1. DL manuals
  2. Quantum
  3. Wheelchair
  4. edge 2.0
  5. Owner's Manual

Quantum edge 2.0 Owner's Manual

Summary of edge 2.0

  • Page 1

    Product serial # usa 401 york avenue duryea, pa 18642 canada 5096 south service road beamsville, ontario l0r 1b3 uk 32 wedgwood road bicester, oxfordshire ox26 4ul australia 20-24 apollo drive hallam, victoria 3803 italy via del progresso, ang. Via del lavoro loc. Prato della corte 00065 fiano roman...

  • Page 2: Safety Guidelines

    Safety guidelines quick reference information quantum rehab provider: address: phone number: purchase date: warning! A quantum rehab provider or a qualifi ed technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are use...

  • Page 3: Language Usage

    Introduction ..............................................................................................6 safety ........................................................................................................7 your power chair ................................................................

  • Page 4: Identifi Cation Key

    Identifi cation key 11 9 10 8 12 a b 1 3 13 2 4 5 7 6.

  • Page 5: Identifi Cation Key

    Identifi cation key a 1 2 3 4 5 b 6 7 8 9 10 11 12 13 seat assembly seatback armrest seat base joystick controller power base assembly rear shroud trapeze bar location (if equipped) manual freewheel lever drive wheel spring shock/ gas damper location caster wheel front rigging (foot platform shown) ...

  • Page 6: Introduction

    Introduction safety welcome to quantum rehab. The power chair you have purchased combines state-of-the-art components with safety , comfort, and styling in mind. We are confi dent that these design features will provide you with the conveniences you expect during your daily activities. Once you unde...

  • Page 7: Product Safety Symbols

    Product safety symbols the symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Note: there are more warnings identifi ed and explained in the consumer safety guide that is incl...

  • Page 8: General Guidelines

    General guidelines mandatory! Do not operate your new power chair for the fi rst time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. We provide an extensive variety of products to best fi...

  • Page 9: Provider For Assistance.

    Check all controller connections to the power base. Make sure they are secured properly. Check the brakes. See “care and maintenance.” check battery charge. See “batteries and charging.” ensure the manual freewheel levers are in drive mode before sitting on the power chair. Note: if you discover a p...

  • Page 10: Your Power Chair

    Your power chair the q6 edge 2.0 power chair your power chair has two main assemblies: the seat assembly and the power base assembly. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/ brake assemblies, two drive wheels, four cast...

  • Page 11: Identifi Cation Key

    Figure 2. Manual freewheel lever operation figure 1. Q6 edge 2.0 electrical components identifi cation key 1. To motor connector 2. Controller power module 3. Controller connector 4. To battery connectors 5. To motor connector 6. Main circuit breaker 7. Quick release battery connectors 8. Suspension...

  • Page 12: See Fi Gure 2.

    Warning! Do not use the power chair while the drive motors are disengaged! Do not disengage the drive motors when the power chair is on an incline, as the unit could roll on its own! Only engage the freewheel mode when on a level surface. Warning! It is important to remember that when your power cha...

  • Page 13: Ilevel®

    Ilevel® engaged figure 3. Q6 edge 2.0 with ilevel® feature and controller indicators ilevel® boot (1 of 2 shown) q-logic 2 controller ne+ controller ilevel® not engaged ilevel® engaged ilevel® not engaged single switch.

  • Page 14: Your Controller.

    Mandatory! Before operating the ilevel® feature, read the following. These guidelines are provided for your benefi t and will aid you in the safe operation of the ilevel® feature. Turn off the power before you are seated in your power chair. Always have assistance when you are being seated in or tra...

  • Page 15: Fender Lights (Optional)

    Warning! The ilevel® feature is intended for limited outdoor use on only fl at, level, hardscape surfaces. If you are unsure of your environment, do not use ilevel® outdoors. Prohibited! Never use the ilevel® outdoors on uneven terrain (gravel, hills or other uneven, non-compact terrain) or in fi el...

