Quadra-Fire 4100I-GD-B Manual

Other manuals for 4100I-GD-B: User Manual

Manual is about: 4100-I ACT Wood Insert

Page of 28

Download

Print this page

Bookmark us

DO NOT DISCARD THIS MANUAL

NOTICE

•

Important operating

a n d m a i n t e n a n c e

instructions included.

• Leave this manual with

party responsible for

use and operation.

• Read, understand and

follow these instructions

for safe installation and

operation.

DO N

DIS

WARNING

If the information in these

instructions is not followed

exactly, a fi re may result causing

property damage, personal injury,

or death.

• Do not store or use gasoline or other

fl ammable vapors and liquids in the

vicinity of this or any other appliance.

• Do not overfi re - If heater or chimney

connector glows, you are overfi ring.

Overfi ring will void your warranty.

• Comply with all minimum clearances to

combustibles as specifi ed. Failure to

comply may cause house fi re.

www.quadrafi re.com

4100- I ACT WOOD INSERT

Advanced Combustion Technology (ACT)

O-T

O-T L

Tested and

Listed by

Beaverton

Oregon USA

OMNI-Test Laboratories, Inc.

250-7201D March 27, 2008

1445 North Highway

Colville, WA 99114-2008

Installation and service of this appliance should

be performed by qualifi ed personnel. Hearth &

Home Technologies recommends NFI certifi ed

professionals, or technicians supervised by an

NFI certifi ed professional.

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overfi re and generate

poisonous gases (i.e. carbon monoxide).

HOT SURFACES!

G L A S S A N D O T H E R

S U R FA C E S A R E H O T

DURING OPERATION AND

COOL DOWN.

WARNING

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep

children

away

• CAREFULLY SUPERVISE children in the same room

as appliance

• Alert children and adults to hazards of high

temperatures

High temperatures may ignite clothing or other

fl ammable materials.

• Keep clothing, furniture, draperies and other

combustibles away.

Models:

4100I-GD-B

4100I-NL-B

1 2 3 4 5 6 7 Next › »

