- DL manuals
- Quanmax
- Motherboard
- KEMF-4010
- User Manual
Quanmax KEMF-4010 User Manual
Summary of KEMF-4010
Page 1
I kemf-4010 user’s kemf-4010 flexatx embedded motherboard with amd athlon™ single and dual-core processors and amd® 780e + sb710 chipset user’s guide.
Page 2
Ii kemf-4010 user’s contact info: quanmax inc. 5f, no. 415, ti-ding blvd. Sec. 2, neihu district, taipei, taiwan 114 tel: +886-2-2799-2789 fax: +886-2-2799-7399 visit our site at: www.Quanmax.Com © 2009 quanmax inc. All rights reserved. The information in this user’s guide is provided for reference ...
Page 3: Content
Content 3 kemf-4010 user’s content 0h content ...................................................................................................................... 3 figures ....................................................................................................................... 5 tab...
Page 4
Content 4 kemf-4010 user’s chapter 4 ami bios setup .................................................................................... 41 overview ................................................................................................ 41 main menu ............................................
Page 5: Figures
Figures 5 kemf-4010 user’s figures figure 1 block diagram ............................................................................................ 16 figure 2 kemf-4010 mechanical dimensions ......................................................... 17 figure 3 jumper connector .....................
Page 6: Tables
Tables 6 kemf-4010 user’s tables table 1 kemf-4010 specification ................................... 15 table 2 jumper list ............................................. 20 table 3 jp1, jp2, jp3, jp6, jp7, jp13, com port signal / power selection .... 20 table 4 jp4, dio signal / power selection .......
Page 7
Tables 7 kemf-4010 user’s table 35 pci1, 32-bit / 33mhz / 5v-key pci slot ........................ 29 table 36 pcie1, standard pci express x16 slot ........................ 31 table 37 usb1, usb2, usb2.0 pin header ............................ 32 table 38 lpt1, parallel port db-25 connector ...........
Page 8: Safety Instructions
Safety instructions 8 kemf-4010 user’s safety instructions before you begin before handling the product, read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety. Refer to the “advisories” section in the preface for ad...
Page 9
Safety instructions 9 kemf-4010 user’s to help avoid possible damage to system boards, wait five seconds after turning off the computer before removing a component, removing a system board, or disconnecting a peripheral device from the computer. When you disconnect a cable, pull on its connector or ...
Page 10: Preface
Preface 10 kemf-4010 user’s preface how to use this guide this guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and upgrades. Note driver downloads and additional information are available under downloads on our web site: ...
Page 11: Warranty Policy
Preface 11 kemf-4010 user’s their own expense. Changes or modifications not expressly approved by quanmax could void the user's authority to operate the equipment. Note the assembler of a personal computer system may be required to test the system and/or make necessary modifications if a system is f...
Page 12: Maintaining Your Computer
Preface 12 kemf-4010 user’s and building replacement products. If quanmax repairs or replaces a product, its warranty term is not extended. Shipments not in compliance with this limited warranty return policy will not be accepted by quanmax. Limitation of liability in no event shall quanmax be liabl...
Page 13
Preface 13 kemf-4010 user’s altitude operating a system at a high altitude (low pressure) reduces the efficiency of the cooling fans to cool the system. This can cause electrical problems related to arcing and corona effects. This condition can also cause sealed components with internal pressure, su...
Page 14: Chapter 1
Chapter 1 14 kemf-4010 user’s chapter 1 introduction overview the kemf-4010 is a flexatx embedded motherboard that built with the fastest onboard graphics - amd® 780e and supporting amd athlon™ x2 dual-core processor and ddr2 dimm up to 8gb. This embedded board offers the latest video performance an...
Page 15: Product Specifications
Chapter 1 15 kemf-4010 user’s product specifications cpu support amd athlon™ single and dual-core processors chipset amd780e + sb710 memory 2x ddr2 400/533/667/800 dimm socket, up to 8gb bios ami pnp 8mbflash display integrated ati radeon™ hd 3200 graphics dual independent display support single/ du...
Page 16: System Block Diagram
Chapter 1 16 kemf-4010 user’s system block diagram figure 1 block diagram.
Page 17: Mechanical Dimensions
Chapter 1 17 kemf-4010 user’s mechanical dimensions figure 2 kemf-4010 mechanical dimensions.
Page 18: Chapter 2
Chapter 2 18 kemf-4010 user’s chapter 2 hardware settings overview this chapter provides the definitions and locations of jumpers, headers, and connectors. Jumpers the product has several jumpers which must be properly configured to ensure correct operation. Figure 3 jumper connector for a three-pin...