  • Page 16: Bination:

    Figure 4. Q6 edge 2.0 with single switch to operate fender lights to activate the fender lights using the controller/single switch com- bination: 1. Turn on the power to the controller. 2. Defl ect the joystick in any direction. To deactivate the fender lights using the controller/single switch com-...

  • Page 17: Chair.

    If operated through the controller/single switch combination, the fender lights will turn on when the power chair is turned on and the joystick is de- fl ected in any direction. The power chair must remain powered on for the lights to stay illuminated. When the power chair is turned off, the lights ...

  • Page 18: Initial Assembly

    Initial assembly your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 5 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a q...

  • Page 19: See

    Mandatory! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for controller harness to prevent the harness from getting caught in the driv...

  • Page 20: Identifi Cation Key

    3 1 4 2 figure 5. Q6 edge 2.0 assembly view figure 6. Universal mounting system and contour seat identifi cation key identifi cation key 1. Armrest angle adjustment 2. Controller position 3. Foot platform angle adjustment 4. Foot platform height/depth adjustment 1. Rear extrusion 2. Seat latch safet...

  • Page 21: Actuator

    1 figure 7. Controller harness routing on a tru-balance® 3 figure 9. Power elevating seat actuator figure 8. Controller harness routing on a contour seat figure 10. Transit system securement brackets identifi cation key identifi cation key identifi cation key 1. Seat plate interface bracket 2. Actua...

  • Page 22: Comfort Adjustments

    Comfort adjustments comfort adjustments after becoming familiar with your power chair’s operation, you may fi nd the need to make some adjustments to increase your comfort, such as seat height and angle, armrest width, angle and height, foot platform height, depth, and angle, and controller position...

  • Page 23: Seat Position

    Seat position you can move the seat forward or rearward by changing the extrusion mounting position. To change the position: 1. Turn off the power to the controller. 2. Make sure the power chair is in drive mode. 3. Unplug the controller connector(s) from the power base. 4. Remove the seat from the ...

  • Page 24: Seatback Angle Adjustment

    Seatback angle adjustment if your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90 , 102 , 105 , or 107 . To adjust the seatback angle: 1. Remove the adjusting screws from each seat hinge. See fi gure 13. 2. Set the seatback at the desired angle...

  • Page 25: See Fi Gure 13.

    To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See fi gure 13. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. To change the controller position: 1. Turn off the power to the controller. 2. U...

  • Page 26: See Fi Gure 14.

    Foot platform height adjustment the foot platform height is easily adjusted to several different heights. To raise or lower the foot platform: 1. Remove the hardware from the foot platform bracket. See fi gure 14. 2. Raise or lower the foot platform to the desired height. 3. Reinstall the hardware i...

  • Page 27: See Fi Gure 14.

    Foot platform depth adjustment you can adjust the depth of the foot platform. To adjust the foot platform depth: 1. Remove the hardware from the foot platform bracket. See fi gure 14. 2. Move the foot platform in or out to the desired depth. 3. Reinstall the hardware into the foot platform bracket a...

  • Page 28: Toggle Switch

    Figure 14. Foot platform adjustment figure 15. Power elevating seat toggle switch identifi cation key 1. Foot platform bracket 2. Hardware 3. Screw 1 2 3 note: the power elevating seat option is equipped with a system that reduces the speed of the power chair to one quarter when the seat is elevated...

  • Page 29: See Fi Gure 16.

    Warning! The positioning belt should be secured at all times. Never allow the positioning belt to hang or drag on the fl oor as it may become entangled. To install the positioning belt: 1. Remove the rearmost screw that holds the seat hinge to the seat base on both the left and right seat hinges. 2....

  • Page 30: Batteries and Charging

    Batteries and charging the q6 edge 2.0 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fl uid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Th...

  • Page 31: See Fi Gure 17.

