R www.Quadrafi re.Com 7033-277h september 1, 2010 do not discard this manual caution • important operating a n d m a i n t e n a n c e instructions included. • leave this manual with party responsible for use and operation. • read, understand and follow these instructions for safe installation and o...
Page 2 7033-277h september 1, 2010 r 3100 wood stove series (acc) hearth & home technologies welcomes you to our tradi- tion of excellence! In choosing a quadra-fire appliance, you have our assurance of commitment to quality, durabil- ity, and performance. This commitment begins with our research of...
September 1, 2010 7033-277h page 3 3100 wood stove series (acc) r section 1: listing and code approvals a. Appliance certifi cations ......................4 b. Mobile home approved ......................4 c. Glass specifi cations ............................4 d. Btu & effi ciency specifi cations ......
Page 4 7033-277h september 1, 2010 r 3100 wood stove series (acc) 1 listing and code approvals the quadra-fire 3100 series wood stove (acc) meets the u.S. Environmental protection agency’s 1990 particulate emission standards. A. Appliance certifi cation c. Glass specifi cations d. Btu & effi ciency ...
September 1, 2010 7033-277h page 5 3100 wood stove series (acc) r 2 getting started a. Design, installation & location consider ations consideration must be given to: • safety • convenience • traffi c fl ow • chimney and chimney connector required it is a good idea to plan your installation on paper...
Page 6 7033-277h september 1, 2010 r 3100 wood stove series (acc) marginal location: • below peak location not recommended: • not the highest point of the roof • wind loading possible multi-level roofs windward leeward recommended: outside air intake on windward side not recommended: outside air int...
September 1, 2010 7033-277h page 7 3100 wood stove series (acc) r exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence stove performance. Your local dealer is the expert in your geographic area and can usually make suggestions or discover solution...
Page 8 7033-277h september 1, 2010 r 3100 wood stove series (acc) floor protector chimney connector insulated " t " flashing listed termination cap trim collar on inside wall listed chimney storm collar wall support roof brace (if required) thimble floor protector thimble, 12" (305mm) of brick ceili...
September 1, 2010 7033-277h page 9 3100 wood stove series (acc) r 3 dimensions and clearances 26-11/16 in. (668mm) 24-5/16 in. (618mm) 6-11/16 in. (170mm) 16 in. (406mm) 11-1/2 in. (292mm) 20-3/4 in. (527mm) cl 4-1/2 in (108mm) outside air connection c l a. Appliance dimensions figure 9.1 front view...
Page 10 7033-277h september 1, 2010 r 3100 wood stove series (acc) appliance dimensions (cont’d) figure 10.1 figure 10.2 figure 10.3 figure 10.4 3100 step top pedestal model 3100 step top leg model 23-7/8 in. (606mm) 33-1/8 in. (841mm) 15-1/16 in. (383mm) 19-1/16 in. (484mm) 10-15/16 in. (278mm) 14-...
September 1, 2010 7033-277h page 11 3100 wood stove series (acc) r b. Clearances to combustibles (ul and ulc) backwall / sidewall a b c d e f e f corner installation g g h * 90° off top up & out ceiling clearance stove to ceiling clearance c d alcove top view g a b alcove side view note: clearances ...
Page 12 7033-277h september 1, 2010 r 3100 wood stove series (acc) a. Hearth protection requirements floor protection: floor protector must be non-com- bustible material, extending beneath heater and to the front, sides and rear as indicated. The fl oor must be non-com- bustible or otherwise adequat...
September 1, 2010 7033-277h page 13 3100 wood stove series (acc) r must extend 2 in. (51mm) beyond each side of pipe (shaded area) note: • illustrations and photos refl ect typical installations and are for design purposes only. • i llustrations/diagrams are not drawn to scale. • actual installation...
Page 14 7033-277h september 1, 2010 r 3100 wood stove series (acc) b. Outside air kit installation 1. Remove all materials from packing box. 2. Using a #2 phillips screw driver attach the fl ex adapter to the stove using 4 screws. Figure 14.1 3. For fl oor instatllations, remove circular” knock-out”...
September 1, 2010 7033-277h page 15 3100 wood stove series (acc) r c. Blower (optional) do not remove. 1. Remove the 3 bolts (1/4”-20 phillips head) on the outer skin at the bottom rear of appliance. 2. Align holes in mounting fl ange of blower with bolt holes in appliance. Blower should be position...