Page 19
Chapter 2 19 kemf-4010 user’s jumper settings and pin definitions for jumper and connector locations, please refer to the diagrams below. Figure 4 kemf-4010 jumper and connector locations.
Page 20: Jumper Settings
Chapter 2 20 kemf-4010 user’s jumper settings to ensure correct system configuration, the following section describes how to set the jumpers to enable/disable or change functions. For jumper descriptions, please refer to the table below . Table 2 jumper list label function jp1 com6 signal / power se...
Page 21
Chapter 2 21 kemf-4010 user’s table 5 jp5, parallel port signal selection jumper setting function 1 1-2 short pin 4 of lpt1 = err# (default) 1-3 short pin 4 of lpt1 = +5v 2 4-6 short pin 6 of lpt1 = +5v 5-6 short pin 6 of lpt1 = init# (default) 3 7-8 short pin 8 of lpt1 = slin# (default) 7-9 short p...
Page 22: Rear Panel Pin Assignments
Chapter 2 22 kemf-4010 user’s table 10 jp14, kb / ms signal selection pin signal name pin signal name 1 +5v 2 gnd 3 kbclk from sio 4 kbdat from sio 5 kbclk to ps2-kbms1 6 kbdat to ps2-kbms1 7 msclk from sio 8 msdat from sio 9 msclk to ps2-kbms1 10 msdat to ps2-kbms1 3-5 4-6 short ps/2 keyboard on ps...
Page 23
Chapter 2 23 kemf-4010 user’s table 14 vga_com1, rs-232 / 422 / 485 port 1 db15+db9 connector pin signal name pin signal name v1 red v2 green v3 blue v4 nc v5 gnd v6 gnd v7 gnd v8 gnd v9 +5v v10 gnd v11 nc v12 ddc data v13 hsync v14 vsync v15 ddc clock c1 rs-232：dcd, data carrier detect rs-422：tx- r...
Page 24
Chapter 2 24 kemf-4010 user’s table 17 ps2-kbms1, ps/2 kb/ms mini-din connector pin signal function 1 kbdat keyboard data 2 nc no connect 3 gnd ground 4 kb5v +5vsb power source 5 kbclk keyboard clock 6 nc no connect 7 msdat mouse data 8 nc no connect 9 gnd ground 10 kb5v +5vsb power source 11 msclk ...
Page 25: Main Board Pin Assignments
Chapter 2 25 kemf-4010 user’s main board pin assignments table 19 internal connector list label function label function atxpwr1 24-pin atx power input connector fp1 front panel 1 pin header atx12v1 4-pin atx power input connector fp2 front panel 2 pin header cfd1 cf type ii connector lvds1 lvds pane...
Page 26
Chapter 2 26 kemf-4010 user’s table 21 atx12v1, 4-pin atx power input connector pin signal pin signal 1 gnd 2 gnd 3 +12v 4 +12v pitch:4.2mm 空心 pin [yimtex 576mwa2*02str] table 22 cfd1, cf type ii connector (this connector is at backside of board.) signal name pin pin signal name gnd 1 26 gnd ide dat...
Page 27
Chapter 2 27 kemf-4010 user’s table 24 dio1, digital input / output pin header pin signal pin signal 1 digital output 0 2 digital input 0 3 digital output 1 4 digital input 1 5 digital output 2 6 digital input 2 7 digital output 3 8 digital input 3 9 +5v / +12v * 10 gnd pitch:2.54mm [yimtex 3322*05s...
Page 28
Chapter 2 28 kemf-4010 user’s table 29 cpu_fan1, fan wafer pin signal 1 gnd 2 +12v 3 fan_rpm 4 fan_rpm_ctl pitch: 2.54mm wafer [foxconn hf2704e-m1] * support cpu smart fan function table 30 cha_fan1, cha_fan2, fan wafer pin signal 1 gnd 2 +12v 3 fan_rpm pitch: 2.54mm wafer [yimtex 521aw1*03str] tabl...
Page 29
Chapter 2 29 kemf-4010 user’s table 33 lvds1, lvds panel connector signal name pin pin signal name nc 2 1 nc +3.3v / +5v* 4 3 +3.3v / +5v* txclkb- 6 5 txclka- txclkb+ 8 7 txclka+ gnd 10 9 gnd txoutb0- 12 11 txouta0- txoutb0+ 14 13 txouta0+ txoutb1- 16 15 txouta1- txoutb1+ 18 17 txouta1+ txoutb2- 20 ...
