1 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 models: qfi30-c qfi35-c owner’s manual installation and operation do not discard this manual notice • leave this manual with party responsible for use and operation. Do not discard r • important operating and maintenance instructions included...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 2 listing label information/location model name: ___________________________________________ date purchased/installed: __________________ serial number: __________________________________________ location on fireplace: _____________________ dea...
3 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 safety alert key: • danger! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • warning! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • caution! Ind...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 4 b. Limited lifetime warranty x molded refractory panels 4021-645h 10/15 page 1 of 2 hearth & home technologies limited lifetime warranty hearth & home technologies, on behalf of its hearth brands (“hht”), extends the following warranty for hh...
5 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 b. Limited lifetime warranty (continued) warranty conditions: • this warranty only covers hht appliances that are purchased through an hht authorized dealer or distributor. A list of hht authorized dealers is available on the hht branded webs...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 6 c. Btu specifications models: qfi30-c, qfi35-c laboratory: underwriters laboratories, inc. (ul) type: direct vent heater standard: ansi z21.88-2014 csa 2.33-2014 vented gas fireplace heaters this product is listed to ansi standards for “vente...
7 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 2 operating instructions figure 2.1 general operating parts b. Your fireplace warning! Do not operate fireplace before read - ing and understanding operating instructions. Failure to operate fireplace according to operating instructions could...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 8 c. Clear space warning! Do not place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may dama...
9 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 figure 2.3 control module i. Before lighting fireplace before operating this fireplace for the first time, have a qualified technician : • verify all shipping materials have been removed from inside and/or underneath the firebox. • review pro...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 10 j. Lighting instructions (ipi) for your safety read before lighting to turn off gas to appliance 1. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. 1. Equipped...
11 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 initial break-in procedure • the appliance should be run three to four hours continuously on high. • turn the appliance off and allow it to completely cool. • remove fixed glass assembly. See section 12.H. • clean fixed glass assembly. See s...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 12 glass cleaning frequency: seasonally by: homeowner tools needed : protective gloves, glass cleaner, drop cloth and a stable work surface. Caution! Handle fixed glass assembly with care. Glass is breakable. • avoid striking, scratching or sla...
13 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 venting frequency: seasonally by: homeowner tools needed: protective gloves and safety glasses. • inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc. • verify termination cap cl...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 14 burner ignition and operation frequency: annually by: service technician tools needed: protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer. • verify burner is properly secured and ali...
15 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 a. Typical appliance system notice: illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual vertical termination ...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 16 d. Inspect appliance and components • carefully remove the appliance and components from the packaging. • the vent system components and decorative fronts may be shipped in separate packages. • if packaged separately, the log set and applian...
17 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 5 fireplace size requirements a. Minimum fireplace opening minimum fireplace opening requirements for a standard 3/4 inch deep surround are shown in figure 5.2. For smaller openings, an optional 1-1/2 inch deep surround is available and dime...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 18 figure 5.2 fireplace opening in addition to these dimensions, also reference clearances and mantel projections (section 5.B). Minimum fireplace size location qfi35-c qfi30-c inches millimeters inches millimeters a rear width 23-7/16 595 20-3...
19 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 b. Mantel and wall projections warning! Risk of fire! Comply with all minimum clear- ances to combustibles as specified. Framing or finishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 20 a. Vent termination minimum clearances roof pitch h (min.) ft. Flat to 6/12...........................................................1.0* over 6/12 to 7/12 .................................................1.25* over 7/12 to 8/12 ..............
21 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 7 installation preparation e. Electrical outlet box an outlet box may be installed in a bottom back corner of the existing solid fuel masonry or factory built fireplace to power the appliance. Each unit ships standard with a cord assembly to...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 22 b. Venting components caution! Risk of cuts/abrasions/flying debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. The vertical vent termination system installed on this model includes: • flexi...
23 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 figure 8.2 cut and bend flashing as needed to fit chimney sealant adhesive • trim chimney top plate to minimize excess overhang or bend over flue tile (see figure 8.2). • place 3/8 inch bead of 300ºf silicone on flue tile top. Warning! Risk ...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 24 e. Remote control ipi models: if a remote control kit is used to control blower function, the auxiliary 300 module can only be placed in the control cavity to the right of the control panel. See figure 8.4. Figure 8.4 location of aux300 for ...
25 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 f. Installing adaptor and termination cap for installation of termination cap see minimum vent heights for various pitched roofs (see figure 8.5) . To install adaptor see figure 8.6. Roof pitch h (min.) ft. Flat to 6/12....................1....
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 26 figure 8.7 masonry factory built wood burning remove 18 inch x 18 inch flashing on cap by removing 3 screws. Connect both the link-zc-adpb to class a pipe and the termination cap to the link-zc-adpb with the self tapping screws provided. Opt...
27 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 a. Fuel conversion • make sure the appliance is compatible with available gas types. • conversions must be made by a qualified technician (nfi certified or factory-trained) using hearth & home technologies specified and approved parts. B. Ga...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 28 a. Wiring requirements notice: this appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with national electric code ansi/nfpa 70-latest edition or the canadian electric code csa...
