $ 5 >' ? >! 1! )* ?.
Page 30: 8. How to Order Repair Parts
8. How to order repair parts the parts manual contains the replacement part numbers of all components of the quadivator hypercut mower. To obtain replacement parts, please contact your quadivator dealer for service. To locate the nearest dealer, please contact a quadivator representative using the c...
Page 31
Warranty registration – hypercut mower – 05 please fax this sheet to (204) 239-4271 or mail it to: quadivator inc. Po box 1127 1000 – 6 th ave ne portage la prairie manitoba r1n3c5 canada mower model # - mower model type – purchased by (name) address- city state/prov/mail code dealer - date purchase...