Page 30
Chapter 2 30 kemf-4010 user’s 11 reserved idsel1 * 12 ground ground 13 ground ground 14 clk1 * +3.3vaux 15 ground rst# 16 clk0 +5v 17 ground gnt0# 18 req0# ground 19 +5v pme# 20 ad[31] ad[30] 21 ad[29] +3.3v 22 ground ad[28] 23 ad[27] ad[26] 24 ad[25] ground 25 +3.3v ad[24] 26 c/be[3]# idsel0 27 ad[...
Page 31
Chapter 2 31 kemf-4010 user’s table 36 pcie1, standard pci express x16 slot pin side b side a 1 +12v prsnt#(b) 2 +12v +12v 3 +12v +12v 4 ground ground 5 smclk jtag2 6 smdat jtag3 7 ground jtag4 8 +3.3v jtag5 9 jtag1 +3.3v 10 +3vsb +3.3v 11 wake# pwrgd 12 reserved ground 13 ground refclk+ 14 hsop0 re...
Page 32
Chapter 2 32 kemf-4010 user’s 62 hsop11 ground 63 hson11 ground 64 ground hsip11 65 ground hsip11 66 hsop12 ground 67 hson12 ground 68 ground hsip12 69 ground hsip12 70 hsop13 ground 71 hson13 ground 72 ground hsip13 73 ground hsip13 74 hsop14 ground 75 hson14 ground 76 ground hsip14 77 ground hsip1...
Page 33
Chapter 2 33 kemf-4010 user’s table 39 pcie2, pcie3, standard pci express x1 slot pin side b side a 1 +12v +3.3v 2 +12v +3.3v 3 +3.3vaux ground 4 wake# refclk+ 5 rst# refclk- 6 ground ground 7 petp0 perp0 8 petn0 pern0 9 ground ground 10 petp1 perp1 11 petn1 pern1 12 smb_clk smb_dat 13 ground ground...
Page 34
Chapter 2 34 kemf-4010 user’s table 41 mpcie1, mini pcie connector signal pin pin signal wake# 1 2 +3.3v reserved 3 4 ground reserved 5 6 +1.5v clkeq# 7 8 uim_pwr ground 9 10 uim_data refclk- 11 12 uim_clk refclk+ 13 14 uim_reset ground 15 16 uim_vpp reserved 17 18 ground reserved 19 20 w_disable# g...
Page 35: Chapter 3
Chapter 3 35 kemf-4010 user’s chapter 3 system installation processor installation processor handling carefully follow the steps below in order to prepare the cpu for installation: 1. Remove processor from packaging. 2. Handle the cpu by grasping the substrate edges only with thumb and forefinger. C...
Page 36: Removing The Cpu:
Chapter 3 36 kemf-4010 user’s 4. Make sure that the cpu pins fit perfectly into their holes. Once the cpu is positioned into its socket, place one finger down on the middle of the cpu, lowering the locking lever and latching it into the fully locked position. Figure 6 cpu installation note you shoul...
Page 37: Cooler Installation
Chapter 3 37 kemf-4010 user’s cooler installation the system must not be operated without a cooler (heat sink and fan) to provide the necessarily cooling. Install the cooling unit supplied as follows: caution make sure that good thermal contact is made between the processor and heat sink. Insufficie...
Page 38: Memory Module Installation
Chapter 3 38 kemf-4010 user’s 5. Turn the cam handle from the left side to the right side to lock into place. (refer to your cpu cooler installation manual for instructions on installing the cooler.) figure 9 lock the cpu cooler 6. Attach the power connector of the cpu cooler to the cpu fan header o...
Page 39: Installing A Dimm
Chapter 3 39 kemf-4010 user’s figure 11 dimm memory and 240-pin socket installing a dimm carefully follow the steps below in order to install the dimms: to avoid generating static electricity and damaging the dimm, ground yourself by touching a grounded metal surface or using a ground strap before y...
Page 40: Removing A Dimm:
Chapter 3 40 kemf-4010 user’s removing a dimm: to remove the dimm, use your fingers or a small screwdriver to carefully push away the plastic tabs that secure the dimm at each end. Lift it out of the socket. Note make sure you store the dimm in an anti-static bag. The socket must be populated with m...
Page 41: Chapter 4
Chapter 4 41 kemf-4010 user’s chapter 4 ami bios setup overview this chapter provides a description of the ami bios. The bios setup menus and available selections may vary from those of your product. For specific information on the bios for your product, please contact quanmax. Note the bios menus a...
Page 42: Main Menu
Chapter 4 42 kemf-4010 user’s main menu the bios setup is accessed by pressing the del key after the power-on self-test (post) memory test begins and before the operating system boot begins. Once you enter the bios setup utility, the main menu will appear on the screen. The main menu provides system...
