Quality Craft MM228R-50EDC Manual

Page of 8

Download

Print this page

Bookmark us

Model: MM228R-50EDC

ElEctric FirEPlAcE

HEAtEr

IMPORTANT:

PlEAsE NOTE: whEN yOu OPEN ThE CARTON CAREfully ChECk ThE uNIT

AND MAkE suRE ThERE Is NO DAMAgE. If yOu hAvE ANy PROblEMs wITh

AssEMblINg ThE uNIT, wITh hOw ThE vARIOus fuNCTIONs wORk OR wITh

DAMAgE OR MIssINg PARTs PlEAsE CAll 1-800-459-4409 (9:00 AM -

5:00 PM EsT) IMMEDIATEly fOR sERvICE.

NOTE: DO NOT RETuRN uNIT TO ThE sTORE bEfORE CAllINg ThE TOll fREE NuMbER.

DO NOT DIsPOsE Of yOuR CARTONs uNTIl yOu ARE COMPlETEly sATIsfIED wITh

yOuR NEw fIREPlACE hEATER.

NOTE: Light bulbs may become loose during shipping. If the flame effect is dim or does

not work, please check that light bulb or bulbs are finger tight in socket. See instructions

for replacing bulb or bulbs.

NOTE: The electric fireplace heater may emit a slight harmless odor when first turned

on. This is caused by activating the internal heater components for the first time and

should not occur again.

iNStrUctiON MANUAl

ATTENTION:

1) Find a location for the fireplace heater that is protected from direct sunlight.

2) Do not plug the unit into the power outlet before reading all instructions.

iMPOrtANt SAFEtY iNStrUctiONS

whEN usINg ElECTRICAl APPlIANCEs, bAsIC PRECAuTIONs shOulD AlwAys

bE fOllOwED TO REDuCE ThE RIsk Of fIRE, ElECTRIC shOCk, AND INJuRy

TO PERsONs, INCluDINg ThE fOllOwINg:

1) Read all instructions before using this electric fireplace heater.

2) This electric fireplace heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. The grill directly in front of the heater outlet

becomes hot during heater operation. keep combustible materials, such

as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet

(0.9 m) away from the front of the unit and keep them away from the sides

and rear.

3) Extreme caution is necessary when any heater is used by, or near, children or

individuals with disabilities and whenever the fireplace is left operating

and unattended.

4) Always unplug fireplace when not in use.

5) Do not operate any electric fireplace with a damaged cord or plug or after the

heater malfunctions, has been dropped or damaged in any manner.

6) Do not use outdoors.

7) This electric fireplace heater is not intended for use in bathrooms, laundry

areas and similar indoor locations. Never place electric fireplace heater

where it may fall into a bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners,

or similar coverings. Arrange cord away from traffic area and where it will

not be tripped over.

9) To disconnect fireplace, turn controls to off, then remove plug from outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or fire, or damage the heater.

12) To prevent a possible fire, do not block air intakes or exhaust in any manner.

Do not use on soft surfaces, like a bed, where openings may become blocked.

13) A heater has hot and arcing or sparking parts inside. Do not use it in areas

where gasoline, paint, or flammable liquids are used or stored.

14) use this fireplace heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury to

persons.

15) Avoid the use of an extension cord because the extension cord may overheat

and cause a risk of fire. however, if you have to use an extension cord, the

cord shall be No. 14 Awg minimum size and rated not less than 1875 watts.

16) Caution: Do not plug this product into a receptacle controlled by a wall switch

or dimmer.

17) when storing or transporting the unit and cord, keep in a dry place, free from

excessive vibration and store so as to avoid damage.

SAVE tHESE iNStrUctiONS FOr FUtUrE USE.

