Electric fireplace heater i n s t r u c t i o n m a n u a l m850p-26fdc ndf-62n attention: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you read all instructions..
2 s a f e t y i n s t r u c t i o n s important please note when you open the carton carefully check the unit and make sure there are no damages. If you have any problems with the unit, with how the various functions work or with hidden damages or missing parts please call 1-800-459-4409 (est) immed...
3 8) do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 9) to disconnect fireplace, turn controls to off, then remove plug from outlet. 10) connect to properly grounded outlets ...
4 a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. A 15 amp circuit is required to operate this heater. If the breaker trips when the heater is used then you may need to move the heater to another location or ...
5 a s s e m b ly i n s t r u c t i o n s parts list: fireplace insert 1 a) top panel 1 b) base panel 1 c) upper front panel 1 d) lower front panel 1 e) left front panel 1 f) right front panel 1 g) left upper side panel 1 h) right upper side panel 1 j) left lower side panel 1 k) right lower side pane...
6 fig. A step 2: attach panel e to panel g and j with 1 kd screw. Attach panel f to panel h and k with 1 kd screw. See fig. B. Fig. B step 3: attach 2 x 4-holes wood con- nectors [s] to panel e and f with 4 kd screws (2 screws for each wood con- nector). Attach panels e, g and j to base panel [b] wi...
7 step 6: attach top panel [a] on top with 3 kd screws. See fig. F fig. F step 7: tighten all kd screws. Fireplace insert installation: the fireplace insert can be installed after the mantel has been fully assembled. Warning: make sure the fireplace insert controls are in the off position and the un...
8 o p e r a t i o n wall anchor safety cable the use of wall anchor safety cable is highly recommended in order to reduce the risk of the fireplace being tipped over accidentally. Warning: this cable may reduce possible risk of injury if the fireplace is improperly handled, but is not a substi- tute...
9 m a i n t e n a n c e o/i: press this button for main power and flame effect. The indicator light will turn on. See below for other control switches. 1250w: for heat function - press this switch while the o/i switch is in the on position. The indicator light will turn on. Temperature control: to a...
10 option 1: use the spare kd nuts, kd screws and plastic connector. 1. Place the plastic connector on the mantel unit and mark the drill-holes as shown in fig. B. Fig. B 2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches (10 mm) on the mantel. Each plastic connector needs 3 ho...
11 fig. E option 2: use the small l-brackets and screws. 1. Place the small l-bracket to the unit as shown and mark the drill-holes on the mantel as shown in fig. F. Fig. F 2. Drill the holes with diameter 1/16 inch- es (2 mm) and depth 5/16 inches (8 mm) on the mantel. Each small l-bracket needs 4 ...
12 at 1-800-459-4409 (est). We will, at our discretion either repair or replace the unit. It will have to be returned to us freight prepaid and we will return the repaired or replaced unit to you freight prepaid. The company’s sole obligation is to repair or replace the unit. This warranty is void i...
13.
