Electric fireplace heater i n s t r u c t i o n m a n u a l m650-38a-oak ndf-65nb-1 attention: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you read all instructions..
2 s a f e t y i n s t r u c t i o n s important please note when you open the carton carefully check the unit and make sure there are no damages. If you have any problems with the unit, with how the various functions work or with hidden damages or missing parts please call 1-800-459-4409 (est) immed...
3 8) do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 9) to disconnect fireplace, turn controls to off, then remove plug from outlet. 10) connect to properly grounded outlets ...
4 grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. A 15 amp circuit is required to operate this heater. If the breaker trips when the heater is used then you may need to move the heater to another location or un- plug other appliances that are on ...
5 a s s e m b ly i n s t r u c t i o n s parts list: a) top panel 1 b) base panel 1 c) decorative bar 1 d) upper-front panel 1 e) lower-front panel 1 f) left front panel 1 g) right front panel 1 h) left small panel 1 j) right small panel 1 k) left side panel 1 l) right side panel 1 m) drop leaf 1 n)...
6 a s s e m b ly i n s t r u c t i o n s step 2: attach the left small panel (h) to the left front panel(f) with 2 kd screws. Attach the right small panel (j) to the right front panel(g) with 2 kd screws. See fig. B step 3: attach the left side panel (k) to the left front panel (f) with 3 kd screws....
7 step 7: attach the decorative bar (c) over the upper front panel (d) and attach with 2 kd screws (1 screws each side). See fig. G step 8: attach the left triangle sup- port (n) on the left side panel (k). Attach the right triangle support (p) on the right side panel (l). See fig. H step 9: attach ...
8 step 2: carefully lift the insert into the mantle opening. The front of the insert should be flush with the front of the mantle. Step 3: once the insert is in place, attach 3 mounting clips (r) on the top of the insert and lock the insert in place with 3 short kd screws (x). See fig. L fig. L step...
9 o p e r a t i o n after reading complete instructions, confirm all controls on fireplace are in the off posi- tion. Plug the fireplace into a 15amp/120volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 watts. Once the fireplace insert has been proper...
10 maintenance warning disconnect power and unplug the power cord before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. The bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the unit and removing the li...
11 r e p a i r s e t fig. A repairs if any problems are found with the origi- nal parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of the following method. Tools required: electric drill, drill bits 3/4 inches (10 mm) or 1/16 inches ...
12 fig. E option 2: use the small l-brackets and screws 1. Place the small l-bracket to the unit as shown and mark the drill-holes on the mantel as shown in fig. F. Fig. F 2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8mm) on the mantel. Each small l-bracket needs 4 hole...
13 w a r r a n t y power source. Light bulbs are not covered by this warranty. The warranty is for homeowner use only and does not cover units used in commercial situations. Imported by quality craft laval, quebec, canada h7s 2g7 1-800-459-4409 (est) www.Qualitycraft.Com made in china.