Page 43: Advanced Menu
Chapter 4 43 kemf-4010 user’s not previously formatted with lba mode disabled. Options: disabled, auto dma mode [auto] setup dma mode. S.M.A.R.T [auto] smart stands for smart monitoring, analysis, and reporting technology. It allows amibios to use the smart protocol to report server system informati...
Page 44
Chapter 4 44 kemf-4010 user’s booting to decrease the time needed to boot the system. When set to [disabled], bios performs all the post items. Options: disabled, enabled full screen logo display [disabled] disabled: displays normal post messages. Enabled: displays oem logo instead of post messages....
Page 45
Chapter 4 45 kemf-4010 user’s table 47 onboard peripherals configuration settings bios setup utility m a i n a d v a n c e d b o o t c h i p s e t p o w e r s e c u r i t y e x i t onboard peripherals configuration settings usb controller legacy usb support onboard lan1 controller onboard lan2 contr...
Page 46
Chapter 4 46 kemf-4010 user’s onchip sata channel [enabled] options: enabled, disabled onchip sata type [ide] options: ide, raid, ahci table 49 onboard i/o configuration bios setup utility m a i n a d v a n c e d b o o t c h i p s e t p o w e r s e c u r i t y e x i t onboard i/o configuration com1 ...
Page 47
Chapter 4 47 kemf-4010 user’s options: normal, irda, ask ir com6 address [220] options: disabled, 3f8, 2f8, 3e8, 2e8, 228 220 com6 irq [7] options: 3, 4, 5, 6, 7, 11 parallel port address [378] options: 378, 278, 3bc parallel port mode [normal] options: normal, epp, ecp, epp+ecp parallel port irq [i...
Page 48: Boot Menu
Chapter 4 48 kemf-4010 user’s cpu warning temperature options: disabled, 80 °c/176°f, 85°c/185°f, 90°c/194°f, 95°c/203°f cpu shutdown temperature options: disabled, 80 °c/176°f, 85°c/185°f, 90°c/194°f, 95°c/203°f boot menu table 52 boot menu bios setup utility m a i n a d v a n c e d b o o t c h i p...
Page 49
Chapter 4 49 kemf-4010 user’s lvds1 port type [lvds 24bit] options: dvi, lvds 24bit, lvds 18bit video display devices [auto] options: auto, vga, lvds, hdmi, lvds+vga, hdmi+vga, hdmi+lvds panel type [1600x1200 24bit 2ch] lvds 24bit lvds 18bit 1024x768, 24-bit, 1-ch 1280x1024, 24-bit, 2-ch 1600x1200, ...
Page 50: Power Menu
Chapter 4 50 kemf-4010 user’s power menu table 55 power menu bios setup utility m a i n a d v a n c e d b o o t c h i p s e t p o w e r s e c u r i t y e x i t power management setting acpi function suspend mode repost video on s3 resume power button mode restore on ac power loss > wake up event set...
Page 51: Security Menu
Chapter 4 51 kemf-4010 user’s resume from s3 by usb device [disabled] options: disabled, enabled resume by pci device (pme#) [disabled] options: disabled, enabled resume by pcie device [disabled] options: disabled, enabled resume by rtc alarm [disabled] options: disabled, enabled security menu table...
Page 52: Exit Menu
Chapter 4 52 kemf-4010 user’s exit menu table 58 exit menu bios setup utility m a i n a d v a n c e d b o o t c h i p s e t p o w e r s e c u r i t y e x i t exit setting save changes and exit discard changes and exit discard changes load optimal defaults load failsafe defaults exit system setup aft...
Page 53: Chapter 5
Chapter 5 53 kemf-4010 user’s chapter 5 driver installation if your kemf-4010 does not come with an operating system pre-installed, you will need to install an operating system and the necessary drivers to operate it. After you have finished assembling your system and connected the appropriate power...
Page 54: Appendix A
Appendix a 54 kemf-4010 user’s appendix a dio (digital i/o) programming guide i/o port cf8~b: address port (32bit) i/o port cfc~f: data port (32bit) base number: 0x8000a000 pci reg reg a8h: bit 21--dio_in2 reg a8h: bit 17--dio_in3 reg a8h: bit 24--dio_out0 reg a8h: bit 2--dio_out1 reg 50h: bit 9--di...
Page 55: Appendix B
Appendix b 55 kemf-4010 user’s appendix b watchdog timer sample code //============================================ //kemf-4010 dos watchdog sample program //please compile with turbo c 3.0 to utilized the program //============================================ int main(){ //initialized the wdt progr...