Summary of 4100I-GD-B

Page 1
Do not discard this manual notice • important operating a n d m a i n t e n a n c e instructions included. • leave this manual with party responsible for use and operation. • read, understand and follow these instructions for safe installation and operation. Do n o t dis ca rd warning if the informa...
Page 2: Caution
4100-i act wood insert page 2 march 27, 2008 r 250-7201 rev d and welcome to the quadra-fire family ! Hearth & home technologies welcomes you to our tradition of excellence! In choosing a quadra-fire appliance, you have our assurance of commitment to quality, durability, and performance. This commit...
Page 3
Page 3 march 27, 2008 4100-i act wood insert 250-7201 rev d r safety & overview of appliance dimensions ----------------------------------------------------- 4 minimum clearances to combustibles ------------------ 5 listings ---------------------------------------------------------- 6 chimney height...
Page 4: Dimensions
4100-i act wood insert page 4 march 27, 2008 r 250-7201 rev d dimensions top view side view front view 20-7/8" (530mm) 30 o 10-7/8" (276mm) 21-5/8" (549mm) 7-7/8" (200mm) 16-1/4" (413mm) cl 24" (610mm) 30" (762mm) 12-1/8" (308mm) 9-5/16" (135mm) 45-3/4" (1162mm) a b 30-7/8" (784mm) 44-3/4” (1137mm) ...
Page 5
Page 5 march 27, 2008 4100-i act wood insert 250-7201 rev d r hearth extension a b c d f e insert sidew all maximum mantel depth - 10" (254mm) fascia or trim mantel thermal protection usa & canada usa canada a sidewall to stove 15" (381mm) 15" (381mm) b mantel to stove 26" (660mm) 23" (584mm) c top ...
Page 6
4100-i act wood insert page 6 march 27, 2008 r 250-7201 rev d avoid fire: to ensure that insulation or any other com- bustible material does not contact the chimney, a chimney inside the house must have at least 2 inches (51mm) of air space clearance around the chimney. A chimney outside the house m...
Page 7
Page 7 march 27, 2008 4100-i act wood insert 250-7201 rev d r if installing this model to a masonry chimney, always be sure the chimney is in good condition and that it meets the minimum standards of the national fire protection association (nfpa) standard 211. A factory built chimney must be 6 inch...
Page 8
4100-i act wood insert page 8 march 27, 2008 r 250-7201 rev d floor ceiling caulk floor (second story) non-combustible firestopping material minimum 1 inch (25mm) clearance from exterior chimney to sheathing firestopping 2 inch (51mm) a chimney must be the required height above the roof or other obs...
Page 9
Page 9 march 27, 2008 4100-i act wood insert 250-7201 rev d r 1. An outside air inlet must be provided for combustion and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability ...
Page 10
4100-i act wood insert page 10 march 27, 2008 r 250-7201 rev d masonry fireplace using direct-connect method refer to: clearances to combustibles on page 5, canadian installation requirements on page 12, hearth requirements on page 5 and zero clearance adjustable support kit on page 16. Figure 10a -...
Page 11
Page 11 march 27, 2008 4100-i act wood insert 250-7201 rev d r factory-built zero clearance fireplace (usa installations only) the quadra-fire 4100-i insert is listed to ul 1482 standard and is approved for installation into listed factory-built zero clearance fi replaces listed to ul 127 conforming...
Page 12
4100-i act wood insert page 12 march 27, 2008 r 250-7201 rev d leveling bolts sheet metal shims place under leveling bolts and slide insert into place leveling bolt reach between side of insert and outer skin cut-out view this product shipped with two leveling bolts, and two sheet metal guides for e...
Page 13
Page 13 march 27, 2008 4100-i act wood insert 250-7201 rev d r securing liner to chimney ring there are two options to secure the liner to the chim- ney ring: see figure 13a. Option one: if there is enough room on the top of the insert to work, hand bend the two tabs upward 90°. Secure the liner wit...
Page 14
4100-i act wood insert page 14 march 27, 2008 r 250-7201 rev d panel set and cast trim set 1. Remove contents from box being careful not to scratch or damage cast trim pieces. 2. Lay the panel set face down on protective covering to prevent scratching the painted surface. 3. Secure panel set togethe...
Page 15
Page 15 march 27, 2008 4100-i act wood insert 250-7201 rev d r blower cord location & blower control box with switch remove bolt remove bolt remove 4 screws, lift motor from housing this insert comes standard with a blower, installed at the factory with blower cord on right side of insert (as you fa...
Page 16
4100-i act wood insert page 16 march 27, 2008 r 250-7201 rev d zero clearance adjustable trim support two sizes: 9”d x 45”w and 12”d x 50”w, both 2” to10” height adjustment included in kit: ( 1) trim top, (1) trim front, (2) trim sides, double-sided tape (already installed) tools needed: phillips he...
Page 17: Operation
Page 17 march 27, 2008 4100-i act wood insert 250-7201 rev d r wood selection and storage b urn only dry seasoned wood. Dry, well-seasoned wood will not only minimize the chance of creosote formation but will give you the most effi cient heat output. Even dry wood contains at least 15% moisture by w...
Page 18
4100-i act wood insert page 18 march 27, 2008 r 250-7201 rev d 1 . Initial (cold) startup: leave fan off until your insert is hot and a good coal bed is established, approximately 30 minutes after fuel is lit. 2. High burn setting: the fan may be left on throughout the burn. 3. Medium low or medium ...
Page 19
Page 19 march 27, 2008 4100-i act wood insert 250-7201 rev d r start-up air control primary air control figure 19a open - push in close - pull out burning process in recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been placed on the bur...
Page 20
4100-i act wood insert page 20 march 27, 2008 r 250-7201 rev d maintenance care and cleaning of plated surfaces important: you must clean all the fi ngerprints and oils from the plated surfaces before fi ring the insert for the fi rst time. Use warm soapy water and a soft rag, glass cleaner and a pa...
Page 21
Page 21 march 27, 2008 4100-i act wood insert 250-7201 rev d r 2 6-1/8" 2-1/4" 1 1 2 2 3 4 4 4 4 4 4 4 4 4 4 6 6 4 4 5 5 5 brick replacement instructions the fi rebox is lined with high quality fi rebrick which has excep- tional insulating properties. There is no need for a grate, simply build a fi ...
Page 22
4100-i act wood insert page 22 march 27, 2008 r 250-7201 rev d exploded views 5.0" 14.0" 10.0" 21-1/2" r5" ceramic blanket figure 22c 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 17 20 19 item description item description item description 1 ashcatcher 8 baffl e, fiberboard 15 flue tab 2 blower, 180 cfm...
Page 23
Page 23 march 27, 2008 4100-i act wood insert 250-7201 rev d r important: this is dated information. The most current information is located on the quadra-fire web site at www. Quadrafi re.Com. When ordering, supply serial and model numbers to ensure correct part. Service parts and accessories item ...
Page 24
4100-i act wood insert page 24 march 27, 2008 r 250-7201 rev d 27 25 30 29 31 23 20 21 22 28 24 item # part description alphabetical order sku figure 24a accessories part no. Cast trim set, matte black, 5 pc 811-0930 panel set standard, 30-1/2” h x 44-3/4” w (order cast trim separately) 831-2010 pan...
Page 25
Page 25 march 27, 2008 4100-i act wood insert 250-7201 rev d r date of service performed by description of service service and maintenance log.
Page 26: Consumer’S Notes
4100-i act wood insert page 26 march 27, 2008 r 250-7201 rev d consumer’s notes.
Page 27: Lifetime Warranty
Page 27 march 27, 2008 4100-i act wood insert 250-7201 rev d r lifetime warranty limited lifetime warranty the hearth & home technologies limited lifetime warranty guarantees that the following components will work as designed for the life- time of the stove or hearth & home technologies will repair...
Page 28
R march 27, 2008 page 28 • do not discard this manual. • important operating and maintenance instructions included. • read, understand and follow these instruci- tons for safe installation and operation. • leave this manual with party responsible for use and operation. Caution this product may be co...