29 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 figure 10.2 fan wiring diagram blowers blower receptacle blk grn blk blk grn blk wht grn blk blk grn wht blk blk blk blk plug into 120v existing outlet temperature sensor switch variable speed control dc regulator receptacle fuse wire assemb...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 30 plug 120v existing outlet grn (2) blk (2) blk (2) grn (2) blk (2) steps 3 & 4 wht (2) blower speed control (rheostat) sensor switch steps 1 & 2 step 5 blowers blower recepticle blk grn blk blk grn blk wht grn blk blk grn wht blk blk plug int...
31 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 11 finishing a. Mantel and wall projections warning! Risk of fire! Comply with all minimum clear- ances to combustibles as specified. Framing or finishing material closer than the minimums listed must be construct- ed entirely of noncombusti...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 32 a. Remove glass assembly see section 12.H. B. Remove the shipping materials remove shipping materials from inside or underneath the firebox. C. Clean the appliance clean/vacuum any sawdust that may have accumulated inside the firebox or unde...
33 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 g. Install the log assembly figure 4. Install side refractory figure 5. Bend refractory tab log set assembly: logs-qfi30 models: qfi30, qfi30-c caution: logs are fragile, handle with care. Install back refractory by placing it against the ba...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 34 log #2 (srv2227-702) : rest left end of log on the flat spot of log 1. See figure 6 and figure 8. The left end of the log should touch the left refractory panel. The right end rests on the burner. Push the right end back, until it touches th...
35 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 2227-935b log #4 (srv2227-705) : mate the slot on the bottom of the log, shown in figure 12, with the log pin located on the burner surface. The notch on the right end of the log should mate with the grate bar. See figure 11. Log #5 (srv2227...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 36 g. Install the log assembly log set assembly: logs-qfi35 models: qfi35, qfi35-c install back refractory by placing it against the back of the firebox. The back refractory must be held in the upright position until the side refractory is inst...
37 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 log #2 (srv2225-703) : mate the grate tine with the slot on the bottom of log #2. The back end of the log rests on the log support. The side of the log will contact the left refractory as shown in figure 7. Figure 7. Place log #2 figure 8. S...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 38 2225-935c log #5 (srv2225-710) : position log #5 as shown in figure 12. Mate the middle and left log pins with the two slots located on the bottom of the log. See figure 13 for locations of log slots. The smaller end should be pointed toward...
39 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 i. Air shutter setting air shutter settings should be adjusted by a qualified ser - vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 40 13 troubleshooting with proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified technician in the diagn...
41 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 intellifire™ plus ignition system (continued) symptom possible cause corrective action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (if the pilot continues to spark after the pilot flame has been lit, flame rect...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 42 14 reference materials a. Appliance/decorative front dimension diagrams dimensions are actual appliance dimensions. Use for reference only. Figure 14.1 appliance dimensions model dimensions location qfi35-c qfi30-c inches millimeters inches ...
43 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 af-qfi30, af-qfi35 decorative fronts figure 14.2 decorative front dimensions fsp-qfi30, fsp-qfi35 decorative fronts g a b c d e f a b c d e f g af-qfi30 in. 30 13-1/2 4-5/8 36 23-11/16 23-3/16 1/2 mm 762 343 117 914 602 589 13 af-qfi35 in. 3...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 44 figure 14.3 decorative front dimensions tp-qfi30/tp-qfi35 decorative fronts g a b c d e f a b c d e f g tp-qfi30 in. 32-15/16 12-9/16 4-5/8 36 23-1/2 23 1/2 mm 837 319 117 914 597 584 13 tp-qfi35 in. 35 15-9/16 4-11/16 38-1/16 26-1/2 26 1/2 ...
45 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 figure 14.4 direct vent flex liner kits figure 14.5 direct vent flex liner accessory kits flex3-30 link-dv30b link-zc-adpb dv-46dva-gk flex-cnct b. Vent kits components direct vent flex liner kits (see figure 14.4) link-dv30b: masonry 3 inch...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 46 service parts r beginning manufacturing date: aug 2011 ending manufacturing date: active important: this is dated information. Parts must be ordered from a dealer or distributor. Hearth and home technologies does not sell directly to consume...
47 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 service parts r beginning manufacturing date: aug 2011 ending manufacturing date: active qfi35-c important: this is dated information. Parts must be ordered from a dealer or distributor. Hearth and home technologies does not sell directly to...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 48 service parts r beginning manufacturing date: aug 2011 ending manufacturing date: active important: this is dated information. Parts must be ordered from a dealer or distributor. Hearth and home technologies does not sell directly to consume...
49 quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 service parts r beginning manufacturing date: aug 2011 ending manufacturing date: active important: this is dated information . Parts must be ordered from a dealer or distributor. Hearth and home technologies does not sell directly to consum...
Quadra-fire • qfi30-c, qfi35-c • 2227-901 rev. S • 2/16 50 quadra-fire, a brand of hearth & home technologies 7571 215 th street west, lakeville, mn 55044 www.Quadrafire.Com d. Contact information please contact your quadra-fire dealer with any questions or concerns. For the location of your nearest...