Page 16 7033-277h september 1, 2010 r 3100 wood stove series (acc) note: in canada when using a factory-built chimney it must be safety listed, type ul103 ht (2100 o f) class “a” or conforming to can/ulc-s629m, standard for 650 o c factory-built chimneys. 5 chimney requirements floor protector chimn...
September 1, 2010 7033-277h page 17 3100 wood stove series (acc) r thimble site constructed for masonry chimney installation: components • a minimum length of 12 inches [305mm] (longer for thicker walls) of solid insulated factory-built chimney length constructed to ul 103 type ht 6 inch (152mm) ins...
Page 18 7033-277h september 1, 2010 r 3100 wood stove series (acc) chimney height / rise and run this product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or dia...
September 1, 2010 7033-277h page 19 3100 wood stove series (acc) r d. Chimney termination requirements follow manufacturers instructions for clearance, securing, fl ashing and terminating the chimney. • must have an approved and listed cap • must not be located where it will become plugged by snow o...
Page 20 7033-277h september 1, 2010 r 3100 wood stove series (acc) figure 20.1 sparkarestor cap roof flashing storm collar joist shield/firestop double wall connector pipe floor protector outside air floor vent outsideair rear vent caution the structural integrity of the mobile home floor, wall and ...
September 1, 2010 7033-277h page 21 3100 wood stove series (acc) r 7 appliance set up figure 21.3 do not operate before fully assembling components. Burning your stove without a pedestal or leg kit attached: • will void your warranty. • may result in property damage or personal injury. Warning note:...
Page 22 7033-277h september 1, 2010 r 3100 wood stove series (acc) pedestal and ash removal system (cont’d) figure 22.3 cover ars channel replace both bricks back into firebox figure 22.2 cover plate ash removel drawer adapters oak pedestal trim figure 22.1 installing pedestal assembly 1. Remove scr...
September 1, 2010 7033-277h page 23 3100 wood stove series (acc) r b. Leg kit and ash removal installation (ars) for step top uni-body do not tilt the unit on the cast iron legs. • tilting could lead to property damage. • lift the unit upright and place it into position on the fl oor protector. Caut...
Page 24 7033-277h september 1, 2010 r 3100 wood stove series (acc) note: when the speed control is turned clockwise, it will click on to high speed. Continue to turn the speed control clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop. 1. With the ...
September 1, 2010 7033-277h page 25 3100 wood stove series (acc) r 8 operating instructions b. Wood selection & storage burn only dry seasoned wood. Store wood under cover, out of the rain and snow. Dry and well-seasoned wood will not only minimize the chance of creosote formation, but will give you...
Page 26 7033-277h september 1, 2010 r 3100 wood stove series (acc) 2. Second stage the next stage of burning, the secondary stage, is the period when the wood gives off fl ammable gases which burn above the fuel with bright fl ames. During this stage of burning it is very important that the fl ames ...
September 1, 2010 7033-277h page 27 3100 wood stove series (acc) r f. Burn rates and operating effi ciency for maximum operating effi ciency 1. This appliance has a timer system (acc) that operates the stove at its maximum effi ciency removing any guess work for the homeowner. Follow the instruction...
Page 28 7033-277h september 1, 2010 r 3100 wood stove series (acc) g. Building a fire before lighting your fi rst fi re in the stove: 1. Confi rm the baffl e is correctly positioned. It should be even with the front tube and resting on all tubes. Figure 28.1. 2. Follow instructions on page 32 for cl...
September 1, 2010 7033-277h page 29 3100 wood stove series (acc) r incorrect positions h. Correct baffl e & blanket placement ceramic blanket and baffl e board are not in contact with the back of the fi rebox. Ceramic blanket is not in contact with the back of the fi rebox and not even with the baf-...
Page 30 7033-277h september 1, 2010 r 3100 wood stove series (acc) j. Opacity (smoke) this is the measure of how cleanly your appliance is burn- ing. Opacity is measured in percent; 100% opacity is when an object is totally obscured by the smoke column from a chimney, and 0% opacity means that no sm...
September 1, 2010 7033-277h page 31 3100 wood stove series (acc) r 9 maintaining & servicing your appliance a. Quick reference maintenance guide 2 2 baffl e and blanket placement is critical to heat out- put, effi ciency and overall life of the unit. Make sure the baffl e is pushed all of the way to...