CAuTION:

If yOu usE ThIs hEATER IN CONJuNCTION wITh A ThERMAl CONTROl, A

PROgRAM CONTROllER, A TIMER OR ANy OThER DEvICE ThAT swITChEs ThE

hEATER ON AuTOMATICAlly, REMEMbER TO ObsERvE All sAfETy wARNINgs

AT All TIMEs. ThE fIREPlACE hEATER hAs sAfETy OvERhEAT PROTECTION. If

ThE OvERhEAT PROTECTION TRIPs, swITCh Off All swITCh buTTONs AND wAIT

APPROxIMATEly 5 -10 MINuTEs. IT shOulD REsET AuTOMATICAlly ONCE ThE

uNIT COOls DOwN.

wARNINg:

PROCEDuREs AND TEChNIquEs If NOT CAREfully fOllOwED wIll REsulT

IN DAMAgE TO ThE EquIPMENT AND wIll ExPOsE ThE usER TO ThE RIsk Of

sERIOus INJuRy, IllNEss OR DEATh.

ThIs ElECTRIC fIREPlACE hEATER Is fOR usE ON 120 vOlTs. ThE CORD hAs

A Plug As shOwN AT A IN IllusTRATION bElOw. AN ADAPTER As shOwN AT

C Is AvAIlAblE fOR CONNECTINg ThREE-blADE gROuNDINg-TyPE Plugs TO

TwO-slOT RECEPTAClEs. ThE gREEN gROuNDINg Plug ExTENDINg fROM ThE

ADAPTER MusT bE CONNECTED TO A PERMANENT gROuND suCh As A PROPERly

gROuNDED OuTlET bOx. ThE ADAPTER shOulD NOT bE usED If A ThREE-slOT

gROuNDED RECEPTAClE Is AvAIlAblE.

A 15 AMP CIRCuIT Is REquIRED TO OPERATE ThIs hEATER. If ThE bREAkER

TRIPs whEN ThE hEATER Is usED ThEN yOu MAy NEED TO MOvE ThE hEATER

TO ANOThER lOCATION OR uNPlug OThER APPlIANCEs ThAT ARE ON ThE sAME

CIRCuIT. If yOu REquIRE AN ExTENsION CORD usE ONE ThAT Is RATED AT 1875

wATTs.

1 2 3 4 5 6 7 Next › »

Summary of MM228R-50EDC

Page 1
1 model: mm228r-50edc electric fireplace heater important: please note: when you open the carton carefully check the unit and make sure there is no damage. If you have any problems with assembling the unit, with how the various functions work or with damage or missing parts please call 1-800-459-440...
Page 2
2 parts list fireplace insert...................................................................................................... 1 a) top panel ........................................................................................................ 1 b) base panel ...................................
Page 3
3 step 1: attach 28 plastic connectors [x] to panels c, d, e, f, g, h, i and k with 56 kd screws [w] as shown in fig. A (2 kd screws for each plastic connector). Fig. A back step 2: attach door hinges [r] to panels g and h with 8 door mounting screws [s]. Attach 16 shelf supporting pins [t] to panel...
Page 4
4 step 6: attach panels i to panels c, d, e and f with 8 kd screws. See fig. F. Fig. F back step 7: attach panel j to panel k as shown in fig. G. Fig. G back step 8: attach panel a to the unit as shown in fig. H with 6 kd screws. Fig. H front step 9: attach magnets [q] to panel e and f with 4 door m...
Page 5
5 step 10: attach shelves [l] to the unit as shown in fig. J. Fig. J front step 11: attach door handles [p] to left door and right door [m and n] with door handle screws [o]. See fig. K. Fig. K step 12: attach left and right doors to the unit as shown in fig. L with 8 door mounting screws [s]. Fig. ...
Page 6
6 operation after reading complete instructions, confirm all controls on fireplace are in the off position. Plug the fireplace into a 15amp/120volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 watts. Once the fireplace insert has been properly connect...
Page 7
7 repair set touch-up repair paint paint directly on the mantel unit if necessary. Repairs if any problems are found with the original parts during mantel assembly, such as the panels cannot be installed with the plastic connector, try to solve by one of the following methods: tools required: electr...
Page 8
8 2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8 mm) on the mantel. Each small l-bracket needs 4 holes. See fig. F. Fig. F fig. G 3. Attach the small l-bracket and lock in place with screws as shown in fig. G. Cleaning to clean unit first turn off controls on unit and u...