    Warning! Inspect the battery charger, wiring, and connectors for damage before each use. Contact your quantum rehab provider if damage is found. Warning! Do not attempt to open the battery charger case. If the battery charger does not appear to be working correctly, contact your quantum rehab provid...

  • Page 32: How Does The Charger Work?

    Frequently asked questions (faqs) how does the charger work? The battery charger takes the standard electrical outlet voltage (alternating current) and converts it to 24 vdc (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the c...

  • Page 33: Daily Use

    Daily use if you use your power chair on a daily basis, charge the batteries as soon as you are fi nished using your power chair. Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the batteries at least 8 to 14 hours after daily use. We r...

  • Page 34: —

    Why do my new batteries seem weak? Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads), or in other common battery types. Deep-cycle batteries are specifi cally designed to provide power, drain down their charge, and then accept a...

  • Page 35: What About Shipping?

    What about public transportation? Agm and gel-cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are federal aviation administration (faa) approved, allowing safe transportation on aircraft, buses, and trains, as there is no danger of spillage or...

  • Page 36: Care and Maintenance

    Care and maintenance your q6 edge 2.0 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your quantum rehab provider. Preventive maintenance is very important. If you follow the ...

  • Page 37: General Guidelines

    General guidelines avoid knocking or bumping the controller, especially the joystick. Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture. Keep the controller clean. Check all connectors to ensure that they are all tight and secured properly. Make sure...

  • Page 38: Weekly Checks

    Visually inspect the controller harness. Make sure that it is not frayed, cut, or has any wires exposed. See your quantum rehab provider if there is a problem. Check for fl at spots on solid tires. Flat spots could adversely affect stability. Inspect the seating system, armrests, and front riggings ...

  • Page 39: Yearly Checks

    Spring shocks and gas dampers should be visually checked for any abnormality, structure damage, or bent rods. See your quantum rehab provider for repair. Yearly checks take your power chair to your quantum rehab provider for yearly maintenance, especially if you use your power chair on a daily basis...

  • Page 40: Wheel Replacement

    Warning! Follow all safety instructions for the proper use of the disinfectant and/or cleaning agent before applying it to your product. Failure to comply may result in skin irritation or premature deterioration of upholstery and/or power chair fi nishes. Warning! Never hose off your power chair or ...

  • Page 41: Identifi Cation Key

    1 2 figure 18. Q6 edge 2.0 drive wheel figure 19. Q6 edge 2.0 drive wheel disassembled identifi cation key identifi cation key 1. Lug nuts 2. Wheel hub 1. Front rim half 2. Tube 3. Tire 4. Rear rim half 5. Screws 3 4 5 2 1.

  • Page 42: Battery Replacement

    Battery replacement a battery wiring diagram is printed on a decal located on the front cover. See the specifi cation table for correct battery specifi cations. Mandatory! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteri...

  • Page 43: Identifi Cation Key

    1 2 3 6 4 5 figure 20. Battery installation identifi cation key 1. Quick release battery connectors 2. Rear battery 3. Front battery 4. Front cover 5. Release handles 6. Battery wiring diagram label battery seat confi guration: + = positive (red) terminal post - = negative (black) terminal post conn...

  • Page 44: Corrective Maintenance

    When to see your quantum rehab provider for service the following symptoms could indicate a serious problem with your power chair. If necessary, contact your quantum rehab provider. When calling, have the model number, serial number, nature of the problem, and the error code if available. Motor nois...

  • Page 47: Safety Guidelines

    Safety guidelines quick reference information quantum rehab provider: address: phone number: purchase date: warning! A quantum rehab provider or a qualifi ed technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are use...

  • Page 48: Owner’S Manual

    Product serial # usa 401 york avenue duryea, pa 18642 canada 5096 south service road beamsville, ontario l0r 1b3 uk 32 wedgwood road bicester, oxfordshire ox26 4ul australia 20-24 apollo drive hallam, victoria 3803 italy via del progresso, ang. Via del lavoro loc. Prato della corte 00065 fiano roman...