Page 32 7033-277h september 1, 2010 r 3100 wood stove series (acc) b. General maintenance inspection: inspect the system at the appliance connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from t...
September 1, 2010 7033-277h page 33 3100 wood stove series (acc) r 4. Cleaning plated surfaces • frequency: prior to first burn and then as desired • by: homeowner clean all the fi ngerprints and oils from plated surfaces before fi ring the appliance for the fi rst time. If not cleaned properly befo...
Page 34 7033-277h september 1, 2010 r 3100 wood stove series (acc) c. Glass replacement 1. Ensure that the fi re is out and the appliance is cool to the touch. 2. Protect a table or counter top with padding or towels. Protect your hands and wear gloves to prevent injury. 3. Remove the door with the ...
September 1, 2010 7033-277h page 35 3100 wood stove series (acc) r replace the fi rebrick if they become crumbly and/or if there is a 1/4 inch (6.35mm) gap between the bricks. Inspect the fi rebrick after each ash removal. The fi rebox is lined with high quality fi rebrick, which has exceptional ins...
Page 36 7033-277h september 1, 2010 r 3100 wood stove series (acc) e. Baffl e removal 1. Remove all ash from the fi rebox, and extinguish all hot embers before disposal into a metal container. 2. The baffl e board has 2 pieces. With the ceramic blanket still in place, slide one baffl e piece over th...
September 1, 2010 7033-277h page 37 3100 wood stove series (acc) r g. Tube channel assembly replacement removing tube channel assembly 1. Remove the right side shield by removing 2 screws in the back using a phillips head screw driver. 2. Remove 4 screws from channel access cover and remove cover. 3...
Page 38 7033-277h september 1, 2010 r 3100 wood stove series (acc) 10 troubleshooting with proper installation, operation, and maintenance your woodstove will provide years of trouble-free service. If you do experience a prob- lem, this troubleshooting guide will assist a qualifi ed service person i...
September 1, 2010 7033-277h page 39 a. Exploded drawings figure 39.1 3100 series acc service parts beginning mfg date: 07-19-06 ending mfg date: www.Quadrafire.Com r 31m-acc-mbk 31st-acc 1 2 3 4 5 6 7 8 9 10 11 12 13 24 25 see fig. A 7025-020b 6-29-09.
Page 40 7033-277h september 1, 2010 3100 series acc service parts beginning mfg date: 07-19-06 ending mfg date: www.Quadrafire.Com 7025 020b june 29 2009 page 2 of 7 r 31m-acc-mbk 31st-acc part number list on following page. Millennium step top unibody step top unibody 36 37 39 40 41 38 26 27 28 29 ...
September 1, 2010 7033-277h page 41 service parts to order the entire assembly, order the top line part number only. To order an individual part from an assembly, order the part(s) listed in the indented portion. How to order when requesting service or replacement parts for your appliance please pro...
Page 42 7033-277h september 1, 2010 service parts to order the entire assembly, order the top line part number only. To order an individual part from an assembly, order the part(s) listed in the indented portion. How to order r 3100 series acc stocked at depot item description comments part number 2...
September 1, 2010 7033-277h page 43 service parts to order the entire assembly, order the top line part number only. To order an individual part from an assembly, order the part(s) listed in the indented portion. How to order r 3100 series acc stocked at depot item description comments part number c...
Page 44 7033-277h september 1, 2010 service parts to order the entire assembly, order the top line part number only. To order an individual part from an assembly, order the part(s) listed in the indented portion. How to order r 3100 series acc stocked at depot item description comments part number a...
September 1, 2010 7033-277h page 45 service parts to order the entire assembly, order the top line part number only. To order an individual part from an assembly, order the part(s) listed in the indented portion. How to order r 3100 series acc stocked at depot item description comments part number f...
Page 46 7033-277h september 1, 2010 r 3100 wood stove series (acc) c. Warranty policy.
September 1, 2010 7033-277h page 47 3100 wood stove series (acc) r.
R hearth & home technologies 1445 north highway colville, wa 99114 division of hni industries 7033-277h september 1, 2010 page 48 contact information: please contact your quadra-fire dealer with any questions or concerns. For the number of your nearest quadra-fire dealer, log onto www.Quadrafi re.Co...
